Dimplex Prism BLF5051 Bedienungsanleitung

Owner’s Manual

Model

BLF5051

7213940100R02

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician or

service agency to repair this replace.

!NOTE: Procedures and tech-

niques that are considered impor-

tant enough to emphasize.

CAUTION: Procedures and

techniques which, if not carefully

followed, will result in damage to

the equipment.

WARNING: Procedures and

techniques which, if not carefully

followed, will expose the user to

the risk of re, serious injury, or

death.

Welcome & Congratulations ...................3

IMPORTANT INSTRUCTIONS ..................4

Quick Reference Guide ......................6

Fireplace Installation ........................7

Site Selection ...................................... 7

Wiring ............................................ 8

Hardwire Installation ................................. 8

Surface Installation ................................. 11

In-wall Recessed Installation - 2x4 Framing .............. 13

Flush Mounted Installation - 2x8 Framing ............... 14

Front Glass Installation .............................. 15

Operation ................................17

Maintenance .............................21

Warranty ................................22

Replacement Parts ........................24

Welcome & Congratulations

Thank you and congratulations for purchasing an electric replace from

Dimplex. Please use our convenient online registration page to record

your model and serial numbers for future reference at

www.dimplex.com/register

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

In order to better serve you, please have your model and serial number

ready or register your product online before calling (See above)

Serial Number

Label Rating Label with

Model Number

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before

using this electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces. The

surface around the heater outlet

becomes hot during heater opera-

tion.

DANGER: High temperatures

may be generated under certain

abnormal conditions. Do not par-

tially or fully cover or obstruct the

front of this heater.

③Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④Young children should be

supervised to ensure that they do

not play with the appliance.

⑤ The appliance is not intended

for use by young children or

inrmed persons without supervi-

sion.

⑥Do no operate any heater

after it malfunctions. Disconnect

power at service panel and have

heater inspected by a reputable

IMPORTANT INSTRUCTIONS

electrician before reusing.

⑦ If the supply cord is dam-

aged, it must be replaced by the

manufacturer, or its service agent,

or a qualied person in order to

avoid a hazard. Contact Dimplex

Technical Service for obtaining a

replacement cord at

1-888-346-7539.

⑧ Do not use outdoors.

⑨Never locate replace where

it may fall into a bathtub or other

water container.

⑩ Do not locate the heater im-

mediately below a xed socket-

outlet.

⑪ To disconnect the replace,

turn the controls off, and turn off

power to heater circuit at main

disconnect panel.

⑫Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑬ To prevent a possible fire, do

not block air intakes or exhaust in

any manner.

⑭ A heater has hot and arcing or

sparking parts inside. Do not use

in areas where gasoline, paint,

or ammable liquids are used or

stored.

SAVE THESE INSTRUCTIONS

⑮Use this heater only as

described in this manual. Any

other use not recommended by

the manufacturer may cause fire,

electric shock or injury to persons.

⑯ To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will fit in a

polarized outlet only one way. If

the plug does not fit fully in the

outlet, reverse the plug. If it still

does not fit, contact a qualified

electrician to install the proper

outlet. Do not change the plug in

any way. Always plug heaters di-

rectly into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰Do not burn wood or other

materials in the electric replace.

⑱ Do not strike the replace

glass.

⑲ Always use a certied electri-

cian should new circuits or outlets

be required.

⑳Always use properly ground-

ed, fused and polarized outlets.

㉑ Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

㉒ When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains small batteries. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

Quick Reference Guide

Figure 1

① The electrical information

regarding your electric replace can

be found on the rating label located

on the front of the unit, behind the

glass.

Before installation, please record your

replace's serial number below for

future reference.

② If you have any technical

questions or concerns regarding the

operation of your electric replace,

or require service contact customer

service.

③ For dimensions of your replace,

refer to Figure 1.

3" (7.6 cm)

50 516" (128 cm)

19 12

(49.5 cm)

46" (116 cm)

48 12 " (123 cm)

(17.8 cm)

3 1316"

(9.7 cm)

18"

(45.7 cm)

16"

(40.6 cm)

Site Selection

Review and consider all of the fol-

lowing conditions for installation:

• Dimensions of the unit: 505/16"

(128cm) x 19½"(49.5cm)

• Unit requires a minimum of two

wall studs in order to ensure a

secure installation

There are three possible mount-

ing methods:

• Surface mount (pg. 11);

• In-wall Recessed (pg. 13);

• Flush mount (pg. 14),

and any of these have the option

of being hard-wired or plugged

directly into the wall outlet.

!NOTE:If the desired replace

location is on the interior of an ex-

terior wall the unit should only be

surface mounted. If an in-wall or

ush mount look is desired build

the interior wall out into the room.

!NOTE 1: A 15 Amp, 120 Volt

circuit is required. A dedicated

circuit is preferred but not essen-

tial in all cases. A dedicated circuit

will be required if, after installa-

tion, the circuit breaker trips or

fuse blows on a regular basis

when the heater is operating. Ad-

ditional appliances on the same

circuit may exceed the current

Fireplace Installation

rating of the circuit breaker.

WARNING: Ensure the power

cord is not installed so that it

is pinched or against a sharp

edge and ensure that the

power cord is stored or secured

to avoid tripping or snagging to

reduce the risk of re, electric

shock or injury to persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

WARNING: To reduce the risk

of re, do not store or use gaso-

line, or other ammable vapors or

liquids in the vicinity of the heater.

1. Select a location that is not

susceptible to moisture and

is away from drapes, furniture

and high trafc.

2. For ease of electrical hook up

you may wish to locate the

replace near an existing outlet

(for plug-in convenience) (refer

to NOTE 1).

3. Remove replace, front glass

and hardware from box and

remove all packaging materials

before installation.

8 www.dimplex.com

Fireplace Installation

4. Store the replace in a safe,

dry and dust free location until

you are ready to install the

replace.

Hardwire Installation

The replace is packaged with a

two prong plug installed for plug-

in convenience. Hard wiring the

replace is also an option for any

installation.

WARNING: Do not attempt

to wire your own new outlets

or circuits. To reduce the risk

of re, electric shock or in-

jury to persons, always use a

licensed electrician.

WARNING: Ensure that the

circuit on which the replace is

to be installed has the power

cut off at the service panel

until installation is complete.

Figure 2

Partially

Reective Glass

Glass Bracket

Bracket Screws

1. Remove the partially reective

glass from the replace:

• Lay replace on its back.

• Remove two Phillips screws

from each of the two glass

brackets (Figure 2).

• Remove glass brackets.

• With one hand keeping pres-

Wiring

MOTOR

HEATER NEUTRAL

FLAME COLOR

TOP LIGHT

LOG MEDIA NTC

GESTURE DISPLAY

FAN

LINE

LED CONTROL

BOARD

LED LIGHTS

NTC

MOTOR

HEATER

LINE

LED LIGHTS

LED LIGHTS LED LIGHTS

LED LIGHTS

SWITCH

BOARD

DISPLAY

BOARD

120V~

60Hz

sure on the partially reective

glass, tilt the replace upright

and slightly forward to allow

the partially reective glass to

fall out of the inside framing.

CAUTION: Partially reective

glass is not tempered. Do not

bump or drop the partially reec-

tive glass to avoid breakage and

personal injury.

• Remove partially reective

glass from replace.

2. Locate the power cord and

remove the 3 screws that at-

tach the metal bracket to the

unit - one on the back of the

unit and two on the bottom.

(Figure 4)

3. From the front, remove the 2

Philips screws that fasten the

front panel tabs, tilt the panel

Fireplace Installation

Figure 6

Wires to

controls

Wire connectors

Junction

Box screw

Figure 5

Electrical box

Screw

Figure 3

Front Panel

Front Panel tabs (2)

Acrylic Tray screws (4)

White neutral

wires

Black live

wires

Metal Tray

Screws (4) Figure 4

Junction Box screws (3)

10 www.dimplex.com

Figure 7

Fireplace Installation

9. Replace removed junction

box cover with the supplied

hard-wire cover replacement

(Figure 7) and install using

screws removed in step 2.

10. Leaving a minimum of 3 in.

(7.6 cm) of slack, route the

power supply through the hole

in the alternate junction box

cover and secure with a wire

clamp (not supplied).

11. Connect the black wire (live)

from the unit to the black wire

from the power supply using

one of the wire connectors

removed in step 5 (Figure 5).

12. Connect the white wire (neu-

tral) from the unit to the white

wire from the power supply us-

ing the second wire connector

from step 5 (Figure 5).

13. Attach green grounding wire

to hard wire cover cover with

provided grounding screw.

Place wire in-between screw

and lock washer and tighten.

14. Reposition the electrical box

cover over the wires and con-

nectors and attach to re-

place chassis using the screw

removed in step 3.

15. Carefully reinsert partially

reective glass into replace

forward and lift off. (Figure 3)

4. Remove the 4 screws that

fasten the acrylic media tray

and the 2 screws that attach

the metal tray to the unit. The

metal tray cannot be removed

but will now allow the ability to

remove the electrical box.

5. Remove the Phillips screw to

release the electrical box cov-

er in the bottom, right corner of

the replace (Figure 5).

6. Carefully slide the electrical

box to the right to release the

securing tabs, as wires are fed

through the strain reliefs on

the cover and are connected

within.

7. Unscrew the two wire connec-

tors inside the electrical box

and separate the wires (Figure

6).

8. Pull the junction box and

power cord out the front of the

replace.

Hole for

Ground Screw

Andere Handbücher für Prism BLF5051

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex ELTHAM ETM20-AU Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3215 Bedienungsanleitung

Dimplex

Dimplex KTN20-AU Bedienungsanleitung

Dimplex

Dimplex DFP15-1134NG Bedienungsanleitung

Dimplex

Dimplex Ignite XLF50 Bedienungsanleitung

Dimplex

Dimplex ADG20BN Benutzerhandbuch

Dimplex

Dimplex BF8000ST Bedienungsanleitung

Dimplex

Dimplex DF3020-EU Bedienungsanleitung

Dimplex

Dimplex WINSLOW SWM3520 Bedienungsanleitung

Dimplex

Dimplex DFI2309 Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3015 Bedienungsanleitung

Dimplex

Dimplex Adagio Bedienungsanleitung

Dimplex

Dimplex Brayford BFD20E Bedienungsanleitung

Dimplex

Dimplex THWG XLF50 Bedienungsanleitung

Dimplex

Dimplex BLF74 Bedienungsanleitung

Dimplex

Dimplex DF2608 Bedienungsanleitung

Dimplex

Dimplex SP420 Bedienungsanleitung

Dimplex

Dimplex BF SERIES Bedienungsanleitung

Dimplex

Dimplex HDN20-EU Bedienungsanleitung

Dimplex

Dimplex EF3003 Bedienungsanleitung

Dimplex

Dimplex Revillusion RBF24DLX Bedienungsanleitung

Dimplex

Dimplex Winchester WIN28E Bedienungsanleitung

Dimplex

Dimplex GDS28L8-1941WE Bedienungsanleitung

Dimplex

Dimplex Crestmore CRS20 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung