Dimplex VCX1525 Bedienungsanleitung

Owner’s Manual

Model

VCX1525

VCX1525-WH

To view the full line of Dimplex products, please visit

www.dimplex.com

7209350100R05

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair this

replace.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures

and techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .................3

IMPORTANT INSTRUCTIONS ...............4

Fireplace Installation .......................7

Operation ...............................14

Maintenance.............................16

Warranty ...............................18

Replacement Parts ........................20

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result

in a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the model and

serial number labels of your replace.

Model Number

Plate

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

S E R IAL No.

MODE L

MOD.

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

①Read all instructions before

using the Convex In-Stud re-

place.

②The heater is hot when in use.

To avoid burns, do not let bare

skin touch hot surfaces. The trim

around the heater outlet becomes

hot during heater operation.

Keep combustible materials, such

as furniture, pillows, bedding,

papers, clothes, and curtains at

least three (3) feet (0.9 m) from

the front of the unit and keep

them away from the sides and

rear.

③Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④Always unplug the fireplace

when not in use.

⑤Do not operate any heater

after it malfunctions. Disconnect

power at the service panel and

have the heater inspected by a

reputable electrician before reus-

IMPORTANT INSTRUCTIONS

ing.

⑥ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at 1-888-346-7539.

⑦Do not use outdoors.

⑧Never locate heater where it

may fall into a bathtub or other

water container.

⑨Do not run the cord under

carpeting (for units supplied with

a cord). Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑩To disconnect the unit, turn

the controls off, and then remove

the plug from the outlet or switch

off at main power supply panel if

the unit is hard wired.

⑪Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑫ To prevent a possible re, do

not block air intake or exhaust in

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

any manner.

⑬All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable liq-

uids are used or stored.

⑭ Do not modify the replace.

Use it only as described in this

manual. Any other use not rec-

ommended by the manufacturer

may cause re, electric shock or

injury to persons.

⑮This unit may have a polar-

ized plug (one blade is wider than

the other). The plug will t in a

polarized outlet only one way. If

the plug does not t fully in the

outlet, reverse the plug. If it still

does not t, contact a qualied

electrician to install the proper

outlet.

⑯ Always plug heaters directly

into a wall outlet/receptacle.

Never use with an extension cord

or relocatable power tap (outlet/

power strip).

⑰Do not burn wood or other

materials in the replace.

⑱Do not strike the glass front.

⑲ Always use a certied electri-

cian for build-in hard-wired instal-

lation.

⑳Always use properly ground-

ed, fused and polarized outlets.

㉑Disconnect all main power

supply (unplug the unit or switch

off at main service panel) before

performing any cleaning, mainte-

nance or relocation of the unit.

㉒ Do not operate the replace

without the glass assembly and/or

frame.

㉓When transporting or storing

the unit and cord, keep in a dry

place, free from excessive vibra-

tion and store so as to avoid dam-

age.

㉔Do not put combustible mate-

rial, liquid, or small articles such

as sand inside glass assembly.

6 www.dimplex.com

IMPORTANT INSTRUCTIONS

WARNING: Remote control

contains small batteries. Keep away

from children. If swallowed, seek

medical attention immediately.

WARNING: Do not install battery

backwards, charge, put in re or mix

with used or other battery types - may

explode or leak causing injury.

!NOTE: Changes or modications

not expressly approved by the party

responsible for compliance could

void user's authority to operate the

equipment.

CAUTION: This equipment has

been tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC

Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and

on, the user is encouraged to try to

correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between

the equipment and the receiver.

• Connect the equipment into an

outlet on a circuit different from

that to which the receiver is

connected.

• Consult the dealer or an

experienced radio/TV technician

for help.

Operation is subject to the following

two conditions: (1) this device may

not cause interference and (2) this

device must accept any interference,

including interference that may cause

undesired operation of the device.

Fireplace Installation

WARNING: Ensure the power

cord is not installed so that it is

pinched or against a sharp edge

and ensure that the power cord is

stored or secured to avoid tripping

or snagging to reduce the risk

of re, electric shock or injury to

persons.

WARNING: Construction

and electrical outlet wiring must

comply with local building codes

and other applicable regulations

to reduce the risk of re, electric

shock and injury to persons.

WARNING: Do not attempt

to wire your own new outlets or

circuits. To reduce the risk of re,

electric shock or injury to persons,

always use a licensed electrician.

WARNING: To reduce the risk

of re, do not store or use gaso-

line or other ammable vapors or

liquids in the vicinity of the heater.

!NOTE: A 15amp, 120-volt cir-

cuit is required. A dedicated cir-

cuit is preferred but not essential

in all cases. A dedicated circuit

will be required if, after installa-

tion, the circuit breaker trips or

the fuse blows on a regular basis

when the heater is operating. Ad-

ditional appliances on the same

circuit may exceed the current

rating of the circuit breaker.

WARNING: The Convex In

Stud replace is wall mount-

able and can be built in a wall

space 16" (406 mm) over-cen-

ter between 2” (51 mm) x 4”

(102 mm) wall studs. Follow

the installation instructions for

either wall mount or built-in

mounting; failure to do so may

cause damage or injury.

CAUTION: High temperature,

risk of re, keep electrical

cords, drapery, furnishings,

and other combustibles at

least 3 feet (0.9 m) from the

front of the heater.

Wall Mounting Instructions

1. Leave the glass assembly un-

installed until step 10.

2. Select a location for the re-

place, preferably above an

electrical outlet and there

must be at least one wall stud

behind for the replace to

mount onto. The bottom of

the unit must be a minimum

of 14" (356 mm) above the

oor (mounting holes 29¾"

(0.75 m) minimum above the

oor) (Figure 2).

Access to the electrical outlet

8 www.dimplex.com

must be maintained. Ensure the

installation meets the national and

state/provincial electrical codes.

!NOTE: It is recommended

that the bottom of the unit not be

mounted higher than 48" (1.22

m) from the ground to maintain

an optimized viewing angle of the

ame.

CAUTION: The replace must

be mounted at two points, one of

which must be on a wall stud.

WARNING: High tempera-

tures may be generated under

certain abnormal conditions. Do

not partially or fully cover or ob-

struct the bottom of this heater.

Bottom of unit must be a mini-

mum of 14" (356 mm) above the

oor or any surface such as a ta-

bletop to ensure adequate space

for heat exhaust from the bottom

of the replace (Figure 3).

3. With a wall stud nder, locate

the center of the wall stud,

drive a wood screw into the

stud and leave approximately

⅛" (3 mm) exposed threads

for the replace to hang on.

4. The second mounting point

should be picked such that it

is farthest (to the left or right)

relative to the rst one among

Fireplace Installation

the seven (7) keyholes (A to

G shown in Figure 2) on the

replace for wall mounting,

these keyholes are 2" (51

mm) apart. For example, if

you plan to use hole B as

the rst mounting hole, the

second mounting hole must

be G.

Other available combinations

are A-G, C-G, A-F, A-E, A-D

and D-G.

5. Mark the second mounting

Figure 2

ABC D E F G

29¾” - 75¾”

(0.75 - 1.92m)

14” - 48”

(0.36 - 1.22m)

Fireplace Installation

screw location; ensure that it

is level with the rst with the

help of the provided bubble

level and the replace itself.

Screw the threaded drywall

anchor in the drywall with a

Philip’s head screwdriver until

the head is at against the

wall surface.

Caution should be taken

when using a power tool to

install a threaded drywall an-

chor as the drywall may dis-

tort, tear or slightly buckle as

a result of over-torque.

6. With a Philip’s head screw

driver, screw the drywall an-

chor screw into the drywall

anchor already in the wall,

leave ⅛" (3 mm) exposed

Figure 3

Heat Exhaust

threads for mounting the re-

place.

7. With the glass assembly tak-

en off, mount the rebox onto

the two mounting screws.

8. Mark position of hole “H”.

9. Remove replace from wall.

10. Install drywall anchor into dry-

wall at marked position.

11. With the glass assembly off,

mount the replace onto the

two mounted screws.

12. Tighten both mounting screws

with a screwdriver. Be careful

not to over tighten the screws

mated with the drywall an-

chor.

13. Secure Philip’s screw into

drywall anchor, already in the

wall (H).

14. Open the bag of pebbles and

gently pour through top open-

ing of front glass assembly.

15. Install glass assembly as

shown in Figure 4.

Built-In Instructions

WARNING: The installation of

the replace unit must comply

with the applicable local and/or

national electrical codes and

utility requirements. This in-

10 www.dimplex.com

stallation should be entrusted

to duly qualied personnel

where required by law.

!NOTE: If the desired replace

location is on the interior of an

exterior wall the unit should

only be surface mounted. If a

in-wall or ush mount look is

desired build the interior wall

out into the room.

1. Leave the frame uninstalled

from the replace chassis un-

til step 13.

2. Prepare a wall opening fol-

lowing the dimensions shown

in Figure 5. Note that a 4"

(102 mm) minimum depth

Fireplace Installation

including the thickness of dry

wall is required. Make sure

there is enough clearance for

the cable coming out from the

bottom of the replace.

!NOTE: Where there are close

tolerances involved in wall build-

ing or applications which require

a great degree of precision, we

recommend that the product itself

be used to make the actual mea-

surements for the wall opening.

Dimplex North America will not

be responsible for inaccuracies

in the design or manufacture of

enclosures.

WARNING: Ensure method of

Ensure Glass

Assembly

brackets engage

hooks on replace

by sliding Glass

Assembly towards

replace and then

down Secure Glass

Assembly with the

four (4) supplied

self-tapping screws

Figure 4

Andere Handbücher für VCX1525

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex Mini Mozart Deluxe Bedienungsanleitung

Dimplex

Dimplex BAR20-AU Bedienungsanleitung

Dimplex

Dimplex DF1870L Bedienungsanleitung

Dimplex

Dimplex ALBANY ABN 15 Bedienungsanleitung

Dimplex

Dimplex TFA36E Bedienungsanleitung

Dimplex

Dimplex BLF74-EU Bedienungsanleitung

Dimplex

Dimplex DF3003 Bedienungsanleitung

Dimplex

Dimplex EF2570G Bedienungsanleitung

Dimplex

Dimplex VIVALDI DE LUXE Bedienungsanleitung

Dimplex

Dimplex BFSL33 Bedienungsanleitung

Dimplex

Dimplex Juneau XL Bedienungsanleitung

Dimplex

Dimplex DF2024 Bedienungsanleitung

Dimplex

Dimplex HAR20 Bedienungsanleitung

Dimplex

Dimplex Opti-myst RTOPW20 E Bedienungsanleitung

Dimplex

Dimplex CHT20LE Bedienungsanleitung

Dimplex

Dimplex DF2524G Bedienungsanleitung

Dimplex

Dimplex DF3003 Bedienungsanleitung

Dimplex

Dimplex BLF74 Bauanleitung

Dimplex

Dimplex EWMC-CC-SS Bedienungsanleitung

Dimplex

Dimplex VF5452L Bedienungsanleitung

Dimplex

Dimplex SP620 Bedienungsanleitung

Dimplex

Dimplex BF42ST-230 Bedienungsanleitung

Dimplex

Dimplex ENG56-400 Technisches Handbuch

Dimplex

Dimplex X1B Black Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung