Dimplex WRCPF-KIT Bedienungsanleitung

Owner’s Manual

Model

WRCPF-KIT

7209110100R03

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this device. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures

and techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations . . . . . . . . . . . . 3

Product Overview.....................4

Receiver Installation (BF units only) ......5

Wall Control Installation ...............7

Initialization ........................14

Operation ..........................15

Warranty ..........................20

Welcome & Congratulations

Thank you and congratulations for choosing to purchase a Wall

Switch Remote Control Kit from Dimplex, the world leader in electric

replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in a

possible electric shock, re hazard and will void the warranty.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

4 www.dimplex.com

Product Overview

The Wall Switch Remote Control

Kit is designed to work with

the following Dimplex electric

replaces:

BF33STP•

BF33DXP•

BF39STP•

BF39DXP•

BF45DXP•

BFSL33•

BLF50•

DF3033ST•

DFG3033BLK•

For the BF units, mentioned

above, follow the Remote

Receiver control installation

instructions starting on page 5.

For replace models BFSL33,

BLF50, DF3033ST and

DFG3033, the pre-installed

remote receiver in these models

is compatible with the Wall

Switch Remote Control. The

Remote Receiver and bracket

contained in this kit will not be

required, proceed directly to the

Wall Control Installation on page

!NOTE: This equipment has been

tested and found to comply with

the limits for Class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

can radiate radio frequency energy

and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

· Reorient or relocate the receiving

antenna.

· Increase the separation between the

equipment and the receiver.

· Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

· Consult the dealer or an experienced

radio/TV technician for help.

Operation is subject to the following

two conditions: (1) this device may not

cause interference and; (2) this device

must accept any interference, including

interference that may cause undesired

operation of the device.

Receiver Installation (BF units only)

Open steel curtain (remove1.

glass doors if applicable).

Remove two (2) screws on log2.

grate and remove log grate

(Figure 1).

Locate and remove the two (2)4.

screws on the manual control

bracket (Figure 3). Remove

the bracket.

Locate and depress the5.

mounting tabs on the plug

connector and remove the

manual control bracket from

replace (Figure 3).

Figure 1

Manual Controls

Screws

Pull front edge of plastic3.

ember bed grate up and

forward until rear tab releases

from the ledge located at

the bottom of the partially

reective glass (Figure 2).

!NOTE: Log set ts tightly into

rebox, some force may be

necessary to remove.

Figure 2

Back

ledge

Log

ember

bed

Rear

tab Front

edge

Side section

Figure 3

Mounting

tabs

Plug

connector

Manual controls

Screw locations

6 www.dimplex.com

Locate the plastic 9-pin plug6.

in the bottom corner of the

replace where the manual

controls were plugged in to.

Insert the plug connector from7.

the remote control bracket

(Figure 4) into plastic plug

inside the replace.

ledge (Figure 2) and the logs

are resting against the partially

reective glass.

Replace log grate using two11.

(2) screws previously removed

in step 2.

Run black antenna wire under8.

remote bracket and ensure

all wiring is placed such that

it does not interfere with re-

assembly.

Install the two (2) screws9.

removed in step 4 into the

remote control bracket and

attach it to the replace.

Replace the log set by10.

inserting front edge and

pushing the back down until

rear tab snaps under back

Figure 4

Remote Control

Plug

Connector

Antenna

Receiver Installation (BF units only)

Wall Control Installation

!NOTE: All electrical wiring

must comply with all national

and local electrical codes

and regulations. Always

use a qualied and licensed

electrician should you have

any questions or concerns for

all wiring work.

!NOTE: The Wall Switch

Remote Control is made

to t standard Decora

style faceplates. Due to

material inconsistencies of

individual faceplates, it may

be necessary to remove the

faceplate for operations such

as changing batteries.

Site Selection for

Installation

Although this Wall Switch Remote

Control can operate on battery

power or by hard wire installation,

a convenient and accessible

location should be chosen. The

range of the Wall Switch Remote

Control is approximately 50 feet

(15 m).

Installation requires the use of a

standard device box and should

the hard wire installation method

be chosen, a location near an

available 24V~ power source

should be considered.

WARNING: Electrocution or

other bodily harm and property

damage can occur if a live

wire is touched or damaged

during installation. Always

consult electrical schematics

for the installation location of

all wiring or consult a qualied

and licensed electrician before

you begin.

Installation

Required Tools and Hardware:

Flat head screwdriver•

Wire cutters / strippers•

Two (2) wire nuts for 22 AWG•

wire

Standard wall device box with•

minimum depth of 2.5 inches

(6.35 cm)

24V~ Power supply (for hard•

wired power installation if

applicable)

Battery Powered Installation

1. Remove the Wall Switch

Remote Control and

installation hardware from its

package.

8 www.dimplex.com

Figure 5 Outer

Housing

Controller

2. Release the Controller from

its Outer Housing by pushing

the front face into the Outer

Housing until you hear a click.

This will release the push-

lock latches and allow the

Controller to be removed from

the Outer Housing (Figure 5).

4. Replace the battery

compartment cover.

5. Reinsert the Controller back

into the Outer Housing by

realigning the tracks on the top

and bottom of the unit with

the guides inside the Outer

Housing. Push the Controller

in until you hear the push-

lock latches click (Figure 8).

6. Slide the Controller and

Outer Housing assembly into

a standard device box and

fasten with the two (2) at

Wall Control Installation

3. Open the Battery Compartment

as shown in Figure 6 and

remove the Insulating Strip as

shown in Figure 7.

Figure 6

Battery

Compartment

Figure 7

Insulating

Strip

Wall Control Installation

to complete the installation

and to blend the installation in

with your choice of decor.

Hard Wired Power Supplied

Installation

Before starting this installation,

it is helpful to initialize the Wall

Switch Remote Control with your

rebox (see Initialization section).

You should have the following

items ready and prepared:

Installed standard wall device•

box with a minimum depth of

2.5 inch (6.35 cm).

A 24V~ power source leading•

to the device box. Possible

sources could be a 24V~

doorbell circuit or a Class 2

24V~ transformer.

The 24V~ wire leads coming•

into the device box should have

between 4 and 6 inches (10-15

cm) of slack left inside the box

to allow for ease of installation

and/or servicing.

You may also leave the•

supplied AAA batteries in the

Controller. There is an internal

electronic bypass that will draw

on the hard wired power source

before the batteries.

Figure 8

Outer

Housing

Controller

Guides

Tracks

Figure 9

Controller

Flat head screws

(supplied)

Wall Box

Outer Housing

head screws (supplied) as

shown in Figure 9.

7. Attach your choice of Decora

style faceplate (not supplied)

10 www.dimplex.com

Wall Control Installation

1. Unpack the Wall Switch

Remote Control and all

hardware from its package.

2. Release the Controller from

its Outer Housing by pushing

the front face into the Outer

Housing until you hear a click.

This will release the push-

lock latches and allow the

Controller to be removed from

the Outer Housing (Figure 5).

3. Push the wire lead storage

compartment cover on the

back of the Control towards

the right (as shown), and

remove (Figure 10).

Figure 10

4. Uncoil the two wire leads and

feed each of them through one

of the two holes located on the

wire lead storage compartment

cover (make sure orientation is

as shown as in Figure 11).

Figure 11

5. Replace the wire lead storage

compartment cover on the

Controller with wire leads fed

through and exposed.

6. Feed the two wire leads from

the Controller through the two

holes in the back of the Outer

Housing as shown in Figure 12.

7. Gently pull the wire leads

through while pushing the

Controller into the Outer

Housing until you hear the push

lock latches click, locking the

Controller in place (Figure 13).

Andere Handbücher für WRCPF-KIT

Inhaltsverzeichnis

Andere Dimplex Fernbedienung Handbücher

Dimplex

Dimplex CX-MPC Bedienungsanleitung

Dimplex

Dimplex DPCRWS Series Bedienungsanleitung

Dimplex

Dimplex DPCRWS Series Bedienungsanleitung

Dimplex

Dimplex Integrated On/Off Remote Bedienungsanleitung

Dimplex

Dimplex MULTIFIRE DF3215 Bedienungsanleitung

Dimplex

Dimplex RC3215 Bedienungsanleitung

Dimplex

Dimplex Multi-function Remote Control Bedienungsanleitung

Dimplex

Dimplex Midline Remote Bedienungsanleitung

Dimplex

Dimplex WRCPF-KIT Bedienungsanleitung

Dimplex

Dimplex BFRC-KIT Bedienungsanleitung

Dimplex

Dimplex 7206620100R02 Bedienungsanleitung

Dimplex

Dimplex DPCRWS Series Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung