Directed Electronics AutoCommand 25622 Kurzanleitung

MMooddeell2255662222

➤

OOwwnneerr’’ss//IInnssttaallllaattiioonnGGuuiiddee

lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy

Directed Electronics (hereinafter "Directed") promises to the original purchaser to repair

or replace with a comparable reconditioned Directed remote start unit if this Directed

remote start unit (hereinafter "Unit"), excluding without limitation, any remote trans-

mitters or associated accessories, proves defective in materials or workmanship under nor-

mal use for the life of the vehicle which the Unit is originally installed. During this peri-

od, so long as the Unit remained installed in the original vehicle, Directed will at its

option, repair or replace this Unit if it is proved defective in workmanship or material

PROVIDED the Unit is returned to Directed's warranty department at One Viper Way,

Vista, CA 92081, along with $20 postage and handling fee, a bill of sale or other dated

proof of purchase bearing the following information: Date of purchase, name and loca-

tion of the merchant who sold the Unit, and product description. This warranty does not

cover labor costs for the removal or reinstallation of the Unit. This warranty is non-trans-

ferable and does not apply to any Unit that has been modified or used in a manner con-

trary to its intended purpose, and this warranty does not cover damage to any Unit caused

by installation or removal of the Unit. This warranty is void if the Unit has been dam-

aged by accident or unreasonable use, neglect, improper service or other causes not aris-

ing out of defects in materials or workmanship. Directed makes no warranty against theft

of a vehicle or its contents.

THE FOREGOING WARRANTY IS THE EXCLUSIVE PRODUCT WARRANTY,

OTHERWISE, ALL WARRANTIES INCLUDING BUT NOT LIMITED TO

EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MER-

CHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY

EXCLUDED AND DISCLAIMED TO THE MAXIMUM EXTENT ALLOWED BY

LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON

TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF

THE PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY

AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEAL-

ERS OR INSTALLERS. SOME STATES DO NOT ALLOW THE LIMITATION ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION

MAY NOT APPLY TO YOU.

LIMITATION OF DAMAGES AND LIABILITY. CONSUMER'S REMEDY IS LIM-

ITED TO REPAIR OR REPLACEMENT OF THE UNIT, AND IN NO EVENT

SHALL DIRECTED'S LIABILITY EXCEED THE PURCHASE PRICE OF THE

UNIT. IN ANY EVENT, DIRECTED SHALL NOT BE LIABLE FOR ANY DAM-

AGES INCLUDING, BUT NOT LIMITED TO, ANY DIRECT, INDIRECT, INCI-

DENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, LOST

PROFITS, LOST SAVINGS, OR, TO THE EXTENT ALLOWED BY APPLICABLE

LAW, DAMAGES RESULTING FROM DEATH OR INJURY ARISING OUT OF

OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR

INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO

NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION

MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT

ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE

RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO

COUNTY, CALIFORNIA.

IIMMPPOORRTTAANNTTNNOOTTEE::

This product warranty is automatically void if its date code or serial number is defaced,

missing, or altered.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤Date of purchase

➤Authorized dealer's company name and address

➤Item number

ttaabblleeooffccoonntteennttss

lliimmiitteeddlliiffeettiimmeeccoonnssuummeerrwwaarrrraannttyy................................................................................ii

IInnssttaallllGGuuiiddee........................................................................

........................................33

what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

installation tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

WWiirriinnggQQuuiicckkRReeffeerreenncceeGGuuiiddee...........................

.........................................................77

H1 Harness - 6 pin connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

H2 Harness - 6 pin connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

relay heavy gauge wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 1, Heavy Gauge Wire Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 2, H1, Main Harness Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 3, H2 Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Step 4, Immobilizer Bypass Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Step 5, Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Remote Start Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Testing the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

OOwwnneerr’’ssGGuuiiddee..........................

................................................................................4444

Remote Start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

NNootteess..........

................................................................................................................5522

qquuiicckkrreeffeerreenncceegguuiiddee::...............................................................

.................................5533

Install Guide

what is included

Control Module

6-Pin Main H1 Harness

6-Pin H2 Secondary Harness

Heavy Gauge Wires

Crash code card

Combination Momentary Switch and LED

Hood Pin Switch

Hardware Kit

Additional parts may be required (such as relays or bypass).

installation tools

Digital Multi-Meter

Drill

1/4Drill Bit (for hood pin switch)

Screwdrivers (Phillips and Flathead)

Wire Stripper

Solder Iron

Electrical Tape

Pliers

Crimping Tool

note: The installation tools listed above may be

optional and those required will vary depending on

your vehicle.

important information

Congratulations on the purchase of your remote start system. This

system is designed to integrate with your existing keyless entry or

alarm system. Properly installed, this system will provide years of

trouble-free operation.

Please take the time to carefully read this User’s Guide in its

entirety prior to installing your system.

You can print additional or replacement copies of this manual

by accessing the Directed web site at

www.autocommand.com.

system maintenance

After the installation is completed the system requires no

specific maintenance.

warning! safety first

The following safety warnings must be observed at all times:

When properly installed, this system can start the vehicle

via input from your existing keyless entry or alarm

system. Therefore, never operate the system in an area

that does not have adequate ventilation. The following

precautions are the sole responsibility of the user;

➜

important! If you are not comfortable working with

electronics or unfamiliar with the tools required,

please contact your local dealer for advice or ask to

have the remote start professionally installed to avoid

costly damages. Failure to properly install the remote

starter may result in property damage, personal injury,

or both.

however, the following recommendations should be made

to all users of this system:

1. Never operate the system in an enclosed or partially

enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed

area or when having the vehicle serviced, the remote

start system must be disabled by placing the system

into Valet Mode.

3. It is the user's sole responsibility to properly handle

and keep out of reach from children all remote

control units to assure that the system does not

unintentionally remote start the vehicle.

4. THE USER MUST INSTALL A CARBON MONOXIDE

DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT

TO THE VEHICLE. ALL DOORS LEADING FROM ADJA-

CENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY

ENCLOSED VEHICLE STORAGE AREA MUST AT ALL

TIMES REMAIN CLOSED.

Use of this product in a manner contrary to its intended

mode of operation may result in property damage,

personal injury, or death. Except when performing the

Safety Check outlined in this user’s guide, (1) Never

remotely start the vehicle with the vehicle in gear, and (2)

Never remotely start the vehicle with the keys in the igni-

tion.

After the remote start module has been installed, test the

remote start module in accordance with the Safety Check

outlined in this installation guide. If the vehicle starts

when performing the Neutral Safety Shutdown Circuit

test, the remote start unit has not been properly

installed. The remote start module must be removed or

properly reinstalled so that the vehicle does not start in

gear. OPERATION OF THE REMOTE START MODULE IF THE

VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED

MODE OF OPERATION. OPERATING THE REMOTE START

SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROP-

ERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE

THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE

INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE

HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REIN-

STALLATION COSTS.

Wiring Quick Reference Guide

Heavy Gauge

Wires

BLUE WHITE (+)

YELLOW

PINK

GREEN (+) output to ign/acc2 circuit

MOMENTARY SWITCH

Fused light

flash jumper Black (-)

Heavy guage

ground wire

YELLOW (+/-) parking light output

BROWN/WHITE (-) factory alarm disarm output

VIOLET (-) negative hood pin shutdown output

ORANGE (+) brake input

WHITE/BLACK (-) 400mA status output

RED/WHITE (-) remote start activation

GREEN Tachometer input

BLUE (-) 400mA horn/siren output

RED/BLACK (-) wait-to-start input

YELLOW/GREEN (+) ignition output

BROWN (-) 400mA RAP, Factory Alarm rearm

YELLOW/BROWN (-) 400mA Headlight output

Inhaltsverzeichnis

Andere Directed Electronics Fernstartsystem Handbücher

Directed Electronics

Directed Electronics AutoCommand 41026 Kurzanleitung

Directed Electronics

Directed Electronics SmartStart 5000-series Bedienungsanleitung

Directed Electronics

Directed Electronics AutoCommand 25523T Bedienungsanleitung

Directed Electronics

Directed Electronics PS-4661TWE-FM Bedienungsanleitung

Directed Electronics

Directed Electronics CT-3271 Bedienungsanleitung

Directed Electronics

Directed Electronics Clifford G4203X Bedienungsanleitung

Directed Electronics

Directed Electronics Valet 562T Bedienungsanleitung

Directed Electronics

Directed Electronics BOA 165B Kurzanleitung

Directed Electronics

Directed Electronics 440HP Bedienungsanleitung

Directed Electronics

Directed Electronics ProStart CT-3371 Bedienungsanleitung

Directed Electronics

Directed Electronics 5301 Bedienungsanleitung

Directed Electronics

Directed Electronics Valet 561T Bedienungsanleitung

Directed Electronics

Directed Electronics AutoCommand 41027T Kurzanleitung

Directed Electronics

Directed Electronics CLIFFORD 1.3X Bedienungsanleitung

Directed Electronics

Directed Electronics AS-1271 Bedienungsanleitung

Directed Electronics

Directed Electronics AS-1775 Bedienungsanleitung

Directed Electronics

Directed Electronics G4311A-AM15 AM15 Bedienungsanleitung

Directed Electronics

Directed Electronics XK811 Bedienungsanleitung

Directed Electronics

Directed Electronics 991 Bedienungsanleitung

Directed Electronics

Directed Electronics Smart start Bedienungsanleitung

Directed Electronics

Directed Electronics 474A Bedienungsanleitung

Directed Electronics

Directed Electronics 435 Bedienungsanleitung

Directed Electronics

Directed Electronics 5301 Bedienungsanleitung

Directed Electronics

Directed Electronics AVITAL 4603 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch