Directed Electronics AVITAL 4003 Bedienungsanleitung
Model 4003
Remote Start
Owner’s Guide
© 2009 Directed Electronics, Vista, CA
G4003L 2009-04
Contents
Warning! Safety first .........................................................................................2
What is Included ............................................................................................4
Important Information ........................................................................................4
Your Warranty..........................................................................................4
Using Your System ...........................................................................................5
Remote Start.............................................................................................5
Valet Take-Over ........................................................................................6
Starter Anti-Grind Circuitry.........................................................................7
Disabling the Remote Start system ...............................................................7
Programming options.........................................................................................8
Glossary of Terms..............................................................................................9
Quick Reference Guide....................................................................................11
Notes ............................................................................................................12
Notes ............................................................................................................13
Limited Consumer Warranty .............................................................................14
2© 2009 Directed Electronics. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal
from the remote control transmitter. Therefore, never operate the system in an
enclosed area or partially enclosed area without ventilation (such as a garage).
When parking in an enclosed or partially enclosed area or when having the
vehicle serviced, the remote start system must be disabled using the installed
toggle switch. It is the user’s sole responsibility to properly handle and keep out
of reach from children all remote control transmitters to assure that the system
does not unintentionally remote start the vehicle. THE USER MUST INSTALL A
CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJA-
CENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING
AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE
AREA MUST AT ALL TIMES REMAIN CLOSED. These precautions are the sole
responsibility of the user.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. (1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral safety feature of the
vehicle periodically checked, wherein the vehicle must not remotely start while
the car is in gear. This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the product installation
guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.
3
© 2009 Directed Electronics. All rights reserved.
After the remote start module has been installed, contact your authorized dealer
to have him or her test the remote start module by performing the Safety Check
outlined in the product installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit has not been
properly installed. The remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle does not start in gear.
All installations must be performed by an authorized Directed dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERAT-
ING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AU-
THORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR
PAY FOR INSTALLATION OR REINSTALLATION COSTS.
This product is designed for fuel injected, automatic transmission ve-
hicles only. Use of this product in a standard transmission vehicle is
dangerous and contrary to the product's intended use.
4© 2009 Directed Electronics. All rights reserved.
What is Included
The control module•
A push-button programming switch•
Your warranty card•
A shut-down toggle switch•
Important Information
Congratulations on the purchase of your remote start system. This sys-
tem has been designed to provide years of trouble-free operation. By
carefully reading this owner’s guide prior to using your system, you will
maximize the use of this system and its features. Additional or replace-
ment copies of this guide can be printed by accessing the Directed
Electronics internet website at
www.avital.com
➢Your Warranty
Your warranty card must be completely filled out and returned within
10 days of purchase. Your product warranty will not be honored if
your warranty card is not returned. Make sure that you receive the
warranty card from your dealer. You may also register online at:
www.prodregister.com/directed
5
© 2009 Directed Electronics. All rights reserved.
Using Your System
➢Remote Start
This feature allows you to remotely start and run your vehicle for a
programmable period of time. This makes it possible to warm
up the engine, as well as adjust the interior temperature of the ve-
hicle with the climate control system. If interior heating or cooling
is desired, the climate controls must be preset, and the fan blower
must be set to the desired level prior to remote starting the vehicle.
Important!
(1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the
vehicle with the key in the ignition.
To remote start the vehicle:
Activate the auxiliary channel on your Keyless Entry or Security1.
system tied to your remote start system.
Important: See your authorized Directed Dealer for the
programmed number of times required, (1,2 or 3) to
activate the auxiliary channel. The factory setting is 1
pulse.
The parking lights flash to confirm remote start.2.
Once the vehicle has started, the parking lights come on solid. The3.
vehicle runs for the pre-programmed period of time (12, 24, or 60
minutes) or until a shutdown input is triggered. This can be set to
minute increments by your installer.
6© 2009 Directed Electronics. All rights reserved.
When you are ready to drive the vehicle:
Insert the ignition key and turn it to the ON (not the START) posi-1.
tion.
Press the brake pedal. The remote start system shutdowns but the2.
motor continues to run because the ignition has been turned on.
The vehicle now operates as usual.
Note:
If the brake pedal is pressed before the key is in the ON position,
the engine will shut down.
While the vehicle is running during remote start operation, the system
monitors the vehicle and automatically shuts down the engine if the
system receives any of the following Shut-down inputs:
The brake pedal is pressed.•
The hood is opened.•
The shutdown toggle switch is put into the OFF position•
The pre-programmed run time has elapsed.•
The procedure to activate remote start is repeated.•
➢Valet Take-Over
The Valet Take-Over feature allows the vehicle to remain running after
the key has been removed from the ignition. This feature is useful if you
want to exit and lock the vehicle for short periods of time, but would like
to leave the motor running and the climate controls on.
7
© 2009 Directed Electronics. All rights reserved.
To perform Valet Take-Over:
Before turning off the engine, press the auxiliary channel on your1.
Keyless Entry or Security system. (See your authorized Directed
Dealer for the programmed number of times required to activate
remote start.)
Turn the ignition key to the OFF position. (The engine will stay2.
running.)
The engine will run until the pre-programmed time elapses or a3.
shut-down input is received. (See page 9 for complete list of shut-
down inputs.)
Note:
This feature will not work if the brake pedal is being pressed.
➢Starter Anti-Grind Circuitry
Whenever the vehicle is remote started, advanced anti-grind circuitry
prevents the starter from engaging, even if the key is turned to the start
position. This prevents damage to the starter motor if the key is turned to
the start position during remote start operation.
Note:
Anti-grind circuitry only works when the remote start system is
operating the motor and the optional relay is installed.
➢Disabling the Remote Start system
This feature allows your system's remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the shutdown toggle
switch to the OFF position. The switch can be installed in a location of
your choice. Check with your installer for recommended locations.
Location Of Shutdown Switch
_________________________
8© 2009 Directed Electronics. All rights reserved.
Programming options
Programming options control your system's normal operational set-up.
Most options do not require additional parts, but some may require
installation labor.
The following is a list of the programmable options, with the factory
settings in
bold
.
12
• , 24, or 60 minute run time. Your system can be programmed
to allow the vehicle to run for 12, 24, or 60 minutes when remote
started. Can be set up to minute increments by your installer.
Parking lights flashing or•
constant
. Your system can be pro-
grammed to flash or turn on the parking lights constantly during the
entire remote start operation.
Inhaltsverzeichnis
Andere Directed Electronics Fernstartsystem Handbücher
Directed Electronics
Directed Electronics ProStart CT-3371 Bedienungsanleitung
Directed Electronics
Directed Electronics Nissan Kurzanleitung
Directed Electronics
Directed Electronics Python 1401 Bedienungsanleitung
Directed Electronics
Directed Electronics Cyber 110XV Bedienungsanleitung
Directed Electronics
Directed Electronics 7111A Bedienungsanleitung
Directed Electronics
Directed Electronics 4103 Series Bedienungsanleitung
Directed Electronics
Directed Electronics Viper 5501 Bedienungsanleitung
Directed Electronics
Directed Electronics AutoCommand 28623TN Kurzanleitung
Directed Electronics
Directed Electronics 553 Bedienungsanleitung
Directed Electronics
Directed Electronics Smart start Bedienungsanleitung
Directed Electronics
Directed Electronics PS-4461TWE-FM Bedienungsanleitung
Directed Electronics
Directed Electronics Valet 561R Bedienungsanleitung
Directed Electronics
Directed Electronics Valet 562T Bedienungsanleitung
Directed Electronics
Directed Electronics Automate 552 Bedienungsanleitung
Directed Electronics
Directed Electronics 20.7 Bedienungsanleitung
Directed Electronics
Directed Electronics AutoCommand 41027T Kurzanleitung
Directed Electronics
Directed Electronics AutoCommand 40026 Bedienungsanleitung
Directed Electronics
Directed Electronics ProSecurity RK20 Bedienungsanleitung
Directed Electronics
Directed Electronics Viper Bedienungsanleitung
Directed Electronics
Directed Electronics Xpresskit CANMAX400 Bedienungsanleitung
