Directive Systems & Engineering DSE3311LYRMK Bedienungsanleitung

DSE3311LYRMK Rev 3/21

Directive Systems & Engineering

2702 Rodgers Terrace

Haymarket, VA 20169-1628

www.directivesystems.com

703-754-3876

33cm Loop Yagi (Rear Mount), Model DSE3311LYRMK

SPECIFICATIONS

Frequency Range: 902-928 MHz

Number of Elements: 11

Boom Length: 36 inches

Boom diameter: 1 inch

Mast diameter: 2 inches max

Weight: 2 pounds

Connector: Type N female

Gain: 14.5 dBi

3 dB Beamwidth (E Plane): =34°

F/B ratio: >20 dB

Maximum Power: 550 W. average

Stacking Distance:

H Plane 17 inches’vertical

E Plane 19 inches’ horizontal

PARTS LIST

Note: All hardware is Stainless Steel unless otherwise noted.

Anti-Seize Compound - Apply a small amount of the supplied Anti-Seize Compound to the aluminum joints and

to the threads of the U-Bolts to prevent galling.

BEFORE INSTALLING YOUR NEW ANTENNA, PLEASE BE SURE

TO READ THE ENCLOSED WARNING PAMPHLET.

Quantity Description Quantity Description

1 .058" x 1" Drilled boom 1 Boom to Mast "L" Bracket

2 Reflectors 1 & 2 1 2" U-bolt with nuts & lock washers

1 Driven element 1 Saddle

5 Directors 1-5 1 Cable assembly w/connector

3 Directors 6-8 1 Anti-Seize Compound

10 4-40 x 1 1/4” Screw 21" Black End Cap

10 4-40 Lock nut

28-32 x 1 3/8” Screw 1 Assembly Manual

2#8 Hex nut

2#8 Split lock washer

P a g e | 2

DSE3311LYRMK Rev 3/21

CAUTION: While we strive to remove all burrs from all machined parts, there is always the possibility of

sharp edges. We strongly suggest checking the edges and use a fine file, or 400 grit

sandpaper, to remove any burrs that may have been left.

(Can be up or down) (Can be left or right)

ASSEMBLY INSTRUCTIONS

1) Attach loops to the boom with 4-40 screws and lock nuts in proper sequence. Loops go

on the side of the boom marked with an "X". Attach the contents of each bag of elements

before opening the next bag. This will prevent any mix-up of elements on the boom. R2

(Reflector 2 -3/8" wide) is always the first element to be installed with R1 (Reflector 1 -1/4"

wide) always next to the driven element. The connector bracket mounts in the hole with the

circle –No loops mount in this hole! When tightening the nuts on the parasitic elements, be

careful not to torque them too tightly. Snug down the nuts, align the elements and use a

screwdriver for the final tightening. A 1/4-inch nut driver is almost mandatory for this job!

Attach the driven element with the 5/16 nut provided. If only a single antenna is being built, it

doesn't matter which way the loop is oriented. If antennas are to be stacked, see "Instructions

for Stacking Loop Yagis".

2) Attach the boom to mast angle bracket (angle piece) behind the second reflector R2.

The bracket can be installed for either horizontal or vertical polarization. Install U-bolt and

saddle on the bracket.

3) Install the cable assembly through the hole in the driven element mounting bolt. Make

sure the connector bracket is correctly oriented, the bend should be forward for center mount

antennas and rear facing for rear mount antennas. Solder the outer shield to the driven loop

first making sure there is no shield sticking above the large hole in the driven loop. After the

shield is soldered, pass the center conductor through the small hole in the driven loop and

bend the center conductor over and solder (See Assembly Tips below).

We have created a You Tube video, the link of which can be found on our website,

documenting the following steps:

https://youtu.be/ojXbsDv5cvU

P a g e | 3

DSE3311LYRMK Rev 3/21

At this point the connector assembly is facing down, connect a piece of coax and your

SWR bridge or VNA. Pull down on the connector (which will flatten the loop) until you reach

the lowest SWR. If it’s less than 1.5:1 you can stop and make sure the loop doesn’t try to pop

back up, sometimes you have to squeeze the loop with your fingers to make sure it stays in

the shape that gave the best SWR. If you want to further lower the SWR, from the rear of the

antenna, place both your thumbs on the driven loop on either side and gently push it forward

towards D1, you only need to tilt it maybe 3/16” to ¼” and that should drop the SWR to 1.1:1

or less.

Now, GENTLY bend the UT-141 coax after it exits the boom towards the front or rear,

depending on the mounting. You do not want to bend it so tightly that it crushes where it

extends through the bolt. The connector bracket should line up with either D1 or D2 (or the

hole with the circle around it on rear mount antennas), remove that nut and place the

connector bracket on the screw and re-attach the nut. If the bracket doesn’t line up,

sometimes you have to flip the bracket. Loosen the ¾” nut by holding the connector body with

a 9/16” open end wrench. Remove the connector bracket and flip it.

Connector doesn’t fit Front Mount Connector Rear Mount Connector

4) Attach the feedline and tape it to the mast. Seal all connections with silicone RTV or

equivalent.

5) Attach the two black end caps and this will complete the assembly of your

DSE3311LYRMK.

4) The SWR should be 1.5:1 or better. Additional tweaking can be accomplished by

adjusting the distance between the driven element and R1, or by adjusting the shape of the

driven element.

DO NOT, UNDER ANY CIRCUMSTANCES, APPLY ANY TYPE OF SEALANT OR COATING TO THE

DRIVEN ELEMENT, T-ARMS OR CONNECTOR ASSEMBLY, OTHER THAN KRYLON®

CLEAR COAT. ANY OTHER COATING WILL ADVERSELY AFFECT THE SWR AND VOID YOUR

WARRANTY.

P a g e | 4

DSE3311LYRMK Rev 3/21

ASSEMBLY TIPS:

The boom diameter is 1 inch, and it is drilled for 4-40 hardware (no. 33 drill bit). The driven

element hole is enlarged to 5/16 inch. All elements are 0.032-inch-thick and 0.375 inch wide.

Note that the element spacing from D7 on is 5.115 inches. The feed coaxial cable (0.141-inch

semi rigid) goes through the mounting bolt and is soldered to the open ends of the element.

For best match, the driven element should be approximately 4 inches high; this makes it wider

than it is tall. This shape can be adjusted for best match. This antenna is based on work done

by G3JVL.

Soldered Driven Element

P a g e | 5

DSE3311LYRMK Rev 3/21

Note: All dimensions are in inches.

Directive Systems Warranty Policy

All Directive Systems antennas are built with the finest materials available. We take great pride

in building a quality product that will give years of good service and performance. If there is a defect

in materials or workmanship within 90 days of purchase, Directive Systems will repair or replace

the defective part, free of charge, to the original purchaser. DO NOT RETURN ANYTHING

WITHOUT PRIOR AUTHORIZATION FROM DIRECTIVE SYSTEMS. Please contact us either by

phone or email describing the problem and we will work to resolve it.

If, after examining a new antenna you received, you are not satisfied, contact us immediately

for return authorization and refund. ANY ANTENNA THAT HAS BEEN MODIFIED WILL BE

SUBJECT TO A RESTOCKING CHARGE. IF AN ANTENNA IS SO MODIFIED AS TO MAKE IT

UNUSABLE, DIRECTIVE SYSTEMS RESERVES THE RIGHT TO REFUSE TO ACCEPT THE

ANTENNA FOR RETURN.

Inhaltsverzeichnis

Andere Directive Systems & Engineering Antenne Handbücher

Directive Systems & Engineering

Directive Systems & Engineering DS 88-8 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE945LYRMK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE3333LYA Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1245LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1445LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2345LYK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2345LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE3-50 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE945LYRM Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE3319LYAK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2414LYRMK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSEFO144-12XPOL Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1276LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2455LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE3347LYA Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1209LYRM Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2424LYRM Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE3318LYRMK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1445LYB Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE9112LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2045LY Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSEFO146-12 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE1227LYRMK Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch