Test signal. Press the set button, color bar appeared on the screen
and press any key to return to menu(SK- D385IR/M843 only)
2. How to use the jog lever
3. How to control through RS- 485 communication
4. C able array o
①ENTER :
②UP, ③DOWN
④LEFT, ⑤RIGHT
⑥E X T- V IDEO
ㆍPush the lever : Used to access the menu and c onfirm selec tion.
ㆍPush the lever for one second : Used to re turn to previous menu
from the motion detection setting section or privacy mask setting
section.
: Used to move the cursor to up or down.
: Us ed to move the cursor to left or right a nd change
the value.
: E xtra video output terminal for installation.
Plug your test monitor in hear. T he cable is option.
ch the camera with controller's ID, baudrate and protocol
2) Up, Down, Left and right of Jog lever is sa me as Up, Down, Left
and right of RS- 485 controller
3) Enter of Jog lever is the same as menu key or IRIS open key of
RS - 485 controller
4) Return to previous menu from motion detection setting s ection and
privacy mask setting section : Iris close or Iris open for a few second.
Or press the button as Up
1) No impac t & motion alarm type
2) B uilt- in impac t & motion alarm type
(option)
( ption)
1) Mat
Right Down Left successively
5
2
4
3
1
6
E : ORANGE(RX +)
F : WHITE(RX - )
A : BLUE(MOTION)
B : BLACK(GND)
C : GR E EN(IMPACT)
D : BLACK(GND)
E : ORANGE(RX +)
F : WHITE(RX - )
MOTION ALARM
GND
IMPACT ALARM
GND
RX +
RX -
A
B
C
D
E
F
FUNCTION
ㆍIf the camera detected motion when using Motion & Impact
function, outs ide line of motion alarm connect with GND(B).
ㆍIf the camera detect impact, outsie line of impact alarm connect
with GND(D).Outputs of Motion & Impact are 'open collector'.
ㆍMax curre nt & voltage are 200mA and 30V DC.
RS- 485A
RS- 485B
REMARK
No.
※All specification is subject to change without notic e to improve the quality.
Model No.
Image Sensor
TV Type
Sync . Type
Scanning System
Video Output
Gamma Characteristic
OSD
Motion Detection
Impact Detection(option)
White Balace
Privacy Zone
Day & Night
RS- 485 P rotocol
S/N Ratio
Mirror
Backlight
Control Interfac e
Gain Control
Shutter
Te st Illuminance Area
Current C onsumption
LED
Operation Temp.
Preservation Temp.
Dimension
Weight
Resolution
Power Supply
Lens
Revers e polarity protec tion
Effec tive Pixel
Cell Size
Min. Illumination
NTSC / PAL
Internal
2:1 Interlace
1.0 Vp- p(S ync. Negative) Termination 75Ω ± 10 %
γ= 0.45(Adjustable)
Full OSD
ON / OFF S elec table(64 Zone)
ON / OFF Selectable(3 Step : LOW / MIDDLE / HIGH)
ATW / AWC / MANUAL
ON / OFF S electable(4 Zone)
Electronic D&N(AUTO, COLOR, B/W)
PE LC O- D&P
48dB over(AGC OFF)
ON / OFF
DWDR / BLC / HLC / OFF
YE S
Extra Video connec tor for easy installation
Automatic (Adjustable)
1/60~ 1/100,000sec(NTS C), 1/50~ 1/100,000sec (PAL)
Average tes tilluminance by front view
Regulated 12V DC ± 10%
Max. 300mA(at 12V DC)
Fixed focal lens
IR LE D 14EA
- 10 ∼50℃
- 20 ∼60℃
Ø 110 × 80(H)mm
Approx. 230g
700 TV- Line
1/3" S ONY SUPE R HAD CC DⅡ
6.35㎛(H) X 7.4㎛(V)(NTSC)
6.5㎛(H) X 6.25㎛(V)(PAL)
768(H) X 494(V ) PIXEL(NTSC)
752(H) X 582(V) PIXEL(PAL)
0 Lux(15M Range) : LED ON
0.1Lux(F/1.2) : LED OFF
◐SPECIFICATION C olor temperature 2500 ~ 9500°K
Adjust the Red or B lue values to s hift the color
of the object
Move the camera lens toward to white paper
then press the set button to find the optimal
white balance for current environment
Auto day&night switc hing mode
Fixed at c olor(LE D OFF)
Fixed at B/W(LE D ON)
Determines whether to transmit the burst signal
or not in B /W mode
You can select brightness of illumination about
changing the day ↔night mode
You can select the duration time about c haining
the day ↔nightmode
IR L ED OFF/ON and output level adjustable
When IR LED is turned on in B/W, the objects
can be clearly identified due to the function
that decreases screen saturation of objects
within a short distance.
S et a horizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness com-
pensation of four lens' corners(LSC) or not
The LSC level selectable
Adjust Red tone of the image
Adjust Blue tone of the image
Determines whether to use the motion detection
function or not
No display on the screen though movement
is detected
The words 'MOTION' appear on the screen
when movement is detec ted
Motion detection area appear on the screen
when movement is detec ted
Motion detection sensitivity
Set the duration of outs ide alarm. If the way of
display is message, it means display time of
message
Determines whether to use impact detection
function or not and se nsitivity setting
Set the duration of outside alarm and display
time of "IMPACT" message
Dis play each privacy mask or not. Press the
set button to move into the privacy mask
setting s ection, whenever you press the set
button, the mask color is changed. When the
mas k color is red you can adjust the s ize by
up, down, left and right button. When the
mas k color is blue you can s et the position of
mas k by up, down, leftand right button. Press
the set button for a few second to escape
S elect mas k color
Select the camera ID for RS- 485 communication
S elect baud rate
S elect protocol
S elect language
Dis play the camera ID on the screen
ATW
MANUAL
AWC↓
AUTO
COLOR
B&W
OFF, ON
85 ~ 170
50 ~ 135
3 ~ 15
OFF, ON
OFF, ON
0 ~ 50
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
OFF, ON
NONE
MESS AGE
MASK
0 ~ 255
1 ~ 15
OFF, LOW,
MIDDLE, HIGH
1 ~ 15
OFF, ON
1 ~ 255
2400 ~ 9600
ENGLISH, …
OFF, ON
Press the set button to move into the motion detection area
section to setthe 64 areas . Press the set button for a few second
to move out
Press the s et button to s ele ct all area
Press the s et button to remove all a re a
AWB MODE
D&N MODE
LED LE V E L
DYNAMIC IR
MIRROR
SHARPNESS
GAMMA
LSC
R- Y GAIN
B- Y GAIN
MOTION
IMPACT
MASK
1, 2, 3, 4
CAM ID
BAUDRATE
PROTOCOL
LANGUAGE
BURST
DELAY TIME
LSC LEVEL
DISPLAY
SET
WINDOW
ALL SET↓
SENSITIVITY
HOLD TIME
HOLD TIME
EDIT
POSITION
6. PRIVACY
MASK
7. COMMUNI-
CATION
10. EXIT
9. FACTORY
SET
5. MOTION &
IMPACT
4. IMAGE
ADJUST
3. DAY&NIGHT
PE LCO- D, PE LCO - P
MASK COLOR
NAME DISPLAY
BLACK, GRAY…
8. SPEC IAL
2. WHITE
BALANCE
ALLC LE AR↓
COLOR B&W
B&W COLOR
→
→
OFF, LOW, MIDDLE, HIGH
PAT T ERN
GE NERATOR
Press the set button to move into the name setting section. You
can choose the letter by using up and down button and move
next letter by using left and right button. P ress the set button for
a few second to move out
Press the set button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button
※If you change the COMMUNICATION value through RS- 485, you might not
control the camera due to unmatc hed value(If your camera is out of working
due to above reas on, change your controller's value or wait a few minute till
close the menu, itwill be back to previous setting value)
To reset your c amera to factory default condition
Notice : Lens, communic ation and language is not changed
Save the value and then restart
0.45, 0.6, 1, USER
Fixed focal lens or Vari- focal auto iris lens
In case of manual lens s election, adjust the
brightness
In case of DC lens selection, adjust the bright-
ness
Shutter speed auto adjustable
S elect shutter speed manually
Determines that use the AGC function or not
and AGC level s electable(You c an not use the
Auto D&N change mode when AGC is off)
Digital Wide Dynamic Range
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytime and on at night
According to the threshold value, the camera
will recognize as High light or not.
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
BRIGHT
DC LE V EL
HLC THR
MANUAL, DC
0 ~ 100
0 ~ 20
AUTO
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
1. EXPOSURE
1/60(1/50) ~ 1/100,000
Func tion
setting menu S elect menu ContentsSub menu
OFF, LOW, MIDDLE , HIGH
◐FUNCTION SETTING
1. OSD menu structure
DOIRP3000F
