Dji Agras MG-1P Bedienungsanleitung

MG-1P / MG-1P RTK

Quick Start Guide

V1.0

Aircraft(Model: 3WWDSZ-10016/3WWDSZ-10017)

The Agras MG-1P series (MG-1P / MG-1P RTK) aircraft is equipped witha wide-angle FPV camera,

observing the operating environment in front to offer reality references for planning operation area

and flying with obstacle avoidance remotely. The second generation high-precision radar, integrated

the forward, backward and downward altitude stabilization radar modules and obstacle avoidance

radar module, improves its functions of obstacle sensing and terrain following.

The aircraft body, using new structures and materials, is dust-proof, water-proof (IP43 protection

rating, IEC standard 60529) and anti-corrosive.

The MG-1P / MG-1P RTK contains DJI’s dedicated A3 redundancy system with eight-rotor propulsion

redundancy, ensuring safe and stable operation at all times.The MG-1P RTK has a built-in DJI

Onboard D-RTK*, which provides more accurate data for centimeter-level positioning.

●DO NOT obstruct the GNSS module located at the center of the aircraft, as this will reduce the GPS signal strength.

●The MG-1P / MG-1P RTK does not come with a battery. Please purchase the DJI approved battery pack (Model:

MG-12000P).

*ThisshouldbeusedwithaDJIBaseStation(purchasedadditionally)orDJIapprovedNetworkRTKservice. 

23IntakeVent

24PowerPort

25BatteryCompartment

26RadarCable

27RadarModule

28RemoteControllerHolder

29OcuSyncAntenna

30OnboardD-RTKAntennas(for

MG-1PRTKonly)

12MicroUSBPort

13FlowMeterPort

14LandingGear

15PumpCables

16FlowMeter

17DeliveryPumps

18FlowMeterCable

19SprayTank

20AircraftBody

21GNSSModule

22FPVCamera(frontoftheaircraft)

1Propellers

2FrameArms

3Motors

4ESCLED

5Sprinklers

6ReliefValve

7Nozzles

8Hoses

9LinkButton(rearoftheaircraft)

10PumpPorts

11RadarPort

Remote Controller(Model: GL300N)

Fully upgraded remote controller usessecond-generation DJI OcuSync dual-band video downlink

system which has a maximum control distance of up to 3 km. The remote controller is equipped with a

bright, dedicated screen with a built-in brand new DJI MG app. Operation area planning supports

using both the remote controller and aircraft to set waypoints.Smooth turning of the operation route is

added, with the new spraying system, making flight and operation more flexible and efficient. The

remote controllerfeatures a function of multi-drone control with a single remote controller. It can

coordinate up to fivedrones for operation at the same time, which further improves the efficiency of a

single operator. Replaceable batteries and antennas of the remote controller make it easy for daily

operation and maintenance.

For example, the following description uses Mode 2. The left stick controls the aircraft altitude and

heading, while the right stick controls its forward, backward, left and right movements.

Installation

●Threadlocker of medium strength is required for installation. Apply threadlocker when mounting the

6PowerButton

7StatusLED

8BatteryLevelLEDs

9RTHStatusLED

10RTHButton

1Antennas

2DisplayDevice

3Speaker

4ControlSticks

5LanyardAttachment

landing gear, power port module, spray tank, sprinklers and radar module. Ensure threadlocker is

totally dry and solid before flight.

●DO NOT bend the hose in an arc tighter than its minimum bend radius during installation. This is to

avoid creasing, which may compromise the spraying effect.

●Ensure that all installation and connection procedures are completed before powering on the

aircraft.

Mounting the Battery

Insert the battery into the battery compartment from the front of the aircraft. Ensure the battery is

securelymounted and then buckle the belt to the button of the spray tank.

●TheMG-1P/ MG-1P RTK does not come with a battery. Please purchase the DJI approved MG-1S

battery pack (Model: MG-12000P).

●The voltage on the aircraft can reach 50.4 V. Read the battery’s safety guidelines and take

necessary precautions when handling the battery to ensure your own safety.

Fly Safe

It is important to understand some basic flight guidelines, both for your protection and for the safety of

thosearound you.

1. Flying in Open Areas: Do not fly near or above people or animals, or near buildings, power lines

and other obstacles.

2. Maintain Control at All Times: Always keep your hands on the remote controller and maintain

control of your aircraft when it is in flight, even when using intelligent functions such as Intelligent

Operating Planning System, Smart Operation Mode and Smart Return-to-Home.

3. Maintain Line of Sight: Maintain a line of sight to your aircraft at all times and avoid flying behind

buildings or other obstacles that may block your view.

Power Port

Belt

Button

4. Monitor Your Altitude: For the safety of full-sized aircraft and other air traffic, always

fly at altitudes less than 164 feet (50 meters) or according to local laws and

regulations.

Visit https://www.dji.com/flysafe/geo-map for more information on critical safety features such as No

Fly Zones.

Return-to-Home

It is important to take off with a strong GNSS signal to ensure that the Home Point is recorded by the

aircraft.The aircraft will automatically return to the Home Point in the following cases.

Smart RTH: You press the RTH button.

Failsafe RTH*: Remote controller signal is lost.

The aircraft can sense obstacles at a distance up to30 meters, then automatically avoid obstacle

andfly to the Home Point.

* The Failsafe RTH must be enabled in the DJI MG app. If not enabled, the aircraft will hover in place

when remote controllersignal is lost.

Using MG-1P/ MG-1P RTK

Preparing the Flight Battery

Only use DJI approved flight batteries (Model: MG-12000P). Checkbattery level before flying and

charge according to instructions providedby the manufacturer.

Preparing the Remote Controller

Checking Battery Level

Press once to check the battery level.Press once, then again and hold to turn on/off.

Charging the Battery

Press the battery level button once to check the battery level. Fully charge the batteries before

Low →

High

first-time use.

1. Place the battery into the Charging Hub, connect the charger to the Charging Hub, and then

connect the charger to a power outlet (100 - 240V, 50/60Hz).

2. The Charging Hub will intelligently charge batteries in sequence according to battery power levels

from high to low.

3. The Status LED blinks green when charging and turns solid green when fully charged. The buzzer

will begin beeping when charging is complete. Remove the battery or turn off the buzzer to stop it.

Adjusting the Antennas

Tilt the display device on the remote controller to the desired position, then adjust the antennas so

they are facingoutward. The strength of the remote controller signal will fluctuate depending on the

position of the antennas.

Try to keep the aircraft inside the optimal transmission range. If the signal is weak, adjust the

antennas or fly theaircraft closer.

Unfold

Stron Week

Optimal Transmission Range

●Avoid using wireless devices that use the same frequency bands as the remote controller.

Getting Ready for Takeoff

When using your MG-1P / MG-1P RTK for the first time, activate it in the DJI MG app. Your DJI

account andinternet connection are required.

1. Place the aircraft on an open, flat ground with the Aircraft Status Indicator facing towards you.

2. Unfold the propellers and check that they are mounted onto the motors securely. Unfold frame

arms andtighten arm sleeves firmly.

3. Power on the remote controller.

4. Ensure the battery is securely mounted. Connect the battery to the power porton the aircraft.

Flight

Enter the Operation View of the DJI MG app. Ensure that there is a strong GNSS signal and the

operation mode is M mode (Manual). Otherwise the aircraft cannot take off.

Takeoff

Perform the Combination Stick Command (CSC) and then slowly push the throttle stick up to take off.

ThrottleStick

Landing

To land, pull down on the throttle stick down to descend until the aircraft touches the ground. There

are two methods to stop the motors.

1. When the aircraft has landed, push the throttle down and hold. The motors will stop after 3

seconds.

Throttle Stick

2. When the aircraft has landed, push the throttle stick down, then perform the CSC command to stop

the motors. Release both sticks once the motors have stopped.

Throttle Stick

Intelligent Operation Planning System

The remote controller equips a highlighted screen with a built-in Android system, which can run the

DJI MGapp. Measure operation area and obstacles, configure waypoints, and other settings via the

intelligent operationplanning system built-in the app, and the app will produce a flight route according

to the settings. The aircraft canoperate automatically following the flight route.

Specifications

Airframe

Diagonal Wheelbase 1500 mm

Frame Arm Length 619mm

Dimensions

MG-1P:

1460 mm1460 mm578 mm(Frame arms unfolded,

propellers removed)

780 mm780 mm578 mm(Frame arms folded)

MG-1P RTK:

1460 mm×1460 mm×616 mm(Frame arms unfolded,

propellers removed)

780 mm780 mm616 mm(Frame arms folded)

Diameter × Pitch 217 inch

Propeller Weight 58 g

Operating Frequency 2.400 GHz to 2.483 GHz

5.725 GHzto 5.850 GHz (not supported in Japan)

EIRP 2.4 GHz

FCC: ≤26 dBm, CE: ≤20 dBm,SRRC(China): ≤20 dBm,

KCC(Korea): ≤18 dBm, MIC(Japan): ≤18 dBm

5.8 GHz

FCC: ≤26 dBm, CE: ≤14 dBm, SRRC (China): ≤26 dBm,

KCC(Korea): ≤14 dBm

Radar Module

Model RD2412R

Operating Frequency SRRC / CE / FCC: 24.00 GHzto 24.25 GHz

MIC / KCC:24.05 GHzto 24.25 GHz

Power Consumption 12 W

EIRP SRRC: 13 dBm, FCC: 20 dBm, CE: 20 dBm, MIC: 20

dBm, KCC: 20 dBm

Altitude Detection and Stabilization Detection Range: 1 - 30 m

Stabilization Working Range: 1.5 - 3.5 m

IP Rating IP67

Flight Parameters

Total Weight (Excluding battery) MG-1P: 9.7kg, MG-1P RTK: 9.9 kg

Standard Takeoff Weight 23.7 kg

Max Takeoff Weight 24.8 kg(At sea level)

Max Thrust-Weight Ratio 1.71(Takeoff weight of 23.7 kg)

GNSS GPS+GLONASS

Battery DJI approved battery pack (Model: MG-12000P)

Max Power Consumption 6400 W

Hovering Power Consumption 3800 W(Takeoff weight of 23.7 kg)

Hovering Time* 22 min (Takeoff weight of 14 kg with

Hovering Time* 20 min (Takeoff weight of 13.7 kg with a 12000 mAh

battery)

9 min (Takeoff weight of 23.7 kg with a 12000 mAh

battery)

Max Service Ceiling Above Sea

Level

2000 m

Operating Temperature 32° to 104° F (0° to 40° C)

Remote Controller (Model: GL300N)

Model GL300N

Operating Frequency 2.400 GHz to 2.483 GHz

5.725 GHzto 5.850 GHz (not supported in Japan)

Max Transmitting Distance

(unobstructed, free of interference)

3 km

EIRP 2.4 GHz

FCC: ≤26 dBm, CE: ≤20 dBm,SRRC(China): ≤20 dBm,

KCC(Korea): ≤18 dBm, MIC(Japan): ≤18 dBm

5.8 GHz

FCC: ≤26 dBm, CE: ≤14 dBm, SRRC (China): ≤26 dBm,

KCC(Korea): ≤14 dBm

Display Device

5.5 inch screen, 1920×1080, 1000 cd/m2, Android

system, 4G RAM+16G ROM

Operating Temperature 14° to 104° F (-10° to 40° C)

Storage Temperature Less than 3 months: -4° to 113° F (-20° to 45° C)

More than 3 months: 72° to 82° F (22° to 28° C)

Charging Temperature 41° to 104° F (5° to 40° C)

Remote Controller Intelligent Battery

Model WB37-4920mAh-7.6V

Battery Type LiPo battery

Capacity 4920 mAh

Voltage 7.6 V

Energy 37.39 Wh

Charging Temperature 41° to 104° F (5° to 40° C)

Charging Hub

Model WCH2

Input Voltage 17.3 - 26.2 V

Output Voltage and Current 8.7 V,6 A;5 V,2 A

Operating Temperature 41° to 104° F (5° to 40° C)

Andere Handbücher für Agras MG-1P

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere dji Drohne Handbücher

dji

dji Phantom 4 RTK Bedienungsanleitung

dji

dji SPARK Bedienungsanleitung

dji

dji Air 2S Bedienungsanleitung

dji

dji PHANTOM 4 Bedienungsanleitung

dji

dji AVATA Bedienungsanleitung

dji

dji spreading wings s900 Bedienungsanleitung

dji

dji AIR 3 Bedienungsanleitung

dji

dji MAVIC PRO Benutzerhandbuch

dji

dji PHANTOM 4 PRO Bedienungsanleitung

dji

dji INSPIRE 3 Bedienungsanleitung

dji

dji Mavic 2 Enterprise Bedienungsanleitung

dji

dji M1S Bedienungsanleitung

dji

dji Mini 3 Bedienungsanleitung

dji

dji M30 Bedienungsanleitung

dji

dji PHANTOM Bedienungsanleitung

dji

dji MAVIC 2 PRO Bedienungs- und Wartungsanleitung

dji

dji SPARK Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji MATRICE M30 EU Bedienungsanleitung

dji

dji SPARK Bedienungsanleitung

dji

dji INSPIRE 2 Bedienungsanleitung

dji

dji Inspire 1 Pro Bedienungsanleitung

dji

dji P4 MULTISPECTRAL Bedienungsanleitung

dji

dji Phantom 4 RTK Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

MAKE

MAKE Terry Kilby Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

Atlas

Atlas AtlasPRO Bedienungsanleitung

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

Potensic

Potensic D58 Bedienungsanleitung

Arris

Arris M900 Bedienungsanleitung

Storm

Storm DJI Flamewheel F450 RTF Bedienungsanleitung

dji Agras MG-1P Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken