DMP Electronics CellComRT Bedienungsanleitung

InstallatIon GuIde

CellComRT Digital Cellular Communicator

Description

The CellComRT Digital Cellular Communicator provides a fully supervised alarm communication path over the GSM/

GPRS network. The CellComRT is installed remote from the panel enclosure in a supplied plastic housing and can be

powered directly from the XR100 or XR500 Series panel LX header or can be powered from an optional power supply.

What is Included

The CellComRT includes the following:

•

One Remote Cellular Communicator

• One380-400SecureComWirelessSIMCard

• PlasticHousing

• One383RubberDuckAntenna

• OneCELLCOMBATLithiumPolymerRechargeableBattery

Compatibility

The CellComRT is compatible with the XR100, XR100N, XR500,

XR500NandXR500ECommandProcessorsusingsoftwareVersion

203orhigher.TheCellComRToperatesonthepanelLXheader

andcanbeusedwithan1100SeriesWirelessReceiver.

Installation Safety

Ground Yourself Before Handling the Panel! To discharge

static, touch any grounded metal, such as the enclosure,

before touching the panel.

Remove All Power From the Panel! RemoveallACandBatterypowerfromthepanelbeforeinstallingorconnecting

any modules, cards, or wires to the panel.

Bus Connection

TheCellComRTinterfaceswiththeXR100/XR500Seriesusingthepanel’son-boardLX-Busheader(J22).

The

CellComRTcanbemountedupto100feetfromthepanelenclosureusing22AWGwireor250feetusing18AWG

wire.

Harness Connection

Use the following steps to connect the CellComRT to the panel:

1.Installajumperacrosstheheaderpinsnexttotheletter“X”ontheXR100/XR500panel’sJ23header.

Connectthe4-wireharnessfromtheJ22headerontheCellComRTtotheXR100/XR500panel’sLX-Busheader(J22).

3.Afterpower-upoftheCellComRT,brieyresettheXR100/XR500panelusingtheJ16jumpertoactivate

operation.

Installing the CellComRT

Connecting Backup Rechargeable Battery

Observepolarityandconnecttherechargeablebatteryleadconnectortothe2-pinCellComJ4

battery header.

Tamper Switches

The CellComRT is equipped with two tamper switches. One is located inside the housing. The

second tamper is a wall tamper switch.

BeforemountingtheCellComRTunit,followthesesteps

to install the tamper springs:

Place the included tamper springs on the tamper switches. The long tamper spring installs

inside the housing and the short tamper spring installs in the opening in the back of the

CellComRT housing.

2.Withspringinplace,mounttheCellComRTonaatsurfacethatengagesthetamper

spring and closes the tamper.

See Figure 1 for mounting hole locations.

Connecting the Antenna to the CellComRT

AttachtheRubberDuckAntennatotheAntennaSMAConnector(J19)locatedonthetopright

side of the CellComRT. See Figure 2.

CellComRT

Mounting Holes

Antenna

Tamper

Switch

J19

Battery

Transmit LED

SIM Card

Holder

J22

Mounting Screw

Shoulder Washer

Figure 1: CellComRT PCB

Antenna

Ta mper

Switch

J19

Battery

Charge LED

Transmit LED

J16 Reset

J22

CellCom

J4 J25

SIM Card

Holder

Rubber Duck

Antenna

Figure 2: CellComRT

Antenna Installation

Digital Monitoring Products CellCom Installation Guide

Connecting the Optional Auxiliary Power Supply

Use the following steps when connecting an optional

auxiliarypowersupplytotheCellComRT:

1.ConnecttheRedwire(auxiliaryPower)to

thetopCellComRTJ22terminalposition‘R’

andtotheDCpositiveterminal(+)ofthe

powersupply.SeeFigure3.

2.ConnecttheBlackwire(ground)tothe

bottomCellComRTJ22terminalpositionand

totheDCnegativeterminal(-)ofthepower

supply andtotheLXheader(J22)onthe

XR100/XR500Seriespanel.SeeFigure3.

Connecting the Optional Plug-in Transformer

WhenusinganoptionalModel376plug-inDCpowersupply,

mount the CellComRT near a wall outlet. Use the following steps

toconnecttheplug-inpowersupplytotheCellComRT:

1.Removethebarrelconnectorfromthe376powersupply.

2.Connecttheplug-inpowersupplyBlackwirewithWhite

stripestothetopCellComRTJ22terminalposition‘R’.

SeeFigure4.

3.Connecttheplug-inpowersupplysolidBlackwireto

thebottomCellComRTJ22terminalpositionand to the

LXheader(J22)ontheXR100/XR500Seriespanel.See

Figure4.

4.Plugthepowersupplyintoa110VoltACoutletnot

controlled by a switch.

Programming/Activation

Cellular Service is required before using the CellComRT for signal transmission. Using Remote Link panel

communicationprogramming,selectCELLasoneoftheCommunicationpaths.TheCellComRTcomeswithaSIM

cardreadyforactivationwithSecureComWireless,LLC.Moreinformationisavailableatwww.securecomwireless.

comorrefertotheRemoteLinkGuide(LT-0565).Or,useaSIMcardprovidedbytheGPRScarrierofyourchoice.

LED Indicator

The CellComGreenTransmitLEDlightasheswhentransmissionisbeingmadebetweentheCellComRTandthe

panel.

Diagnostics

The XR100/XR500 Series panels provide a Diagnostics function to test Communication integrity and the Cellular

SignalstrengthoftheCellComRT.TouseDiagnostics,resetthepanel,entertheDiagnosticscode2313(DIAG),and

pressCOMMAND.

Communication Status

SelectCOMMSTATUSfromtheDiagnosticsmenu.TheXR100/XR500panelstesttheCellComRTforthefollowing

items:

•CellComOperating •CellularTowerDetected •APN(AccessPointName)Correct

•SIMCardInstalled •SIMCardRegistered/Active •CommunicationPathIntegrity

Cellular Signal

SelectCELLSIGNALfromtheDiagnosticsmenu.TheXR100andXR500Seriespanelstestandindicatethestrength

ofthesignalusingabardisplay.Onebarindicatingaweaksignal.Sevenbarsindicatingastrongsignal.Ifthebars

indicatesaweaksignal,optionstocorrectthisproblemincluderelocatingtheCellComRTassemblyorextendingthe

CellComRTantennacoaxusingaModel381CoaxExtension.

Red—Auxiliary Power

Yellow—Data In

Green—Data Out

To LX Header (J22) on

XR100/XR500 panel

Black—Ground

Battery

Transmit LED

J22

CellComRT

376

DC Plug-in

Power

Supply

Black Wire with

White Stripes

Solid

Black

Wire

Figure 4: Optional Plug-in Transformer Installation

502-12 Power Supply

J2 J3 J5

AC + BAT –+ DC –

Green

LED

Red

LED

Red—Auxiliary Power

Yellow—Data In

Green—Data Out

To LX Header (J22) on

XR100/XR500 panel Black—Ground

Battery

Transmit LED

J22

CellComRT

Figure 3: Optional Auxiliary Power Supply Installation

CellCom Installation Guide Digital Monitoring Products

Rechargeable Battery

TheCellComRTrechargeablebatteryisusedtoprovide24hoursofbackupbatterypowerwhenDCpowerisnot

available.ThebatteryisintendedforbackuppoweronlyandnottooperatetheCellComRTonadailybasis.Ifthe

batteryislow,ornotpluggedintotheJ4batteryconnector,alowbatteryconditionisindicatedbytheCellComRT

Cellular Communicator.

Note:IfremovingtheCellComRTfromservice,disconnectthebackupbatteryfromtheCellComRTJ4connector.

Installing or Replacing the Battery Assembly

Observepolaritywhenpluggingthebatteryconnectorintotheheader.UseonlyDMPModelCELLCOMBAT.

Removing the Battery Assembly

1.DisconnectthebatteryleadconnectorfromtheCellComRTJ4batteryheader.

2.RemovethebatteryPCBfromthethreestandoffsbyunsnappingthetopoftheplasticclips.

3.Properlydisposeoftheusedbattery.

Caution:Riskofre,explosion,andburns.Donotdisassemble,heatabove212°F(100°C),orincinerate.

Properly dispose of used batteries.

Installing the Battery Assembly

1.AlignthethreebatteryPCBstandoffmountingholeswiththestandoffs.SeeFigure5.

2. Snap the battery assembly in place.

3.ObservepolarityandconnectthebatteryleadconnectortotheCellComJ4batteryheader.

Battery Assembly

Standoff

Antenna

Tamper

Switch

J19

Battery

Transmit LED

SIM Card

Holder

CellComRT

J22

Figure 5: Battery Assembly Standoffs

Antenna

Tamper

Switch

J19

Battery

Transmit LED

J4 J25

SIM Card

Holder

CellComRT

J22

Figure 6: CellComRT Assembly

Digital Monitoring Products CellCom Installation Guide

CellCom System Messages

ThefollowingmessagesarecommunicatedtotheDMPSCS-1RreceivertoindicateCellComstatus:

130WARNING:CellCommunicatorBusFailed

COMMUNICATIONSECURITYFEATURE

The communication on the bus between the panel and the cellular communicator has failed while no areas of

the system were armed. This message may originate from both the panel and the cellular communicator as both

monitorthebus.TherestoralmessageisS132.

131ALARM:CellCommunicatorBusFailed

SERVICENOTIFICATIONFEATURE

The communication on the bus between the panel and the cellular communicator has failed while any area of the

system was armed. This message may originate from both the panel and the cellular communicator as both monitor

thebus.TherestoralmessageisS132.

132CellCommunicatorBusRestored

SERVICENOTIFICATIONFEATURE

The communication on the bus between the panel and the cellular communicator has restored. Message is sent

fromthepaneltothereceiverandisarestoralforS130andS131.

133WARNING:CellCommunicatorDCFailed

SERVICENOTIFICATIONFEATURE

The panel has received a message from the cellular communicator that its input DC voltage is missing or low. The

cellularcommunicatorisoperatingfromitsinternalbattery.TherestoralmessageisS134.

134CellCommunicatorDCRestored

SERVICENOTIFICATIONFEATURE

The panel has received a message from the cellular communicator that its input DC voltage has restored. This

messageisarestoralforS133.

135WARNING:CellCommunicatorLowBattery

SERVICENOTIFICATIONFEATURE

The panel has received a message from the cellular communicator that the cellular communicator’s standby

batteryislowormissing.TherestoralmessageisS136.

136CellCommunicatorBatteryRestored

SERVICENOTIFICATIONFEATURE

The panel has received a message from the cellular communicator that the cellular communicator’s standby

batteryhasrestored.ThismessagerestoresS135.

137WARNING:CellCommunicatorTamper

SECURITYFEATURE

Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in

tamper circuit was placed in an open condition while no areas of the system were armed. The restoral message is

S139.

138ALARM:CellCommunicatorTamper

SECURITYFEATURE

Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in

tamper circuit was placed in an open condition while one or more areas of the system were armed. The restoral

messageisS139.

139CellCommunicatorTamperRestored

SECURITYFEATURE

Thepanelhasreceivedamessagefromthecellularcommunicatorthatthecellularcommunicator’sbuilt-in

tampercircuitwasrestoredtoanormalcondition.ThismessageisarestoralforS137andS138.

AllthemessagesabovearecommunicatedbytheXR100/XR500controlpanelexceptS130andS131Cell

CommunicatorBusFailwhichissentbyboththepanelandCellCom.Forcompleteinformation,refertotheHost

CommunicationSpecication(LT-0086).

CellCom Installation Guide Digital Monitoring Products

FCC Information

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:

(1)Thisdevicemaynotcauseharmfulinterference,and

(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.

Changesormodicationsmadebytheuserandnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe

user’s authority to operate the equipment.

NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguarantee

thatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 -Reorientorrelocatethereceivingantenna.

 -Increasetheseparationbetweentheequipmentandreceiver.

 -Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

 -Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Listed Compliance Specications

Commercial Burglary

Forlistedinstallations,theCellComRTmaybeinstalledinthefollowingcongurations:

•Installedanddirectlypoweredfromthecontrolpanel.

•InstalledandpoweredfromaUL603listedpowersupply.

TheadditionalonboardstandbyLithium-Ionbattery,CELLCOMBAT,isconsideredauxiliaryoperationandhasnot

been evaluated by UL.

TheoptionalModel376Plug-inDCPowerSupplyisconsideredauxiliaryoperationandhasnotbeenevaluatedbyUL.

800-641-4282

      

www.dmp.com 2500 North Partnership Boulevard



 

LT-0999 © 1.01 2009 Digital Monitoring Products, Inc.

9112

Compatibility

DMP Command Processor panels XR100, XR100N, XR500,

XR500N,XR500EusingSoftwareVersion203orhigher

Listings and Approvals

FCCPart15andCISPR22

FCCID:MIVGSM0308

IndustryCanadaID:4160A-GSM0308

UnderwritersLaboratories(UL)Listed

ANSI/UL365 PoliceStationConnectBurglarAlarmSystems

ANSI/UL985 HouseholdFireWarningSystemUnits

ANSI/UL1023 HouseholdBurglarAlarmSystemUnits

ANSI/UL1076 ProprietaryBurglarAlarmUnits&Systems

ANSI/UL1610 CentralStationBurglarAlarmUnits

Export Control

 TheCellComRTusesAESencryptionandanyexportbeyond

theUnitedStatesmustbeinaccordancewithExport

AdministrationRegulations.

Specications

PrimaryPower 12VDC

Current Draw

 Standby  21mA

 PeakTransmission200mA

Ordering Information

CellComRT Remote Digital Cellular

Communicator

Accessories

376  DCPlug-inPowerSupply

380-400 Level400SIMCard(1supplied)

381-12 12'CoaxExtension

381-25 25'CoaxExtension

383  RubberDuckAntenna

386  WallMountAntennaBracket

CELLCOMBAT ReplacementRechargeable 

  Batteryassembly

Inhaltsverzeichnis

Andere DMP Electronics Handy Handbücher

DMP Electronics

DMP Electronics 263LTE-V5 Bedienungsanleitung

DMP Electronics

DMP Electronics 263H HSPA+ Montageanleitung

DMP Electronics

DMP Electronics Com Series Administratorhandbuch

DMP Electronics

DMP Electronics 263CSMX Montageanleitung

DMP Electronics

DMP Electronics CellCom LTE Series Bedienungsanleitung

DMP Electronics

DMP Electronics CellCom-LTE-V SERIES Bedienungsanleitung

DMP Electronics

DMP Electronics CellComSLCF Montage- und Bedienungsanleitung

DMP Electronics

DMP Electronics 263LTE Series Bedienungsanleitung

DMP Electronics

DMP Electronics DUALCOM Series Installations- und Betriebsanleitung

DMP Electronics

DMP Electronics 263LTE-FN Bedienungsanleitung

DMP Electronics

DMP Electronics CELLCOMEX Com Series Administratorhandbuch

DMP Electronics

DMP Electronics iComSL Series Installationsanleitung

DMP Electronics

DMP Electronics XR500 SERIES Bedienungsanleitung

DMP Electronics

DMP Electronics CellCom SLC Installations- und Betriebsanleitung

DMP Electronics

DMP Electronics 265HCAN Bedienungsanleitung

DMP Electronics

DMP Electronics CellCom-LTE-V SERIES Installationsanleitung

DMP Electronics

DMP Electronics 464-263H Montageanleitung

DMP Electronics

DMP Electronics 464-263C Montageanleitung

DMP Electronics

DMP Electronics Com Series Administratorhandbuch

DMP Electronics

DMP Electronics 265LTE-V Bedienungsanleitung

DMP Electronics

DMP Electronics 463C Montageanleitung

DMP Electronics

DMP Electronics Com Series Administratorhandbuch

DMP Electronics

DMP Electronics iComSL Bedienungsanleitung

DMP Electronics

DMP Electronics 263LTE-V Bedienungsanleitung

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LG LM-X420QN Bedienungsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

LG LM-K420EMW Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung