DMP Electronics 1135 Series Installationsanleitung

INSTALLATION AND PROGRAMMING GUIDE

1135 Series

Wireless Siren

1135 Series Installation and Programming Guide | Digital Monitoring Products 1

GET STARTED

The 1135 Series Wireless Siren provides up to 110decibels of annunciation. It includes a wall tamper, a cover tamper,

and a Survey LED.

Multiple sirens can be activated simultaneously by the panel using the Trip with Panel Bell option. This option allows

the siren to follow the panel bell output including the bell cuto time.

In addition to these features, the 1135E Wireless Siren communicates with the panel using 128‑bit AES encryption.

What’s Included

▶One 1135 Series Wireless Siren

▶Two 3.0V Lithium CR123 Batteries

▶Hardware Pack

What You’ll Need

▶5/64” (2.0mm) drill bit

▶#2 Phillips screwdriver

Procedure

To install an 1135 Series Siren, this guide walks you through these required steps:

1. Program the panel.

2. Install the batteries.

3. Select a location.

4. Mount the siren.

5. Test the siren.

1135 Series Installation and Programming Guide | Digital Monitoring Products 2

1 Program the Panel

To program the 1135 Series into the panel, select one of the following methods: Choose Method 1 to make the siren

a non‑standard output that follows the panel bell or Method 2 to make the siren a standard output.

A house code must be programmed in the panel’s SYSTEM OPTIONS before programming wireless devices.

Range is 1 ‑ 50.

For 1135E encrypted sirens to communicate with the panel, 1100 ENCRYPTION must be enabled and a passphrase

must be set in SYSTEM OPTIONS programming. An 1135E will operate as a standard 1135 wireless siren if

encryption is not enabled.

To enter panel programming, reset the panel and enter 6653 (PROG) at a keypad. After completing each of the

following steps, press CMD to advance to the next prompt. After you ﬁnish programming, go to STOP and press

CMD to save and exit the Programmer menu. For more information, refer to the appropriate panel programming

guide.

PANEL MODEL VALID OUTPUT NUMBERS

XR Series 450‑474 (slow) or 480‑499 (fast)

XT Series 31‑34 (slow) or 41‑44 (fast)

XTL Series 51‑54 (slow) or 61‑64 (fast)

Table 1: Valid Output Numbers by Panel Model

Method 1: Non-Standard Output (Follow Panel Bell Output)

1. Go to OUTPUT INFO (XR Series) or OUTPUT SETUP (XT and XTL Series).

2. At OUTPUT NO, enter the output number. Refer to Table 1.

3. At OUTPUT NAME, enter a descriptive name for the siren.

4. At SERIAL#, enter the 8‑digit device serial number.

5. At SUPRVSN TIME, enter the supervision time in minutes.

6. Ensure TRIP WITH PANEL BELL is set to YES (default).

7. Go to BELL OPTIONS and set the BELL CUTOFF. Range is 1 ‑ 15 minutes.

Enable Temporal 4 for CO Alarms (1135 Only)

Requires panel ﬁrmware Version 183 or higher with minimum device ﬁrmware Version 107 and Level 103 hardware.

In BELL OPTIONS, ensure CO TYPE is set to the default value4(Temporal4).

Method 2: Standard Output (Standalone)

1. Go to OUTPUT INFO (XR Series) or OUTPUT SETUP (XT and XTL Series).

2. At OUTPUT NO, enter the output number. Refer to Table 1.

3. At OUTPUT NAME, enter a descriptive name for the siren.

4. At SERIAL#, enter the 8‑digit device serial number.

5. At SUPRVSN TIME, enter the supervision time in minutes.

6. At TRIP WITH PANEL BELL, select NO.

2 Install the Batteries

Observe polarity and install both CR123 batteries. For the battery holder location, refer to Figure 1.

1135 Series Installation and Programming Guide | Digital Monitoring Products 3

Select a Location

The 1135 provides a Survey LED capability to allow one

person to conﬁrm communication with the wireless

receiver or panel while the cover is removed.

1. With the cover removed, hold the siren in the

desired location.

2. Press the tamper switch to send data to the panel

and determine if communication is conﬁrmed or

faulty.

Conﬁrmed: If communication is conﬁrmed, for each

press or release of the tamper switch, the LED blinks

immediately on and immediately o. Repeat this test

to conﬁrm ﬁve separate consecutive LED blinks. Any

indication otherwise means proper communication

has not been established.

Faulty: If communication is faulty, the LED remains

on for about 8 seconds or ﬂashes multiple times in

quick succession. Relocate the siren or receiver until

the LED conﬁrms clear communication.

Note: Operating the siren in extreme hot or cold

environments reduces battery life.

Mount the Siren

Mount the siren in a secure location where it is protected from the environment.

The 1135 siren is equipped with a case and wall tamper. When the housing cover is removed, the case tamper

activates and the 1135 sends a tamper trouble to the panel.

A two‑position header is provided to disable the wall tamper. Refer to Figure 1. To disable the wall tamper, place

the jumper over both header pins.

Without Wall Tamper

1. Remove the two locking screws from the housing, then lift o the cover.

2. Ax the siren to the mounting surface:

a. If using screws, thread the supplied #6 screws through the mounting holes and secure the siren to the

surface.

b. If using double‑sided tape, place the tape on the housing base (the side with mounting holes). Remove

the backing from the tape. Holding the sides of the housing, press the siren onto the mounting surface.

3. Place the jumper over both header pins to disable the wall tamper.

4. Place the cover back onto the base, then reinsert and secure the two locking screws.

Figure 1: 1135 Details

Mounting Holes

PCB Snaps

Batteries

DSound Level

Wall Tamper

Case Tamper Switch

Survey LED

TAMPER

SWITCH

SOUNDER

100 dB

WALL

TAMPR DIS

1135 Series Installation and Programming Guide | Digital Monitoring Products 4

Test the Siren

After the sirenhas been installed, test to conﬁrm that it is communicating reliably with the panel. Use the Tech

APP™ or Dealer Admin™ to perform a Wireless Check‑in Test on the system. To perform a Wireless Check‑in Test

from a keypad that is connected to the panel, complete the following steps:

At the keypad, enter 8144 (WALK) and select WLS. If the transmitter fails to check in at the keypad, ensure that it

is wired properly and check for sources of interference such as metal objects and electronic equipment.

With Wall Tamper

When installing the siren with the wall tamper, refer to Figure 2.

1. Remove the two locking screws from the housing, then lift o the cover.

2. Press the top PCB snaps upward to release the PCB, slide it out of the

bottom snaps, then remove it from the housing.

3. Thread one of the supplied #6 screws through the top tamper hole and the

other through the top mounting hole, then secure the siren to the surface.

4. Snap the PCB back into the housing attached to the wall. Place the cover

back onto the base, then reinsert and secure the two locking screws.

Figure 2: Wall Tamper

Installation

ADDITIONAL INFORMATION

Requirements for Listed Installations

▶The siren cannot be mounted with double‑sided tape

▶UL 1610 Central station Burglar Alarm Units: Must be installed With Wall Tamper

▶UL 985 Household Fire Warning System: Must Enable Temporal 4 for CO Alarms

Disable the Wall Tamper

A two‑position header is provided to disable the wall tamper. Refer to Figure 1. To disable the wall tamper, place

the jumper over both header pins.

Change the Sound Level

The siren is equipped with a 100/110 decibel (dB) jumper and a two‑position header to change the decibel output.

The siren is shipped at the 110dB output level with the jumper placed on one pin for storage. If the 100dB setting

is required, place the jumper over both header pins. Refer to Figure 1.

Silence the Sounder

The following panel operations can silence the sounder:

▶BELL OUTPUT (XR150/XR550only)—Program the output in BELL OUTPUT so the sounder turns o at the

BELL CUTOFF time if less than ﬁfteen minutes

▶Disarming—Program the output in ALARM ACTION for the zone that will be disarmed, then set the action

to STEADY

▶OUTPUTS ON/OFF—In the User Menu, select OUTPUTS ON/OFF. Enter the output number and choose

OFF

▶Output followszone condition—Program the output in ALARM ACTION and set the action to FOLLOW.

When thetransmitterzone restores, the output is turned o

1135 Series Installation and Programming Guide | Digital Monitoring Products 5

Status List

For XR Series systems to display wireless output troubles at a keypad, that keypad’s address must be entered in

STATUS LIST > AUX 1 ZONES (Auxiliary 1 Zones).

Output Response Time

Outputs operate with a 3‑second response time when used with the 1135‑W.

Battery Life Expectancy

Battery life expectancy for is 3years when the siren is operated for 5minutes once a month. DMP wireless equipment

uses two‑way communication to extend battery life. To extend battery life further, operate the siren infrequently and

extend supervision time in panel programming. Multiple on/o siren operations and extreme hot or cold environments

reduce battery life.

Replace the Battery

1. Remove the locking screws from the top and bottom of the siren housing.

2. Lift the cover from the bottom to remove it from the base.

3. Remove the old batteries and dispose of them properly. Always replace both batteries at the same time.

4. Install the two CR123 batteries and press into place. Refer to Figure 1 for battery locations.

5. Place the cover back onto the base and secure the housing using the locking screws.

Sensor Reset to Clear LOBAT

Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message. On an LCD keypad,

press and hold 2for two seconds. On a graphic touchscreen keypad, press RESET. Enter your user code, if required.

The keypad displays SENSORS OFF followed by SENSORS ON.

SPECIFICATIONS

Battery Life Expectancy 3 years

Battery Type 3.0 V lithium CR123

Internal Sounder Type Y

Tone Output 100 dBA at 3 ft (1 m)

Frequency Range 905 ‑ 924 MHz

Operating Temperature 32°F to 120°F (0°C to 49°C)

Relative Humidity 85% at 86°F (30°C)

Housing Material Flame retardant ABS

Weight 0.5 lbs (0.23 kg)

Dimensions 4.5 L x 4.5 W x 1.25 H in

(11.4 L x 11.4 W x 3.2 H cm)

PATENTS

▶U.S. Patent No. 7,239,236

CERTIFICATIONS

▶FCC Part 15 ID: CCKPC0123R8

▶Industry Canada: 5251A‑PC0123R8

18205

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-1106 1.06 22184

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

Underwriters Laboratory (UL) Listed

ANSI/UL 1023 Household Burglar Alarm System Units

ANSI/UL 1610 Central Station Burglar Alarm Units

ANSI/UL 985 Household Fire Warning System

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Information

This device complies with Industry Canada License‑exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

Inhaltsverzeichnis

Andere DMP Electronics Sicherheitssystem Handbücher

DMP Electronics

DMP Electronics 1135 Bedienungsanleitung

DMP Electronics

DMP Electronics XR500 SERIES Bedienungsanleitung

DMP Electronics

DMP Electronics DUALCOM Series Installations- und Betriebsanleitung

DMP Electronics

DMP Electronics Thinline 7063 Bedienungsanleitung

DMP Electronics

DMP Electronics XR350 Bedienungsanleitung

DMP Electronics

DMP Electronics Security Command XR20 Bedienungsanleitung

DMP Electronics

DMP Electronics 1135DB Bedienungsanleitung

DMP Electronics

DMP Electronics 1141 Bedienungsanleitung

DMP Electronics

DMP Electronics XR150 series Bedienungsanleitung

DMP Electronics

DMP Electronics CELLCOMSL SERIES Betriebsanleitung

DMP Electronics

DMP Electronics XT30 Series Bedienungsanleitung

DMP Electronics

DMP Electronics 1135 Series Bedienungsanleitung

DMP Electronics

DMP Electronics 265HINT Bedienungsanleitung

DMP Electronics

DMP Electronics 1136 Bedienungsanleitung

DMP Electronics

DMP Electronics 893A Montageanleitung

DMP Electronics

DMP Electronics 1135 Bedienungsanleitung

DMP Electronics

DMP Electronics XTLtouch Bedienungsanleitung

DMP Electronics

DMP Electronics 135 Series Bedienungsanleitung

DMP Electronics

DMP Electronics XR500 SERIES Bedienungsanleitung

DMP Electronics

DMP Electronics XR500 SERIES Bedienungsanleitung

DMP Electronics

DMP Electronics SCS-1R Bedienungsanleitung

DMP Electronics

DMP Electronics 1912XR Technisches Handbuch

DMP Electronics

DMP Electronics iComSL Series Bedienungsanleitung

DMP Electronics

DMP Electronics XTL Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung