DMP Electronics XTLtouch Series Bedienungsanleitung
XTLtouchTM Series Installation Guide
TABLE OF CONTENTS
About the XTLtouch.............. 1
Install the XTLtouch..............2
Wall Mount (XTLtouch)................... 2
Desk Stand (XTLtouchUSB) .......... 2
Wall Mount .............................3
Mount the Backplate ........................ 3
Wire for Power.................................... 5
Desk Stand..............................8
Install the Desk Stand Legs ...........8
Power the XTLtouch.........................9
Additional Information ....... 10
Secondary Power Supply ............... 10
Replace the Battery ........................ 10
Accessories............................12
Transformer......................................... 12
Batteries.............................................. 12
Certifications.........................13
FCC .........................................14
Industry Canada....................16
Digital Monitoring Products | XTLtouch Installation Guide1
ABOUT THE XTLtouch™
The XTLtouch oers flexible features and functionality. It contains an XTLplus
control panel with an integrated graphic touchscreen keypad, providing one
device to control and operate a system. The XTLtouch has an LTE cellular
communicator pre-installed for cellular use. The XTLtouch can be mounted to
a wall or can be used for tabletop use. The XTLtouch provides the following
features:
▶5” graphic touchscreen screen
▶Three-part housing (cover, base, and backplate)
▶On-board proximity reader for DMP, HID, and Farpointe credentials
▶On-board Wi-Fi
▶Z-Wave Plus™ support
▶800 mAh battery backup
▶Two-way communication using 900 MHz frequency hopping spread-
spectrum technology
▶1100 Series Wireless support
INSTALL THE XTLtouch
Wall Mount (XTLtouch)
For wall mount installations, use the included backplate to mount the XTLtouch
to a wall.
Note: Install the XTLtouch near a wall outlet for the plug-in power supply.
The power supply should be located within 100 feet of the XTLtouch using
22 AWG wire.
Desk Stand (XTLtouchUSB)
For desk stand installations, use the included legs for tabletop use.
Digital Monitoring Products | XTLtouch Installation Guide 2
Digital Monitoring Products | XTLtouch Installation Guide3
WALL MOUNT
Mount the Backplate
1. Press the tab and remove the backplate from the XTLtouch.
See Figure 3.
1
Figure 3: Removing the Backplate
Backplate
Tab
Digital Monitoring Products | XTLtouch Installation Guide 4
2. Use the level and the included #6 screws to mount the backplate to the
wall. See Figure 4 for mounting hole locations.
Figure 4: Mounting Hole Locations
Level
Digital Monitoring Products | XTLtouch Installation Guide5
Wire for Power
See Figure 5 for wire routing instructions before wiring the XTLtouch for
power.
1. Connect the XTLtouch +DC terminal to the positive terminal on the
power supply.
2. Connect the XTLtouch -DC terminal to the negative terminal on the
power supply.
3. Plug the power supply into a 120 VAC 60 Hz dedicated outlet that’s
not controlled by a switch.
4. Replace the XTLtouch on the mounted backplate.
5. Insert the included set screw to secure the XTLtouch to the mounted
backplate. See Figure 6.
2
Digital Monitoring Products | XTLtouch Installation Guide 6
- 12V +
Figure 5: Routing Wires
Power Supply
Mounted Backplate
DC terminals
DC terminals
Digital Monitoring Products | XTLtouch Installation Guide7
Figure 6: Securing the XTLtouch
with the Set Screw
Inhaltsverzeichnis
Andere DMP Electronics Touchscreen Handbücher
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
