Dometic CLASSIC RM 2620 Bedienungsanleitung

INSTALLATION AND

OPERATING INSTRUCTIONS

REFRIGERATOR FOR LP-GAS

& ELECTRIC OPERATION

RM2620

RM2820

USA

Corporate Ofﬁ ce

CANADA

Service Ofﬁ ce 2320 Industrial Parkway Elkhart, IN 46515 Dometic Corporation

Dometic Corporation

46 Zatonski, Unit 3

2320 Industrial Pkwy. Brantford, ON N3T 5L8

Elkhart, IN 46516

For Service Center Assistance

CANADA

Phone: 574-294-2511 Call: 800-544-4881 Phone: 519-720-9578

MO-M 0609

825120306

©Dometic Corporation

LaGrange, IN 46761

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. Don’t touch electrical switches.

3. Extinguish any open ﬂ ame.

4. Immediately call your gas supplier.

POUR VOTRE SÉCURITÉ

Si vous sentez une odeur de gaz:

1. Ouvrez les fenêtres.

2. Ne touchez à aucun interrupteur.

3. Éteignez toute ﬂ amme nue.

4. Avertissez immédiatement votre

fournisseur de gaz.

FOR YOUR SAFETY

Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser de l’essence

ni d’autres vapeurs ou liquides inﬂ amma-

bles à proximité de cet appareil ou de tout

autre appareil.

Improper installation, adjustment, altera-

tion, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional

information consult a qualiﬁ ed installer,

service agency or the gas supplier.

WARNING

Une installation, un réglage, une modiﬁ -

cation, une réparation ou un entretien non

conforme aux normes peut entraîner des

blessures ou des dommages matériels.

Lisez attentivement le mode d’emploi

fourni avec l’appareil. Pour obtenir de

l’aide ou des renseignements supplémen-

taires, consultez un installateur ou un

service d’entretien qualiﬁ é ou le fournis-

seur de gaz.

!AVERTISSEMENT

- 3 -

CERTIFICATION AND CODE REQUIREMENTS

. . . . . . .

INSTALLATION INSTRUCTIONS

. . . . . . . . . . . . . . . . . . .

REFRIGERATOR REMOVAL

. . . . . . . . . . . . . . . . . . . . . .

MOUNTING INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . .

REFRIGERATOR

OVERVIEW

. . . . . . . . . . . . . . . . . . . .

OPERATING INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . .

STORAGE COMPARTMENTS

. . . . . . . . . . . . . . . . . . . .

PRODUCT CARE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAINTENANCE & SERVICE

. . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . . .

APPENDIX A - SPARE PARTS

. . . . . . . . . . . . . . . . . . . .

APPENDIX B - REARVIEW EQUIPMENT

. . . . . . . . . . .

APPENDIX C - WIRING DIAGRAM

. . . . . . . . . . . . . . . .

APPENDIX D - CONSUMER SUPPORT

. . . . . . . . . . . .

APPENDIX E - DOMETIC WARRANTY &

MAINTENANCE SCHED

ULE

. . . . . . . . . . . . . . . . . . . . . .

INTRODUCTION

Thank you for entrusting us to supply your new refrigerator which is designed for storage of foods, frozen foods and for making

ice. This manual describes how to install and operate the refrigerator models RM2620 and RM2820. Read the manual carefully

to ensure that you know how to operate the refrigerator safely and correctly. Be aware of possible safety hazards when seeing alert

symbols on the refrigerator as well as in this manual. Installation and service is to be performed by qualiﬁ ed personnel only! Make

sure to retain the manual for future reference.

SYMBOLS

The following symbols are used throughout the manual:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

Used without the safety alert symbol indicates, a potentially hazardous situation which, if not avoided

may result in property damage.

Information

Step-by-step instructions

CAUTION

WARNING

CAUTION

CONTENTS

- 4 -

This appliance is certiﬁ ed under the latest edition of ANSI Z21.19•CSA 1.4 Refrigerators using gas fuel. The installation

must conform with local codes, or in absence of local codes, the following standards as applicable.

In the U.S. the installation must conform with:

National Fuel Gas Code, ANSI Z223.1/NFPA 54

(latest edition).

Recreational Vehicles Code, ANSI A119.2 (latest edition).

Manufactured Home Construction and Safety Standard, Title

24 CFR, Part 3280.

If an external electrical source is utilized, the refrigerator, when

installed, must be electrically grounded in accordance with

local codes or, in the absence of local codes, the National Elec-

trical Code, ANSI/NFPA 70 - (latest edition).

•

In CANADA, the installation must conform with:

Natural Gas and Propane Installation Code, CSA B149.1

CSA Z240 RV Series, Recreational Vehicles.

Current CSA Z240.4, Gas-equipped Recreational Vehicles

and Mobile Housing.

If an external electrical source is utilized, the refrigerator,

when installed, must be electrically grounded in accordance

with local codes or, in the absence of local codes, the Canadian

Electrical Code, CSA C22.1, Parts I and II - (latest edition).

•

CERTIFICATION AND CODE REQUIREMENTS

VENTILATION REQUIREMENTS

Ventilation is one of the requirements for proper cooling

unit operation. The installation should be made in such a man-

ner as to separate the combustion system from the living space

of the mobile home or recreational vehicle. Openings for air

supply or for venting of combustion products should have a

minimum dimension of not less than 1/4 inch.

Proper installation requires one

lower fresh air intake

and one

upper exhaust vent

. Certiﬁ ed installations require one

roof

vent

and one

vent and one vent

lower side vent.

The ventilation kits shown in this

manual have been certiﬁ ed for use with RM2620 and

RM2820. The table below displays the components and their

part no.

Certiﬁ ed vent system kits

Kit no.

Components

Part no.

Roof Base

Roof Cover

Lower Side Vent

3103633.XXX*

3103634.XXX*

3109350.XXX*

* Replace “XXX” with the color code numbers. For color codes,

contact your supplier. For further information, contact your dealer or

distributor.

INSTALLATION INSTRUCTIONS

The ventilation kits must be installed and used without modi-

ﬁ cation! An opening toward the outside at ﬂ oor level in the

refrigerator compartment has be provided for ventilation of

heavier-than-air fuel gases. The lower vent of the recommended

kits is provided with proper size openings. The ﬂ ow of combus-

tion and ventilating air must not be obstructed.

The lower side vent is ﬁ tted with a panel, which provides an ad-

equate access opening for ready serviceability of the burner and

control manifold of the refrigerator. This should be centered on

the back of the refrigerator.

NOTE!

While washing the RV - do not spray any water

through the refrigerator vents.

- 5 -

INSTALLATION INSTRUCTIONS

Side view View from above

H A W

OVERALL AND RECESS DIMENSIONS

Dimensions

Model

Overall

Recess

Height A

Width B

Depth C

Height H

Width W

Depth D

RM2620

inches

51-31/32

22-23/32

24-9/16

49-17/32

21-13/16

24-3/32

1320

577

624

1258

554

612

RM2820

inches

57-7/8

24-39/64

24-9/16

55-7/16

23-11/16

24-3/32

1470

625

624

1408

601

612

VENTILATION HEIGHTS

It is essential that all maximum or minimum dimensions are

strictly maintained, as the performance of the refrigerator is de-

pendent on adequate ﬂ ow of air over the rear of the refrigerator.

Minimum ventilation heights

Installation with roof vent and lower side vent

RM2620

inches

1372

RM2820

1524

NOTE: The upper vent should be

centered over the condenser coil

at the back of the refrigerator.

Minimum

ventilation

height

Condenser

- 6 -

INSTALLATION INSTRUCTIONS

INSTALLING THE REFRIGERATOR

Make sure the ﬂ oor is solid and level.

The refrigerator must be installed in a substantial enclosure

and level.

NOTE!

Do not install the appliance directly on carpeting.

Carpeting must be removed or protected by a metal or wood

panel beneath the appliance, which extends at least full

width and depth of the appliance.

All areas within the recess have to be sealed. Verify that

there is a complete seal between the front frame of the

refrigerator and the top, sides and bottom of the enclosure.

A length of sealing strip is applied to the rear surface of the

front frame for this purpose. The sealing should provide a

provide a complete isolation of the appliance’s combustion

system from the vehicle interior.

•

NOTE!

Be careful

not to damage the

sealing strip when

the refrigerator is put

in place.

SECURING THE REFRIGERATOR

It is important to follow the sequence in securing refrigerator in

enclosure since failure in doing that can cause leakage between

the frame and cabinet!

Plastic caps are provided to cover the screw holes in the top

decoration.

Any space between the counter, storage area or ceiling and top

of the refrigerator greater den 1½ inches should be blocked.

The heat produced at the rear of the refrigerator will become

trapped in this space, making the top of the refrigerator hot and

reduce the efﬁ ciency of the refrigerator.

After the refrigerator has been installed (ensuring a combustion

seal at the front frame), the refrigerator is to be secured in the

enclosure with six screws (not included).

Install the six screws in the following order:

Two screws installed through the front base.

Two screws installed in the top frame.

Two screws installed in the rear base.

The refrigerator is provided with a lower front strip (shipped as

a loose part). The front strip is to be attached after the refrigera-

tor is set into the cutout opening.

4 th.

1 st.

2 nd.

3 rd.

K K

CLEARANCES

Minimum clearances (in inches) to combustible materials:

Top (

) 0

Side (

) 0

Bottom (

) 0

Rear (

) 0

M: The distance b

etween the rearmost part of the refrigerator and the

wall behind it.

- 7 -

INSTALLATION INSTRUCTIONS

DRAIN WATER HOSE

A hole must be drilled through ﬂ ooring and the installer needs

to make sure the hose does not kink when run through the ﬂ oor.

Seal around the hose that goes through the drilled hole. If a

longer hose than supplied is required to get the water to drain

outside of the vehicle, the installer will have to supply the extra

length of hose.

CONNECTIONS

Gas connection

Hook up to the gas supply line is accomplished at the manual

gas valve, which is furnished with a 3/8” SAE (UNF 5/8” -18)

male ﬂ are connection. All completed connections should be ex-

amined for leaks using a solution of liquid detergent and water.

Be careful when working on or near the gas system.

Do not use an open ﬂ ame to check for gas leaks!

The gas supply system must incorporate a pressure regulator

to maintain a supply pressure of not more than 11 inches water

column. When testing the gas supply system at test pressures:

> 1/2 psi

- the refrigerator and its individual shutoff valve

must be disconnected from the gas supply piping system.

≤

1/2 psi

- the appliance must be isolated from the gas

supply piping system by closing its individual manual shut-

off valve.

If detailed instructions on the installation and connection

to the gas supply are required, please contact your dealer or

distributor.

•

Testing LP gas safety shut off

NOTE!

The gas safety shut off must be tested after the refrig-

erator is connected to LP gas supply.

To test the gas safety shut off, follow these steps:

Start the refrigerator and switch to GAS mode.

Check that the gas ﬂ ame is lit and the GAS mode

indicator lamp is on.

Close the manual gas shutoff valve at the back of the

refrigerator.

Wait for one minute. The CHECK indicator lamp

should be lit and the GAS mode indicator lamp

should be off.

Remove the protection cover. Open the manual gas

shutoff valve. Do not change any button positions on

the control panel.

Apply a non corrosive commercial bubble solution

to the burner jet oriﬁ ce. No bubbles should appear at

the opening of the burner jet oriﬁ ce. The presence of

bubbles indicates a defective gas safety shutoff, and

service is required.

If no bubbles were present at the burner jet oriﬁ ce, it

should be rinsed with fresh water. Be careful not to

damage the burner jet oriﬁ ce.

Replace the cover.

Turn off the refrigerator by pressing the ON/OFF

button and then, turn it back on. Normal operation of

the burner should return. Allow the burner to operate

for a minimum of ﬁ ve minutes.

Hole for drain water hose

WARNING

- 8 -

To remove the refrigerator, follow these steps:

Cap the gas supply line.

Loosen the screws anchoring the refrigerator to the

enclosure.

Slide the refrigerator out of the compartment.

When replacing the refrigerator make sure that the sealing

strips are properly positioned. Check all connections for gas

leaks. Replacement is the reverse of removal.

Electrical connection

120 V AC connection

The refrigerator is equipped with a grounded three-prong plug

for your protection against shock hazards. It should be plugged

directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug!

The free length of the cord is 2 feet and therefore recommended

that the receptacle be located to the left side (opposite side of

refrigerator burner assembly) of the refrigerator (viewed from

the rear). The receptacle should be 3” (from the bottom of the

plastic receptacle) above the refrigerator mounting ﬂ oor. This

allows easy access through the vent door. The cord should be

routed to avoid direct contact with the burner cover, ﬂ ue cover

or any other components that could damage the cord insulation.

INSTALLATION INSTRUCTIONS

REFRIGERATOR REMOVAL

Before removing the refrigerator:

Verify that the AC and DC voltage leads are disconnected.

Shut off the gas supply.

Disconnect the gas supply line at the rear of the refrigerator.

Always use a back up wrench when loosening and tighten-

ing connections.

•

120 Volt AC

receptacle

3”

12 V DC connection

This refrigerator model is not designed for 12 V DC operation

of the cooling system; however, a continuous 12 V DC must be

supplied to the refrigerator to operate the controls.

Use a minimum of a 14 gauge wire between the battery and

refrigerator to supply the control voltage. The connection is

made to the positive (+) and negative (-) terminals located at

the rear of the refrigerator. Correct polarity must be observed

when connecting to the DC supply.

NOTE!

Do not use the chassis or vehicle frame as one of the

conductors. Connect two wires at the refrigerator and route to

the DC supply.

- 9 -

MOUNTING INSTRUCTIONS

INSTALLING THE DOOR PANELS

The refrigerator is normally delivered without door panels.

Before starting the mounting work, read this instruction thor-

oughly and check that the panel dimensions are in compliance

with those given in the “Panel dimensions” table.

Panel dimensions

max. thickness 5/32" (4 mm)

Refrigerator

model

Height

max

min

Width

max min

RM2620

upper

306

304

515

513

inch

12-3/64

11-31/32

20-9/32

20-13/64

lower

819

817

515

513

inch

32-1/4

32-5/32

20-9/32

20-13/64

RM2820

upper

378

376

563

561

inch

14-7/8

14-51/64

22-11/64

22-3/32

lower

897

895

563

561

inch

35-5/16

35-15/64

22-11/64

22-3/32

To install the door panels, follow these steps:

Open the door 90 degrees.

On new refrigerators, the decoration strips are taped

inside the door; if installed on the door, remove

the door decoration strip (2) by removing its two

screws (1).

Insert one vertical edges into the groove of the door

frame (3).

Bend the panel gently so that the free side of the

panel can be slipped into the corresponding groove

of the door frame (4).

Slide the panel down into the groove of the bottom

frame (5).

Put the decoration strip across the door so that the

gap between the upper edge of the panel and the

door frame is covered and then, push it upward (6).

The tabs on the inside of the strip should ﬁ t behind

the ﬂ ange of the door frame.

Secure the decoration strip with the two screws

removed in step 1.

- 10 -

REVERSING THE DOOR SWING

The refrigerator is equipped with hinges that makes it possible

to change the direction the door opens by moving the hinges to

the opposite side.

To change the door hinges from one side to the other, follow

these steps:

Open the top door and remove the two screws hold-

ing the top decoration. The screws are accessible

from beneath.

Remove the top hinge pin and lift out the top door.

Remove center hinge pin and lift out the lower door.

Unscrew the bottom hinge pin.

Remove the plastic cap from the opposite lower

hinge and place it in the hole just “left empty” by the

lower hinge pin.

Screw the lower hinge pin in the hole from which the

plastic cap was removed.

Before replacing the doors on the refrigerator, re-

move the catches and move them to the opposite side

of the cabinet. The holes are covered with plastic

caps that must be removed and inserted in the holes

that previously held the catches.

Unscrew the handles and move them to the opposite

side of the door.

Insert the plastic caps into the holes left open on the

doors. (Plastic caps for empty holes are in the parts

bag inside the refrigerator.)

Remount the doors and hinge pins in the reverse

order of their removal.

Before the top decoration is reﬁ tted, check that the

door closes easily and the gasket seals well on all

sides.

10.

11.

MOUNTING INSTRUCTIONS

Andere Handbücher für CLASSIC RM 2620

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic NDR1492-S Bedienungsanleitung

Dometic

Dometic DE15F Bedienungsanleitung

Dometic

Dometic RH 456LDE Bedienungsanleitung

Dometic

Dometic A30S1 Bedienungsanleitung

Dometic

Dometic miniCool Bedienungsanleitung

Dometic

Dometic RM3862 Bedienungsanleitung

Dometic

Dometic RM1350M Handbuch

Dometic

Dometic 5 Series Bedienungsanleitung

Dometic

Dometic RM2452 Handbuch

Dometic

Dometic 9600002646 Bedienungsanleitung

Dometic

Dometic DM50CD Bedienungsanleitung

Dometic

Dometic A 602K Bedienungsanleitung

Dometic

Dometic CLASSIC RH423LDBI Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic RM 2820 Bedienungsanleitung

Dometic

Dometic RMS 8400 Bedienungsanleitung

Dometic

Dometic DM50NTE UPOE Bedienungsanleitung

Dometic

Dometic miniCool Bedienungsanleitung

Dometic

Dometic EA 3280 Bedienungsanleitung

Dometic

Dometic DS 200 Bedienungsanleitung

Dometic

Dometic F400 Bedienungsanleitung

Dometic

Dometic miniCool EA 3210 Bedienungsanleitung

Dometic

Dometic RM2410 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung