Dometic RC 1180 Bedienungsanleitung

207.5196.01

Combi Box 3 Way Fridge & Freezer

RC 1180

Operating Instructions NZ

Thank you for choosing our appliance. We are sure it will provide you with trou le-free use.

In the following, we would like to familiarise you with some sym ols, which we ring to your attention to ensure

the safe and efficient operation of the appliance:

source of danger, in event of improper operation

suggested useful tips to read

information concerning environmental protection

The RC 1180 you have purchased is designed for operation on 230 Volt electrical mains, from a 12 Volt attery

or from ottled (LP) gas.

Important!

Do not operate this appliance in any unvented enclosed areas such as tents or motor

vehicles. Fresh air circulation must e availa le to the unit at all times.

Please read these operating instructions carefully before putting the

refrigeration unit into operation. If you later sell or dispose of it, please ensure

that the new owner receives these operating instructions.

CON EN

CON EN S

1. Unpacking

2. View of the appliance

3. Cleaning

4. Positioning the appliance

5. Using the appliance

5.1. From 230 Volt electrical mains

5.2. From 12 Volt vehicle attery

5.3. From LP ottled gas

6. Useful suggestions

7. Defrosting, cleaning and maintenance

8. Trou le shooting

9. Putting into operation, technical data

9.1. Connecting to 230 Volt electrical mains

9.2. Connecting to 12 Volt vehicle attery

9.3. Connecting to LP ottled gas cylinder

9.4. Connection of gas supply

10. Environmental protection information

11. Recycling

1. Unpacking

After removal from the card oard packaging, make

sure the appliance is not damaged. If you find damage

to the appliance resulting from transport, report it

immediately to the transportation firm.

2. View of the appliance

1. insulated casing

2. insulated lid

3. control panel

4. grill

5. remova le divider

Figure 1.

Figure 2.

3. Cleaning

Clean oth the inside and outside of the

appliance efore putting it into use.

To do so, use a soft towel, lukewarm water and a

non-a rasive detergent. Ensure water does not

enter the rear cover grill or the control panel.

Afterwards, wipe the appliance with a clean towel

and cleanwater, and then wipe it dry.

To avoid damage, do not use soap, soda or

a rasive cleaners.

4. Positioning the appliance

During the refrigeration process, the appliance

gives off heat from the condenser (under the

upper part of the rear cover) into the surrounding air.

The more ventilated the condenser is, the more

effective the refrigeration will e.

For maximum performance the appliance must

e level at all times when operating. If the

appliance is operating in a moving vehicle, the

amount of the refrigeration will e slightly less

than if the appliance is level in a stationary

position.This is caused y the movement of the

vehicle impairing the flow of the refrigerant within

the unit.

It is important that the appliance is not directly

exposed to radiated heat (sunlight, radiator, near

an oven, etc.).

5. Using the appliance

The ca le for 230 Volt mains connection, the 12V

connection and the gas inlet are located on the rear

cover of the RC1180 (Figure 2).

5.1. Operating from 230 Volt

electrical mains

Make sure the voltage shown on the data plate of the

appliance matches that of the mains voltage to which

you wish to connect the appliance. Pull out the mains

connecting ca le and connect it to a receptacle

earthed socket for connection.

When connecting the appliance for the first time, set

the thermostat to maximum; then, after a out five

hours, set it ack towards minimum, according to your

cooling needs.

NB: Plug is provided according to specific

regulations in each country and may be different to

that shown.

5.2. Operating from 12 Volt

vehicle battery

Make sure the voltage shown on the data plate of the

appliance matches the voltage of the vehicle attery

(12V).

In 12V operation, the appliance runs continuously

without temperature control.

The appliance is supplied with a matching pair of

12 Volt MALE + FEMALE plugs (see 9,2

connection to vehicle power source).

For 12V operation, make sure, if the engine is not

running, that the switch is turned off. Otherwise, the

appliance will discharge the vehicle attery when in

operation.

5.3. Operating from LP bottled gas

Connection to the gas cylinder is descri ed in

sections 9.3. and 9.4.

After opening the valve of the gas cylinder and

checking for gas leaks (Figure 4) turn thermostat to

maximum position, press down the gas safety valve

and at the same time, press the piezo-ignition utton

(marked with a star) several times in quick succession.

If the flame does not ignite, repeat the process. (Air in

the appliance gas line prior to connection to the gas

cylinder must e purged. Only then can the gas e lit.)

Ignition of the flame can e verified through the flame-

view opening (Figure 5). After you have the flame

alight keep the safety gas valve pressed down for a

further 10 seconds.

Figure 3.

Figure 4.

Figure 5.

6. Useful suggestions

When setting out on a trip, run the appliance on

230 V for 24 hours prior to departure. Place food

in a pre-cooled condition into the appliance.

Frost forms on the evaporator panel when in

operation. When opening the lid or putting in

food, some of this frost melts and collects in the

form of water on the ottom of the appliance.

Wipe the water off occasionally using a sponge.

Avoid putting foods with fragile packaging (such

as glass) into the refrigeration unit. Movements

and shaking of the unit may cause these items to

reak.

Once the RC 1180 is in its permanent position,

make sure foods do not come into contact with

the evaporator panel, as this can cause freezer-

urn to the foods.

The appliance is not operated on 12 Volts when

your vehicle is parked, otherwise you will drain

the attery in a short time.

Only one power source is used at a time to run

the appliance.

7. Defrosting, cleaning and

maintenance

For defrosting, always unplug the appliance from an

electrical power source to avoid the risk of shock.

Make sure no other power source is connected (gas

or 12V). Remove food from the refrigeration unit and

leave the lid open. Depending on the temperature,

frost melts in a short time from the evaporator panel,

with water collecting at the ottom of the appliance.

Wipe it off using a towel. Afterwards, clean the

appliance y following the instructions in section 3.

Leave the lid ajar to prevent any odours from forming.

The appliance is serviced depending on use, at least

once a year y an authorised service agent.

8. rouble shooting

Before calling a service technician please check

carefully the operating instructions, service ooklet

and the warranty terms and conditions:

Are location and ventilation satisfactory?

Is the appliance level?

Is there a current in the wall socket and is the

connection suita le for the appliance?

Is the mains power ca le damaged?

For mains operation, is the electric thermostat

swiched on?

For gas operation, was the safety valve kno

pressed down long enough?

Is the thermostat kno set towards the maximum

position?

Is the gas cylinder or the pressure regulator valve

open?

Is there any gas in the cylinder? (If y shaking, no

liquid movement can e detected, then the

cylinder is empty.)

Is more than one power source connected (such

as gas or electricity)?

Was warm food placed in the unit?

Was a large quantity of food put in at one time?

9. Putting into operation

You must, in all instances, operate the

appliance from a single energy source only.

Connecting several energy sources at the same time

will cause failure of the appliance.

echnical data:

9.1 Connecting to 230 Volt

electrical mains

Make sure no other energy source is connected

(gas, 12V).

The appliance may only e operated from nominal

voltage mains as shown on the data plate. The

appliance mains plug may e connected to a mains

socket earthed in accordance with regulations.

Model RC 1180

Gross volume 50 litre

Refrigerator volume 30 litre

Freezer volume 16 litre

Removable Divider volume 4 litre

Mains o eration 230V (AC)

In ut 120W (0,5 Am s)

Energy consum tion 2.1 kWh/24h

Battery o eration 12V (DC)

In ut 120W (10 Am s)

Energy consum tion 240Ah/24h

Gas ressure ( ) 2.75kPa (11 water gauge)

Gas ty e LP

Jet size 28

Gas consum tion 0,833 Mj/h

Climate class N

Refrigerant 580g NH3+ H2O

9.2 Connecting to 12 Volt vehicle

battery

Make sure no other energy source is connected (gas,

230V).

The 12V female socket is on the ackwall of the

appliance, while the male plug is an accessory

supplied with your new RC 1180.

Connect the wires from the 12 Volt attery to the male

plug (see recommended 12 Volt wiring for vehicle).

Secure earth wire firmly (Polarity is not important).

See fig. 6.

Attention: Connection to the positive pole may

only be made through a 16A fuse!

The 12V operation is cut off y disconnecting the plug.

Push the fixing ta with a screw-driver as can e seen

in fig. 7. after that the plug can e disconnected.

Recommended 12 Volt wiring for vehicle:

Two wires must e run direct to the attery one to

each terminal. These wires must e no less than 6

mm2auto ca le and kept to a practical minimum

length. A 16 Amp fuse must e fitted in the positive

lead as close as practical to the attery terminal. A 16

Amp switch may e fitted in a convenient position to

switch the current on or off to the appliance.

All electrical connections must e of good quality to

avoid voltage drop.

Note: it is NOT recommended to run this 12 Volt

appliance from a 12 Volt cigarette lighter outlet.

9.3 Connecting to LP gas cylinder

Make sure no other energy source is connected

(230V, 12V).

The unit must not e connected to town or natural gas

pipelines. It is only suita le for use with propane gas.

The RC 1180 is equipped for a specific gas-pressure,

2.75kPa (11 w. g.) . The rating-plate states the

pressure that is correct. It is important that a non-

adjusta le pressure-regulator is used to reduce the

pressure in the gas cylinder to the operating pressure

specified on the rating-plate. No other pressure may

e used.

Needle valve-operated gas control taps are NOT

suita le for use with this appliance and must not e

used as a su stitute for a pressure regulator.

Figure 6.

Figure 7.

9.4 Connection of gas supply

Always connect in the following sequence:

GAS BOTTLE →PRESSURE-REGULATOR →

→ APPLIANCE.

To connect the appliance to the pressure-regulator

SUREFLEX ARMOURED FLEXIBLE PIPE should e

used. This can e ordered through CALOR GAS

dealers, caravan accessory shops, or direct from the

manufacturer, The Lunken Co. Ltd.

When ordering the Sureflex Pipe, it must e specified

which type of connector is required at each end:

a) if the pressure-regulator outlet has a 3/8" B.S.P.

female thread, the pipe must have a 3/8" B.S.P.

male thread at one end;

) if the pressure-regulator has a ridged nozzle outlet

instead of a thread, the pipe must have a special

connector at one end.

To connect this to the pressure-regulator, first

unscrew the nut (3) and place it tgether with the sleeve

(2) onto the nozzle of the regulator. The shouldered

end of the sleeve should face away from the regulator!

Remove the ru er '0'ring (1) and push it over the end

of the nozzle so that it locates in the first corrugation.

Push the threaded end ot the Sureflex Pipe against

the end of the nozzle, then screw up the nut,

tightening the assem ly with spanners to make a gas-

tight joint.

In oth of the a ove instances, the other end of the

Sureflex Pipe should terminate in a 1/4" o.d.

extension piece. In order to connect this to a 1/8"

B.S.P. female threaded gas inlet of the appliance a

coupling which has a 1/8" B.S.P. male thread at

one end and a nut and 1/4" olive connection at the

other end to suit the 1/4" o.d. extension piece

(such as manufactured y Wade Couplings Ltd.

under their part num er 4063/1 is needed.

When fitting the connection to the gas inlet of the

appliance y applying a fork-spanner, hold

counterpart to avoid straining and possi ly

damaging.

The gas ottle (Propane) may only e used in an

upright position and particular care must e taken

every time the appliance is connected to the gas

ottle to ensure that there are no leaks, that the

tu ing (ru er hose) is not under tension or kinked,

and that it is not in contact with hot surfaces.

The tu ing and the gas ottle should always e

located in positions where they will not e tripped

over or otherwise inadvertently distur ed.

Before attempting to light the urner, every time

after connection, turn on the gas at the ottle and

check the gas connections for leaks y applying a

soap and water solution over them and watching for

u les, which would indicate a leak.

After testing dry off traces of detergent.

For your safety:

Do not check for leaks with a naked flame! Do not smoke while checking for leaks!

Inhaltsverzeichnis

Andere Dometic Kühlschrank Handbücher

Dometic

Dometic HIPRO CRUISE N30SCL Bedienungsanleitung

Dometic

Dometic RM2351 Bedienungsanleitung

Dometic

Dometic RMD 8501 Bedienungsanleitung

Dometic

Dometic HIPRO CRUISE N30GCL Bedienungsanleitung

Dometic

Dometic RM 5310 Bedienungsanleitung

Dometic

Dometic RML8230 Bedienungsanleitung

Dometic

Dometic RM 5310 Bedienungsanleitung

Dometic

Dometic miniCool DS 600 Bedienungsanleitung

Dometic

Dometic RM2662 Bedienungsanleitung

Dometic

Dometic RM2354 Bedienungsanleitung

Dometic

Dometic RM 5380 Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Dometic

Dometic 9 SERIES Bedienungsanleitung

Dometic

Dometic RC 1600 EGP Bedienungsanleitung

Dometic

Dometic A 602K Bedienungsanleitung

Dometic

Dometic RM 3962SF Bedienungsanleitung

Dometic

Dometic RMD10.5 Bedienungsanleitung

Dometic

Dometic myfridge mf5m Bedienungsanleitung

Dometic

Dometic RM 5310 Bedienungsanleitung

Dometic

Dometic CI Series Bedienungsanleitung

Dometic

Dometic miniCool EA 3210 Bedienungsanleitung

Dometic

Dometic ABSORPTION RMD 8501 Bedienungsanleitung

Dometic

Dometic RH 430LD Bedienungsanleitung

Dometic

Dometic REFRIGERATION 10-Series Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung