DoorBird A1051 Series Bedienungsanleitung

Page 2-11

Installation Manual

Internet Firewall

A1051 Series

Page 22-31

Manuel d‘installation

Pare-feu Internet

A1051 Serie

Seite 12-21

Installationsanleitung

Internet Firewall

A1051 Serie

VERSION ., MIN. HW .

A1051

Páginas 32-39

Manual de instalación

Cortafuegos de Internet

A1051 Serie

Pagina 40-51

Istruzioni per l’installazione

Internet Firewall

Serie A1051

INSTALLATION MANUAL

Read these instructions carefully before starting to use

any components. Keep the manual so you can refer

to it at a later date if required. If you hand over the

device to other persons for use, please hand over the

operating manual as well.

You can always ﬁnd the most up-to-date version of the

installation manual on www.doorbird.com/support

To make things easier we use the term “device” for the

product “Internet Firewall A1051” and “mobile device”

for a smartphone or tablet.

Liability

Every care has been taken in the preparation of this

document. Please inform Bird Home Automation

GmbH of any inaccuracies or omissions. Bird Home

Automation GmbH cannot be held responsible for any

technical or typographical errors and reserves the right

to make changes to the product and manuals without

prior notice. Bird Home Automation GmbH makes

no warranty of any kind with regard to the content

of this document, including, but not limited to, the

implied warranties of merchantability and ﬁtness for

a particular purpose. Bird Home Automation GmbH

shall neither be liable nor responsible for incidental

or consequential damages in connection with the

furnishing, performance or use of this material. This

product is only to be used for its intended purpose.

Equipment Modiﬁcations

This equipment must be installed and used in

strict accordance with the instructions given in

the user documentation. This equipment contains

no components that require service by the user.

Unauthorized equipment changes or modiﬁcations

will invalidate all applicable regulatory certiﬁcations

and approvals.

Symbols used

Danger: Indicates a hazardous situation

which, if not avoided, will result in death or

serious injury.

Warning: Indicates a hazardous situation

which, if not avoided, could result in death or

serious injury.

Caution: Indicates a hazardous situation

which, if not avoided, could result in minor or

moderate injury.

NOTICE Notice: Indicates a situation which, if not

avoided, could result in damage to property.

Important: Indicates signiﬁcant information

which is essential for the product to function

correctly.

Note: Indicates useful information which

helps in getting the most out of the product.

Hazard information

• Mounting, installation and servicing work on

electrical devices may only be performed by

a qualiﬁed eletrician. Failure to observe this

regulation could result in the risk of serious

damage to health or fatal injury due to electric

shocks.

• Devices with 110-240 V connection: The device

may only be connected to an easily accessible

power socket outlet. The mains adapter must

be pulled out if a hazard occurs.

• For power supply, only use the original plug-

in mains adapter delivered with the device,

separately available DIN rail power supplies

or a recommended PoE-Switch/PoE-Injector

as speciﬁed in this manual.

• Because of electrostatic charging, direct

contact with the circuit board can result in

destruction of the device. Direct contact with

the circuit board must therefore be avoided

at any time.

• Observe the EN 60065 resp. EN 60950 resp.

EN 62368 standard.

• Do not use the device if there are signs of

damage to the housing, control elements

or connecting sockets, for example, or if it

demonstrates a malfunction. If you have any

doubts, please have the device checked by

an authorized expert.

• Do not open the device. This voids the

warranty of the device. The device does not

contain any parts that can be maintained by

the user. In the event of an error, please have

the device checked by an authorized expert.

• For safety, approval and licensing reasons

(CE/FCC/IC etc.), unauthorized change and/or

modiﬁcation of the device is not permitted.

• The device is not a toy: do not allow babies

and children to play with it.

• To avoid the danger of suffocation, keep

any packing materials away from babies

and children. Plastic ﬁlms/bags, pieces of

polystyrene, etc. are not a toy and can be

dangerous in the hands of a child. Discard any

packing materials immediately after removing

the product. Do not reuse packing materials.

• Always lay cables in such a way that they do

not become a risk to people and domestic

animals.

• Voltage is applied to parts within the

equipment. Do not touch any parts that are

not associated with the installation, wiring, or

connection. Electric shock could result.

• On devices which are not marked as weather-

proof: Keep the device away from water or

any other liquid.

• Do not install or make any wire terminations

while power supply is plugged in. It can cause

eletric shock or damage to the device.

WARNING

ENGLISH

• Before turning on power, make sure wires are

not crossed or shorted. If not, ﬁre or eletric

shock could result.

• High voltage may be present internally. Do not

open the device. Electric shock could result.

• The device is not of explosion-proof. Do

not install or use near gases or ﬂammable

materials. Fire or explosion could result.

• Do not install two power supplies in parallel

to a single input. Fire or damage to the device

could result. Be sure to connect a single power

supply to the device.

• Do not connect any terminal on the device to

an AC power line. Fire or electric shock could

result.

• Keep AC cord from being marred or crushed.

If the AC cord is fractured, ﬁre or electric shock

could result.

• Do not plug or unplug with wet hands. Electric

shock could result.

• Do not put any metal or ﬂammable material

into the device. Fire, electric shock, or device

trouble could result.

• Existing wiring may contain high voltage AC

electricity. Damage to the device or electric

shock could result. Wiring and installation

must be done by a qualiﬁed eletrician.

•When mounting the device on a wall or

ceiling, install the device in a convenient

location, but not where it could be jarred or

bumped. Injury could result.

• On devices with ground terminals, connect to

an earth ground. Otherwise ﬁre or malfunction

could result.

• On devices with plastic or real glass, do not put

high pressure on the glass. If fractured, injury

could result.

• On devices with LCD, if LCD is punctured, do

not allow contact with the liquid crystal inside.

Injury could result. If necessary, gargle your

mouth and clean your eyes or skin with clear

water for at least 15 minutes and consult your

doctor.

• Do not put anything on the device or cover

the device with cloth, silicone, glue, coating,

separate covering etc. Fire or device issues

could result.

• Do not install the device in any of the following

locations. Fire, electric shock, or device trouble

could result.

 Places under direct sunlight or places near

heating equipment that varies in temperature.

 Places subject to dust, oil, chemicals, hydrogen

sulﬁde (hot spring).

 Places subject to moisture and humidity

extremes, such as bathrooms, cellars,

greenhouses, etc.

 Places where the temperature is very low, such

WARNING

as inside a refrigerated area or in front of an air

conditioner.

 Places subject to steam or smoke (e.g. near

heating or cooking surfaces).

 Where noise generating devices such as

dimmer switches or inverter electrical

appliances are closeby.

 Locations subject to frequent vibration or

impact.

• On devices with intercom, be sure to perform

a call test with low audio volume on both

intercom devices. A sudden call etc. may arrive

causing for example damage to your ear.

• If the device does not operate properly, unplug

the power supply.

• All devices which are not marked as weather-

proof are designed for indoor use only. Do not

use outdoor.

• On devices which are marked weather-proof:

Do not spray with high-pressure water. Device

issues could result.

• We do not assume any liability for damage to

property or personal injury caused by improper

use or the failure to observe the hazard

information. In such cases, any claim under

warranty ceases. For consequential damages,

we assume no liability!

Safety instructions

• The device shall be used in compliance with

local laws and regulations.

• Store the device in a dry and ventilated

environment.

• Avoid exposing the device to shocks or heavy

pressure.

• Do not install the device on unstable brackets,

surfaces or walls. Make sure the material is

strong enough to support the weight of the

device.

• Use only applicable tools when installing the

device. Using excessive force with tools could

cause damage to the device.

• Do not use chemicals, caustic agents, or aerosol

cleaners.

• Use a clean dry cloth for cleaning.

• Use only accessories that comply with technical

speciﬁcation of the device. These can be provided

by Bird Home Automation GmbH.

• Use only spare parts provided by or

recommended by Bird Home Automation GmbH.

• Do not attempt to repair the device by yourself.

Contact Bird Home Automation GmbH for

service matters.

• Keep the device more than 1 m (3.3‘) away from

microwave, radio, TV, wireless router and any

other wireless devices.

NOTICE

• On devices with intercom or built-in speaker

or built-in microphone or signal transmission

functions, keep the wires more than 30 cm

(12‘‘) away from AC 100-240 V wiring. AC

induced noise and/or device malfunction

could result.

• Install the device in an area that will be

accessible for future inspections, repairs and

maintenance.

• If the device is used close to a cellular phone,

the device may malfunction.

• The device can be damaged if dropped.

Handle with care.

• The device turns inoperative during power

failure.

• On devices with intercom or built-in speaker

or built-in microphone, in areas where cellular

or Radio / TV broadcasting station antennas

are closeby, the device may be affected by

radio frequency interference.

• On devices with LCD screen, it must be noted

in advance that the LCD panel, though

manufactured with very high precision

techniques, inevitably will have a very small

portion of its picture elements always lit or

not lit at all. This is not considered a device

malfunction.

• On devices with intercom, due to the

environmental sound around the device, it

may hinder smooth communication, but

this is not a malfunction.

• On devices with Username/Password, the

Username/Password to access the device is

the customer‘s responsibility. Make sure to

use a password that cannot be easily guessed

by a third party. We recommend that you

change the Password on a regular basis.

• We will, under no circumstances, be liable

for damage that occurs due to failures in

power supply, network equipment or terminal

devices; failures due to Internet providers

and cellular network providers; failures such

as disconnected lines and other losses in

communication, which makes it impossible to

provide this service as well as in any way delay

this service due to any other causes outside

of our responsibility; or if an error or missing

data occurs during transmission.

Transportation

NOTICE When transporting the device, use the original

packaging or equivalent to prevent damage

to the device.

Warranty Information

For information about the device warranty, see

www.doorbird.com/warranty

Information on disposal for users of waste

electrical & electronic equipment (private

household)

This symbol on the products and/or accompanying

documents means that used electrical and electronic

products should not be mixed with general household

waste. For proper treatment, recovery and recycling,

please take these products to designated collection

points, where they will be accepted an a free of charge

basis. Alternatively, in some countries you may be able

to return your products to your local retailer upon the

purchase of an equivalent new product. Disposing

of this product correctly will help to save valuable

resources and prevent any potential negative effects

on human health and the environment which could

otherwise arise from inappropriate waste handling.

Please contact your local authority for further details

of your nearest designated collection point. Penalties

may be applicable for incorrect disposal of this waste,

in accordance with national legislation.

Information on disposal in other countries outside

the European Union

This symbol is only valid in the European Union. If you

wish to discard this product, please contact your local

authorities or dealer and ask for the correct method

of disposal.

ENGLISH

DEVICE

1) LCD Status display

Blue backlit LCD display for status and quick

error analysis

2) PWR LED

Power and diagnostic LED to display the

current status of the device.

3) 15VDC -/+ power supply

Screw terminal plug for connecting a DoorBird

power supply (available separately) to the device as

an alternative to PoE.

4) TO/FROM INTERCOM LAN/POE IN

RJ45 jack for connecting a network cable (Cat.5 or

higher) with the network segment that is attached

to the DoorBird IP devices. Use this port to power

the device with PoE as an alternative to the

power supply.

5) DIN Rail connector

Connection for DIN rail clip for DIN rail mounting

6) TO/FROM ROUTER LAN

RJ45 jack for connecting a network cable (Cat.5

or better) with the network segment that is

attached to the switch/router that provides an

active internet connection.

7) SET setup button

Button to set the device into different

conﬁguration modes, e.g. to reset the device to

factory defaults.

8) Wall mounting brackets

Holder for wall mounting. Screws and dowels

included.

Front

1x Screw connection

terminal plug and

screw driver

1x Quickstart guide

with Digital Passport

1x Installation manual1x A1051 Internet Firewall

COMPONENTS*

2x Phillips countersunk head

screws and dowels

Back

VIDEOS

Need help with the installation? Be sure to watch our

installation videos which can be found on

http://www.doorbird.com/support

INSTALLATION

All the steps below should be carried out carefully

by a competent adult, taking into consideration

any applicable safety regulations. Please contact us

directly or seek the advice of a competent specialist.

Please ensure that all wires used for the

installation are undamaged along their entire

length and approved for this type of use.

SWITCHING OFF POWER

Switch off the power to all wires leading to

the assembly location, i.e. the door chime,

electric door opener, power supply unit for

the video door station etc.

MOUNTING THE DEVICE

The device can be mounted on the wall using the wall mount bracket, screws and dowels supplied with it or on

DIN-Rail using the DIN-Rail adapter supplied with it.

Network speed and network components

Please ensure that the upload speed of your Internet

connection is at least 0.5 Mbps. The user experience is

only as good as your network speed, network stability

and quality of your network components, such as

your Internet Router and WiFi access points or WiFi

repeaters. Please also make sure that your network

components are no older than two years old, have

been manufactured by a well-known manufacturer,

and have the latest ﬁrmware installed.

Should these requirements not be fulﬁlled, it may

occur, for example that the performance of audio and

video is poor or push notiﬁcations are delayed or do

not arrive on your smartphone or tablet at all.

Requirements:

High-speed Internet (via landline): DSL, cable or optical

ﬁbre

Network: Ethernet with DHCP

DETERMINING THE ASSEMBLY

LOCATION

The device is IP30 certified (not water-proof).

Please make sure to put the device into an

appropriate housing if you want to use it

outdoors.

The network cable between the device and the

PoE-Switch/PoE-Injector/ Internet Router can have a

maximum length of 80 meters/262 feet.

Option 1

WALL MOUNTING

Ensure to hit no objects (e.g. cables) when drilling the holes.

If the wall of the house is not made of wood, you

should drill dowel holes 5 mm in diameter in the

wall and then place the dowels provided into the

boreholes. If the wall of the house is made of wood,

you will usually not require any dowels. There are

special dowels for assembling the device on an

insulating wall, e.g. Fischer insulating dowels. Please

check with your insulating material manufacturer

regarding which dowels they recommend.

ENGLISH

Option 2

DIN-RAIL MOUNTING

The device can be mounted on DIN-Rail. Use the DIN rail adapter on the back of the unit.

 POWER SUPPLY

The device can be powered using PoE (Power over Ethernet) or separately available DoorBird power supplies

(Wall-Plug power supply unit or DIN rail power supply). The device does not use battery power.

Disconnect all other DoorBird devices in the network from the power supply, before commissioning the

DoorBird Internet Firewall A1051.

Option 1

POWER SUPPLY AND NETWORK

CONNECTION USING POE (POWER

OVER ETHERNET RECOMMENDED)

To power the device via a PoE-Switch (e.g. D-Link

DGS-1008P) or PoE-Injector (e.g. DoorBird Gigabit PoE

Injector A1093) in accordance with the PoE standard

IEEE 802.3af Mode A, the four wires bearing the

numbers 1, 2, 3 and 6 of a Cat.5 cable or better are

to be used. Make sure to use a high-quality Cat.5

network cable or better and with proper shielding

(Screened Foiled Twisted Pair (S/FTP or SFTP))

whereby the shield is connected to the outer metal

shield of the RJ45 plug (8P8C). If you use PoE as

a source of power, the four wires for PoE then

simultaneously form the data link.

The device won’t start if your PoE-Switch/PoE-Injector

does not support the PoE Standard IEEE 802.3af

Mode A (see PWR LED).

1. Disconnect the PoE-Switch or PoE-Injector

from the power grid.

2. Run the network cable to the installation

location of the device.

Further information on PoE can be found here:

http://www.doorbird.com/poe

Option 2

POWER SUPPLY USING A POWER

SUPPLY UNIT (AVAILABLE IN THE

DOORBIRD SHOP)

To power the device using a mains adapter, 2 insulated

wires are required. The network connection is then

established via a network cable. Power supplies are

available in our web shop:

https://www.doorbird.com/shop/

NOTICE Do not plug the power supply unit into the

wall socket yet. Only use the power supply

unit provided along with the device, or a

DIN-rail power supply unit that you can

obtain from us separately, since this has

been specially stabilized electrically and is

equipped with an integrated audio

interference reduction device. Other power

supply units may destroy the device or cause

poor transmission quality.

Option 3

POWER SUPPLY USING A DIN RAIL

POWER SUPPLY UNIT

We offer DIN rail power supplies in our web shop,

which can be installed by a specialist. The network

connection is then made via a network cable.

PORT DESCRIPTION

TO/FROM

ROUTER LAN

RJ45 jack for connecting a network cable (Cat.5 or higher) with the network segment that

is attached to the switch/router that provides an active Internet connection.

TO/FROM

INTERCOM LAN/

POE IN

RJ45 jack for connecting a network cable (Cat.5 or higher) with the network segment that

is attached to the DoorBird IP devices. Use this port to power the device with PoE.

15 VDC -

15 VDC Power supply input, negative pole (-). Please connect the black wire of the power

supply unit (mains adapter) here, if you do not power the device using PoE.

NOTICE Do not power the device simultaneously via the power supply from the power

supply unit (mains adapter) and the power supply via PoE.

15 VDC +

15 V DC Power supply input, positive pole (+). Please connect the red wire of the power

supply unit (mains adapter) here, if you do not power the device using PoE.

NOTICE Do not power the device simultaneously via the power supply from the power

supply unit (mains adapter) and the power supply via PoE.

TO/FROM INTERCOM

LAN/POE IN

PWR

15 VDC

- +

TO/FROM ROUTER

LAN

 CONNECTING THE DEVICE

It is possible to connect the cables and wires to the device conveniently and safely via the labeled screw

connection terminal. You can connect all necessary cables and wires to the device now.

NOTICE Please remove any cables and wires from the connection ports of the device that you do not need.

Use DoorBird power supply unit as an alternative to PoE.

Available in our web shop (GTIN/EAN: 4260423867314, P/N: 423867314)

ww w PoE

ENGLISH

ACTIVATE THE DEVICE

Disconnect all other DoorBird devices in the network from the power supply, before switching on the

power for the DoorBird Internet Firewall A1051.

Switch on the power leading to the assembly location. If the PWR LED does not light up, please check the

power supply. When using a wall-plug power supply and not PoE, please check whether you have connected

the positive pole and negative pole to the device correctly.

As soon as the A1051 Internet Firewall is fully operational, the DoorBird components that are connected to the

“TO/FROM INTERCOM LAN/PoE IN” RJ45 jack can be powered on. If they have been already powered up before

the device was fully operational, please reboot them.

NOTICE Do not power the device simultaneously via the power supply from the power supply unit (mains

adapter) and the power supply via PoE.

PWR LED

You can see if the device receives power by checking the PWR LED. The PWR LED lights up about 30 to 60

seconds after the device get connected to power and stays on for 5 minutes. For the connection status of the

device, please check the status display on the top. If the PWR LED does not light up, please check the power

supply. In case of PoE, make sure to use a compatible PoE device (https://www.doorbird.com/poe). When

using a wall-plug power supply and not PoE, please check whether you have connected the positive pole and

negative pole to the device correctly.

OPERATION

The A1051 Internet Firewall will block all trac that is not vital for the operation of the DoorBird System by

default. However, in some use cases it might be required to allow DoorBird components or other devices (e.g.

other smart home products) on the “TO/FROM INTERCOM LAN/PoE IN” side of the device to connect to speciﬁc

destinations. For that purpose, it is possible to whitelist certain IPs or hosts. Please refer to the App manual

https://manual.doorbird.com/app for further information.

ww w

Home/Building Network

Router PoE

Switch

Intercom Network

To also allow a local connection to a client that is not part of the ﬁrewall network (e.g. mobile device with DoorBird

App), the „Forward connected devices“ function can be activated in the Administration section of the App.

A1121 A1101

A1081

DoorBird

Door Station

TECHNICAL SPECIFICATIONS

Dimensions 104 x 75 mm x 34 mm (H x W x D)

4.10 x 2.96 x 1.32 in (H x W x D)

Power Supply

15 V DC or Power over Ethernet

(PoE IEEE 802.3 af or higher)

PoE Switch, PoE Injector or power

supply unit not included

Power

consumption 1 W

Operating

conditions

0 to +55°C / 32 to 131°F

Relative Humidity 0 % to 85 %

(non condensing)

Protection class IP 30

Mounting • Top-hat rail / DIN rail

• Wall mounting

Approvals CE, FCC, IC, RoHS, WEEE, UKCA

Connectors &

Interface

2x RJ45 socket (10/100 Base-T)

• TO/FROM ROUTER LAN

• TO/FROM INTERCOM LAN/PoE IN

1x Screw terminal

• 15 V DC Input (-/+)

Display

LCD Status Display

• Backlight (blue)

• Network status display

PWR LED

Features

Network ﬁlter:

Actively ﬁlters network trac and

blocks unauthorized access

DHCP server:

Integrated DHCP server

(10.223.x.x), up to 1,000 devices

IP whitelist:

Approval of IP addresses or

domains, such as for control

functions of smart home systems

STATUS DISPLAY

You can see if the device receives power by checking

the Status LED on the side of the device.

TO/FROM ROUTER LAN connected

Internet connection available

TO/FROM ROUTER LAN connected

No Internet connection available

TO/FROM ROUTER LAN not connected

E.g.: no network cable connected

System

requirements

Mobile end device: latest iOS

on iPhone/iPad, latest Android on

smartphone/tablet

Internet: High-speed landline

broadband Internet connection,

DSL, cable or ﬁber, no socks or

proxy server

Network: Ethernet Network, with

DHCP

Compatible with all DoorBird IP

Video Door Stations and DoorBird

Peripheral devices

Scope of

delivery

1 x A1051 Internet Firewall

1 x Installation manual

1 x Quickstart guide with Digital

Passport

1 x Small parts

Weight 155 g

EAN 4260423872103

Recommended

accessories

Power supply unit

(GTIN/EAN: 4260423867314, P/N:

423867314)

Inhaltsverzeichnis

Sprachen:

Andere DoorBird Netzwerk-Hardware Handbücher

DoorBird

DoorBird D21 Series Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung