Dorma D860 Bedienungsanleitung

5/16"



Mark

door

1 Place template on door and mark center for 2 1/8” hole at

desired backset.

2 Template should be placed on high edge of beveled door edge.



Bore two holes

1 Bore a 2 1/8” diameter hole. To avoid splintering a wood door,

bore the hole from both sides of door.

Note

If there is an existing 1 1/2” diameter cross bore, there is no

need to re-

drill cross bore

1” diameter edge hole must be

drilled 4” deep to accommodate deadbolt.

2 Drill a 1” diameter hole from the edge of door that intersects the

2 1/8” hole.

3 Using the deadbolt faceplate as a guide, mortise the edge of

door to recess the faceplate.



Prepare door jamb

1 Locate exact center of bolt and mark center lines on jamb as

shown.

2 Mark drill points 5/16” above and below horizontal center line.

3 Bore two overlapping 7/8” holes, 1 1/8” deep.

4 Clean out holes for strike box and place strike box in hole.

5 Place strike over box and trace for cutout.

6 Chisel about 1/4” deep for flush fit of strike box, strike reinforcer

and strike.



Install strike plate

1 Place strike reinforcer with screw holes toward doorstop.

2 Mark and drill two 3/16” holes for 3” wood screws.

3 Install strike reinforcer, strike box, and finish strike in the order

shown.



Install deadbolt assembly

1 Insert the deadbolt with slotted driver bar hole at the bottom of the

assembly.

2 Secure the deadbolt to the door with screws.

High side of door bevel

INSTALLATION INSTRUCTIONS

D860,

861,

862

863

880

Strike Box

Strike Reinforcer (Wood Frames)

3" Wood Screws

Strike Plate

Screws

Trim Ring

Mounting Screws

Thumbturn Assembly

Security

hield

Security Insert

Cylinder Collar

Standard Cylinder Assembly

I/C Cylinder Housing

1" diameter hole

2 1/8" diameter hole

Strike box

Strike reinforcer

3" wood screws

Strike plate

Edge of door

Deadbolt

Slotted driver bar hole

Height line

Center punch

Clear out

Deadbolt

Jamb



Install cylinder(s)

For single cylinder deadbolts:

1 Extend the bolt with a screwdriver.

2 Place security shield

in hole. NoteDo not use security shield in

existing 1 1/2” hole installation.

3 Install the cylinder and trim assembly with the driver bar in the

vertical position.

For double cylinder deadbolts:

1 Extend the bolt with a screw driver.

2 Install each cylinder with its ring and rose.

Place security shield in hole.

Note

Do not use security shield in existing 1 1/2” hole installation.

3 Insert long mounting screws and tighten.

4 Check to make sure the deadbolt operates properly.

5 Insert the faceplate.

Note 1Mount cylinders on the doors so that the mounting screws

enter from the inside of the door.

2Both driver bars must fit through the driver bar hole in the

deadbolt assembly.

Caution : Double cylinder locks are operated by key only and may

hinder emergency exit . Check for applicable fire codes and / or life

safety codes before installing double cylinder deadbolt .

www.dorma-usa.com 1-800-523-8483



Attach inside trim

1 With the driver bar in the vertical position, slide the thumbturn

assembly over the driver bar.

2 Rotate the thumbturn assembly retracts deadbolt.

3 Secure the thumbturn assembly and the cylinder to the door with

the mounting screws supplied.

4 Test lock with key and thumbturn. Bolt must travel and project fully

into strike preparation without binding.



Install core(s)

1 Put the control key into the core and turn the key 15 degrees

clockwise.

2 Adjust the throw pins if needed, then put the core into the cylinder

housing with the control key.

3 Turn the key 15 degrees counterclockwise and remove the key.

Patents :

Products are protected by one or more of the following

U.S. patents: 5713231. Other patents pending.

WD-OD002(127)

P/N 50300078

76010391

Trim ring (I.C.Core only)

Security shield

Driver bar

Cylinder and trim assembly

Extend bolt with screw driver here

Long mounting screws

Faceplate

Both driver bars fit through

slotted driver bar hole

Driver bar

Thumbturn assembly

Mounting screw

Throw pins

Core

Rotate 15 degrees

Control key

Cylinder housing

Dieses Handbuch passt für folgende Modelle

Andere Dorma Türschloss Handbücher

Dorma

Dorma MATRIX AIR Bedienungsanleitung

Dorma

Dorma PHA Glas Kit Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM PT 60 Benutzerhandbuch

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma SVP 22 DCW Series Bedienungsanleitung

Dorma

Dorma HZ 43-F Series Bedienungsanleitung

Dorma

Dorma STE 400 Bedienungsanleitung

Dorma

Dorma ARCOS UNIVERSAL PT 30 Bedienungsanleitung

Dorma

Dorma ES62 Bedienungsanleitung

Dorma

Dorma TENSOR Bedienungsanleitung

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma MATRIX AIR Standard Bedienungsanleitung

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM US 10 Benutzerhandbuch

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma C301 Bedienungsanleitung

Dorma

Dorma RTS Series Bedienungsanleitung

Dorma

Dorma Duo HOME Bedienungsanleitung

Dorma

Dorma ARCOS Universal PT 10 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

Dorma

Dorma MUNDUS PREMIUM PT 70 Benutzerhandbuch

Dorma

Dorma SVP 7000 Air Installations- und Betriebshandbuch

Dorma

Dorma ARCOS Universal PT 40 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung