Dover TWG Greer MICROGUARD 510 Bedienungsanleitung
GREER COMPANY
Crane Systems 1 of 35
MICROGUARD®510
TELESCOPIC BOOM CRANES
ORs Full 9. 7Kl b Ct wt
ERECTED 60' TELEJI B 17 AUXHD ON
PICK FROMMAINBOOM FRONT WINCH
TEST
MAX
SET
360
o
6
23,500
i2,300
44.8
62.7
26.4
o
OPERATOR'S MANUAL
GREER COMPANY
Crane Systems 2 of 35
TABLE OF CONTENTS
MicroGuard®510 Operator’s Manual
Introduction
Outline of Operation.....................................................................................................................4
What Does It Tell You?
The Pictograph.............................................................................................................................5
Information Screen.......................................................................................................................6
Parts-of-Line Indicator..................................................................................................................6
Operator Alarms Indicator............................................................................................................6
Pre-Alarm Indicator......................................................................................................................6
Overload Indicator........................................................................................................................6
Anti Two-Block Indicator ..............................................................................................................6
Bar Graph for Percentage of Rated Load....................................................................................7
Actual Load..................................................................................................................................7
Rated Capacity.............................................................................................................................7
Radius, Length, Angle..................................................................................................................7
What Must You Tell It?
Parts-of-Line.................................................................................................................................8
Point of Lift...................................................................................................................................8
Auxiliary Head On or Off..............................................................................................................8
Stowed and/or Erected Attachments ...........................................................................................8
Manual Section or Boom Mode....................................................................................................8
Jib Stowed on Boom....................................................................................................................8
Winch ...........................................................................................................................................8
Counterweight..............................................................................................................................8
Tires .............................................................................................................................................8
Outriggers ....................................................................................................................................8
Power Up Self-Test .................................................................................................................................9
Start-Up Screen.....................................................................................................................................10
Brightness and Contrast Controls ......................................................................................................11
GREER COMPANY
Crane Systems 3 of 35
TABLE OF CONTENTS continued
MicroGuard®510 Operator’s Manual
System Setup
Counterweight............................................................................................................................12
Outriggers ..................................................................................................................................13
Tires/Rigging Travel Mode.........................................................................................................14
Stowed Jibs................................................................................................................................15
Erected Jibs ...............................................................................................................................16
Auxiliary Head............................................................................................................................17
Choosing the Winch...................................................................................................................18
Choosing the Point of Lift...........................................................................................................19
Setting the Parts-of-Line ............................................................................................................20
Notes..........................................................................................................................................21
Cancel Alarm
Push Button to Cancel Audible Alarm........................................................................................22
Reset Function Kick-Out............................................................................................................23
Operator Settable Alarms
Accessing the Operator Alarms .................................................................................................24
Setting Minimum and/or Maximum Boom Angle........................................................................25
Setting Maximum Length, Maximum Height..............................................................................26
Accessing Swing and Work Area Alarms...................................................................................27
Swing Alarms.............................................................................................................................28
Setting the Left and Right Swing Alarms ...................................................................................29
Work Area Selection Mode ...................................................................................................30-31
Glossary............................................................................................................................................32-35
GREER COMPANY
Crane Systems 4 of 35
OUTLINE OF OPERATION
EXTENSION SENSORSYSTEM COMPONENTS
•MicroGuard®Display Unit The extension sensor provides an increasing voltage
proportional to the extension of the boom. A cable
attached to the boom head provides a low current
electrical path for the A2B signal
•MicroGuard® Computer Unit
•Pressure Transducers
•Extension Reel with length and angle sensors PRESSURE TRANSDUCERS
•Anti 2-Block (ATB) switches
•Cables Two pressure transducers measure the pressure in
the boom hoist cylinder. The resultant Total Moment
signal is processed to provide a continuous display of
the load suspended below the point of lift.
•Installation/Operator Manuals
The MicroGuard®510System is intended to aid the
crane operator by continuously monitoring the load
and warning of an approach to an overload or Two-
Block condition. Crane functions are monitored by
means of high accuracy sensors. The system
continuously compares the load suspended below the
boom head with the crane capacity chart stored in the
computer memory. At approach to overload, the
system warns by means of audible and visual alarms.
The system can be configured to cause function kick-
out by sending a signal to function disconnect
solenoids.
ANTI TWO BLOCK (A2B)
A switch monitors the approach of the hookblock or
overhaul ball to the boom head. The switch is held in
the normal position until the hookblock or overhaul
ball raises a weight that is mounted around the hoist
rope. When the weight is raised, it causes the switch
to operate. The resultant signal is sent to the
computer via the extension reel causing the A2B
alarm to operate and function kick-out to occur.
FUNCTION KICK-OUT
DISPLAY Electrically operated solenoids disconnect the control
lever functions for boom hoist lower, telescope out,
and winch up whenever an overload or an A2B
condition occurs.
The operator is provided with a continuous display of:
•Rated Load
•Actual Load
•Bar Graph showing Percentage of Rated Load OPERATOR SETTABLE ALARMS
•Radius of the Load These alarms, when properly set by the operator,
define the operating range. This is achieved by
means of minimum and maximum angle, maximum
height, and/or maximum length. These alarms can be
programmed for each job site and allow the operator
to work in a defined area.
•Boom Angle
•Main Boom Length
•Working Area
•Crane Configuration
On-screen messages provide the operator with visual
warnings of conditions that occur during operation of
the system.
AREA ALARM
When set, this alarm permits the operator to define
the operating zone by only two set points. The use
of this method results in a greatly enhanced working
area, and also clearly defines the operating zone.
BOOM ANGLE SENSOR
Boom angle is measured by means of a high-
accuracy potentiometer/pendulum assembly that is
damped to prevent overswing. It provides a voltage
proportional to boom angle. The boom angle sensor is
mounted inside the cable extension reel assembly.
GREER COMPANY
Crane Systems 5 of 35
THE PICTOGRAPH
MANUAL SECTION
/ BOOM MODE
JIBS
AUX HEAD
POINT OF LIFT
OUTRIGGERS
TIRES
COUNTERWEIGHT
WINCH
STOWED JIB
WINCH - contains 2 LEDs. These indicate the
selection of FRONT or REAR winch.
The PICTOGRAPH above gives a pictorial
representation of the current setup of the
system. It does this by means of light emitting
diodes (LEDs). Each shaded area contains a
group of one or more LEDs and a push button
that is pressed to change the setup selection.
STOWED JIB - contains 1 LED. This will be
illuminated when the jib is stowed on the boom.
MANUAL SECTION - contains 1 LED. It is
active on cranes that have pinned extensions or
active tip boom options.
The groups are shown below. In groups with
more than one choice or option, LEDs illuminate,
one at a time, to indicate the selection. JIBS - contain 6 LEDs. These indicate the
length and offset of the jib in use.
OUTRIGGERS -contain 3 LEDs. These indicate
the selection of either full outriggers,
intermediate, or retracted outriggers. AUX HEAD - contains 1 LED that illuminates
when the AUX HEAD is fitted.
POINT OF LIFT - contains 3 LEDs. One will
illuminate to show the point of lift.
TIRES - contain 1 LED. When operation on tires
is selected, the outrigger LED will turn off and
the tire LED will illuminate.
COUNTERWEIGHT - contains 1 LED. It is only
active on cranes that have counterweight
options.
GREER COMPANY
Crane Systems 6 of 35
WHAT DOES IT TELL YOU?
TEST
MAX
SET
6
23,500
i2,300
44.8
62.7
26.4
5
4 6
213
ORs Full 9. 7Kl b Ct wt
ERECTED 60' TELEJI B 17 AUXHD ON
PICKFROMMAINBOOM FRONT WI NCH
360
oo
1The INFORMATION SCREEN contains
details of the currently selected
configuration.
4The PRE-ALARM (AMBER) indicator
illuminates at a preset value of 90% of
Rated Capacity and provides a visual
indication of approach to overload.
2 PARTS-OF-LINE displays the parts of line
currently selected. 5The OVERLOAD INDICATOR (RED)
illuminates at a preset value of 100% of
Rated Capacity and provides a visual
indication of Maximum Allowed Load.
3 The OPERATOR ALARM lamp
illuminates when operator alarms have
been set 6The ANTI TWO-BLOCK lamp illuminates
when the A2B limit switch detects
approach to a Two-Block condition.
GREER COMPANY
Crane Systems 7 of 35
WHAT DOES IT TELL YOU?
TEST
MAX
SET
6
23,500
i2,300
44.8
62.7
26.4
9
711
10
8
12
ORs Full 9. 7Kl b Ct wt
ERECTED60' TELEJIB 17 AUXHDON
PICK FROMMAINBOOM FRONT WI NCH
360
oo
7The BAR GRAPH indicates the ACTUAL
LOAD as a PERCENTAGE OF RATED
CAPACITY.
11 The LENGTH display shows the length of
the main boom from the boom foot pin to
the sheave pin of the main boom head
machinery.
8The ACTUAL LOAD display shows total
load, including load, slings, etc.
suspended below the lifting point. 12 The ANGLE display indicates, in degrees,
the angle of the main boom relative to
horizontal.
9The RATED CAPACITY display shows
the RATED CAPACITY of the crane in the
current configuration.
10 The RADIUS display shows radius of the
load. Radius is the horizontal distance
from the centerline of rotation to the
centerline of the lifting point.
GREER COMPANY
Crane Systems 8 of 35
WHAT MUST YOU TELL IT?
TEST
MAX
SET
6
23,500
i2,300
44.8
62.7
26.4
15
13 16
14 22
19
18
17
20
21
ORs Full 9. 7Kl b Ct wt
ERECTED60' TELEJIB17 AUXHDON
PICKFROMMAINBOOM FRONT WINCH
360
oo
18 JIB STOWED ON BOOM.
13 The number of PARTS-OF-LINE. 19 Indicates which WINCH will be used
for the pick.
14 POINT OF LIFT, e.g. main boom,
auxiliary head or jib. 20 Indicates which COUNTERWEIGHT
is fitted (if applicable).
15 AUXILIARY HEAD ON or OFF the
crane. 21 TIRES creep, static, 2 1/2 MPH,
and RIGGING/TRAVEL mode.
16 Indicates JIB configuration in use.
17 MANUAL SECTION or ACTIVE TIP
extended (if applicable). 22 OUTRIGGERS full extension, mid
extension, or retracted.
GREER COMPANY
Crane Systems 9 of 35
POWER UP SELF-TEST
TEST
MAX
SET
I8
888;800 I88.8
26
SYSTEMSELF TEST I N PROGRESS
TEREXCD225
CHART 12262- 1205/ 20W
888;800
I88.8
I88.8
Immediately following electrical power up or
following operation of the TEST SWITCH
(ITEM 26), the system executes a self-test that
lasts for 8 seconds.
During this time, the numerical display segments
and bar graph segments are all turned on, the
audible alarm will sound, and alarm indicator
lights are illuminated.
The information display shows the crane model
and rating chart number.
GREER COMPANY
Crane Systems 10 of 35
START-UP SCREEN
TEST
MAX
SET
--- -
--- -
-- -
27
CI MA MANUAL, ASME/ ANSI B30. 5
OSHA REGS AND OPERATORS MANUAL
READ/ UNDERSTAND THE FOLLOWING...
PRESS TOCONTINUE>
-- -
-- -
-
Operation of the BOTTOM RIGHT
INFORMATION DISPLAY PUSH BUTTON
(ITEM 27) will acknowledge the information
display message and allow the system to start
normal operation.
Immediately following power up self-test, the
display indications will show as above. During
this time, crane motions are disabled by the
system function kickout.
Inhaltsverzeichnis
Andere Dover Touchscreen Handbücher
Beliebte Touchscreen Handbücher anderer Marken
IBASE Technology
IBASE Technology ASTUT-152-RE1S Bedienungsanleitung
YASKAWA
YASKAWA TP 610C Bedienungsanleitung
B&R
B&R Power Panel C Series Bedienungsanleitung
Beijer Electronics
Beijer Electronics X2 control Bedienungsanleitung
AXIOMTEK
AXIOMTEK GOT321W-521 Bedienungsanleitung
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Bedienungsanleitung
