Drieaz Dri-Pod F451 Bedienungsanleitung

07-01759B 2012-04 Warranty 07-01760 1 Dri-Eaz Products, Inc.
Owner’s Manual
Dri-Pod™ Direct Flow Carpet Dryer
Patent Pending
The Dri-Pod is a high velocity airmover that creates an aggressive 360°airflow
across floor surfaces to accelerate drying.
READ AND SAVE THESE INSTRUCTIONS
Read and understand this manual before operating.
WARNING! To reduce the risk of fire or electric shock, do not
use this fan with any solid-state speed control device.
WARNING! Unit must be grounded. Do not use with an
extension cord. Connect only to an outlet provided with a ground
fault interrupting device.
WARNING! Never operate a unit with a damaged power cord, as
this may lead to electrical or fire hazards. If power cord is
damaged, it must be replaced by a cord of the same type and
amperage rating.
WARNING! Do not touch grills when unit is operating.
NOTICE: Keep motor dry. For indoor use only.
NOTICE: Unplug when not in use or when moving unit.
NOTICE: Do not allow children to play with or around the unit.
Be sure the unit is inaccessible to children when not attended.
NOTICE: Always operate the unit on a stable, level surface so it
cannot fall and cause injury.
OPERATING INSTRUCTIONS
1. Unwrap the cord and plug the unit into a standard 115V
outlet. CAUTION: Be sure switch is in the off position before
connecting unit to power outlet.
2. Position the Dri-Pod in the center of an area to be dried.
Switch on. The Dri-Pod can dry an area approximately
10 × 10 ft. (3 × 3 m).
3. When surface is dry to the touch, switch unit off and
reposition the unit in the next section to be dried.
4. When finished, unplug the unit and re-wrap the cord in the
cord wrap.
Transporting and Storing
1. Always use the handle to load or carry the unit. Units may
be stacked for transport and storage.
2. When transporting in a vehicle, secure the unit carefully to
prevent sliding and damage to the unit and/or injury to
vehicle occupants.
PARTS IDENTIFICATION
FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or the Dri-Eaz
Service Department at 800-932-3030
DRI-EAZ PRODUCTS, INC.
15180 Josh Wilson Road, Burlington, WA USA 98233
Fax: 360-757-7950 Phone: 360-757-7776
www.dri-eaz.com
SPECIFICATIONS
Model F451
Weight 10.6 lbs. | 4.8 kg
Dimensions
(D × W × H)
15.2 × 15.2 × 8.9 in.
38.5 × 38.5 × 22.5 cm
Amp draw 1.1 amps
Control On/off switch
Power 235W/115V
Cord length 10 ft. | 3 m
Fan 5 blades
Construction Injection molded housing, wire grill
Safety ETL approved to UL and CSA standards
Specifications are subject to change without notice. Some values
may be approximate.
Handle
On/off switch
Cord wrap

07-01759B 2012-04 Warranty 07-01760 2 Dri-Eaz Products, Inc.
Manual para el usuario
Secador de alfombras de flujo directo Dri-Pod™
Patente en trámite
El Dri-Pod es un removedor de aire de alta velocidad que genera un flujo de aire dinámico
de 360° a través de las superficies del piso para acelerar el proceso de secado.
LEA Y GUARDE ESTAS INSTRUCCIONES
Lea y comprenda este manual antes de
utilizar el equipo.
¡ADVERTENCIA! Para reducir el riesgo de incendio o descarga
eléctrica, no utilice este ventilador con ningún dispositivo de
control de velocidad de estado sólido.
¡ADVERTENCIA! La unidad debe tener descarga a tierra. No
use cables prolongadores. Conecte el equipo únicamente a un
tomacorriente que tenga un dispositivo de interrupción de fuga a
tierra.
¡ADVERTENCIA! Nunca utilice una unidad con el cable de
alimentación dañado, ya que puede provocar riesgos eléctricos
o incendios. Si el cable de alimentación está dañado, debe
reemplazarse con un cable del mismo tipo y amperaje.
¡ADVERTENCIA! No toque las rejillas cuando la unidad está en
funcionamiento.
AVISO: Mantenga seco el motor. Solo para uso interior.
AVISO: Desenchufe el equipo cuando no lo use o para
transportarlo.
AVISO: No permita que los niños jueguen con la unidad o cerca
de ella. La unidad deberá estar fuera del alcance de los niños
cuando usted no esté presente.
AVISO: Siempre utilice la unidad sobre una superficie estable y
plana para evitar que se caiga y cause algún daño.
INSTRUCCIONES DE USO
1. Desenrolle el cable y enchufe la unidad en un tomacorriente
estándar de 115 voltios. PRECAUCIÓN: Asegúrese de que
el interruptor esté en la posición de apagado antes de
conectar la unidad al tomacorriente.
2. Coloque el Dri-Pod en el centro del área que quiera secar.
Enciéndalo. El Dri-Pod puede secar un área de
aproximadamente 10 pies (3 metros) de diámetro.
3. Cuando la superficie esté seca al tacto, apague la unidad y
ubíquela en la siguiente sección que quiera secar.
4. Cuando termine, desenchufe la unidad y vuelva a enrollar el
cable en el enrollador.
Transporte y almacenamiento
1. Siempre utilice la manija para cargar o trasladar la unidad.
Las unidades se pueden apilar para su transporte y
almacenamiento.
2. Cuando transporte la unidad en un vehículo, sujétela bien
para evitar que se deslice y se dañe, o que lastime a los
ocupantes del vehículo.
IDENTIFICACIÓN DE LAS PIEZAS
Para solicitar servicio técnico, llame al distribuidor de su zona o al
Departamento de Servicio Técnico de Dri-Eaz, al 800-932-3030.
15180 Josh Wilson Road
Burlington, WA USA 98233
Fax: 360-757-7950 Teléfono: 360-757-7776 www.dri-eaz.com
ESPECIFICACIONES
Modelo F451
Peso 10.6 lb | 4.8 kg
Dimensiones
(Profundidad ×
Ancho × Altura)
15.2 × 15.2 × 8.9 in
38.5 × 38.5 × 22.5 cm
Amperaje 1.1 A
Control Interruptor de encendido y apagado
Potencia 235 W/115 V
Longitud del cable 10 ft | 3 m
Ventilador 5 aspas
Construcción Carcasa moldeada por inyección; parrilla de
alambre
Seguridad Aprobación de ETL conforme a las normas UL
y CSA
Las especificaciones están sujetas a cambios sin previo aviso.
Algunos valores pueden ser aproximados.
Manija
Enrollador
de cable
Interruptor de
encendido y
apagado