Drive 15230 Bedienungsanleitung

Model # 15230 & 15235

user manual

READ THESE INSTRUCTIONS BEFORE

OPERATING THE DRIVE HOMECARE LOW BED

SAVE THESE INSTRUCTIONS FOR FUTURE USE

homecare bed

FULL ELECTRIC AND SEMI-ELECRTIC LOW BED

www.drivemedical.com

WARNING: KEEP HANDS AND FEET CLEAR OF ALL MOVING PARTS.

WARNING: DO NOT ALLOW SMALL CHILDREN ON OR NEAR BED DURING

OPERATION

WARNING: DO NOT ALLOW THIS DEVICE TO BE OPERATED BY SMALL CHILDREN.

WARNING: WHEN OPERATING THE HI/LO, KNEE, OR BACK FUNCTION OF

THE BED, ALWAYS ENSURE THAT THE INDIVIDUAL CONFINED TO THE

BED IS POSITIONED PROPERLY WITHIN THE CONFINES OF THE BED.

DO NOT LET ANY EXTREMITIES PROTRUDE OVER THE SIDE OR

BETWEEN THE BED RAILS WHEN PERFORMING ANY FUNCTIONS.

CAUTION: DO NOT USE UNAUTHORIZED SIDE RAILS. INSTALL SIDE RAILS PER

MANUFACTURER’S INSTRUCTIONS.

CAUTION: WARNING/CAUTION LABELS APPLIED TO THE BED OUTLINE

HAZARDS OR UNSAFE PRACTICES THAT COULD RESULT IN PERSONAL

INJURY AND/OR PROPERTY DAMAGE.

CAUTION: PENDANT HAND CONTROL CORD MUST BE ROUTED AND SECURED

PROPERLY TO ENSURE THAT CORD DOES NOT BECOME ENTANGLED

AND EVENTUALLY SEVERED DURING USE. MAKE SURE ELECTRIC

CORDS DO NOT GET TANGLED AROUND THE BED, SIDE RAILS OR

LEGS DURING NORMAL OPERATING OF THE BED.

CAUTION: WHEN USING NASAL OR MASKED TYPE ADMINISTERING EQUIPMENT,

OXYGEN OR AIR TUBING MUST BE ROUTED AND SECURED PROPERLY

TO ENSURE THAT TUBING DOES NOT BECOME ENTANGLED AND

EVENTUALLY SEVERED DURING NORMAL OPERATION OF BED.

CAUTION: BEFORE OPERATING, ENSURE THAT THE BED FRAME RIVETS ARE

PROPERLY SEATED IN THE BED END HOOKS: OTHERWISE INJURY OR

DAMAGE MAY RESULT.

CAUTION: KEEP ALL MOVING PARTS FREE OR OBSTRUCTIONS (I.E. BLANKETS/

SHEETS, HEATING BLANKETS/PADS, TUBING, WIRING, AND OTHER

TYPES OF PRODUCTS.

WARNING / CAUTION SUMMARY

ASSEMBLY INSTRUCTIONS

HEAD AND FOOT ASSEMBLY

1. Lay the head and foot sections on their sides at approximately right angles to

each other with motor clamps up, as shown below.

2. Slide the head and foot sections together until the foot section’s hook catches

the head section’s rivet on both sides.

ASSEMBLY INSTRUCTIONS

3. Straighten head and foot and position as shown below. Position head wing as

shown below.

CAUTION: WHILE BALANCING FRAME, DO NOT ELEVATE KNEE TOO FAR,

OR LINKAGE MAY OVER-EXTEND AND LOCK. IF LINKAGE LOCKS,

MANUALLY ELEVATE KNEE TO STRAIGHTEN OUT LINKAGE AND

PUSH LARGE LINKAGE PLATE TOWARD FOOT OF BED.

4. Attach foot fabric to head fabric: Attach the foot fabric spring clips to the head

fabric as shown below.

CAUTION: ENSURE THAT HEAD AND FOOT SECTIONS AND SPRING FABRIC

ARE ASSEMBLED AS DESCRIBED ABOVE BEFORE CONTINUING

WITH BED ASSEMBLY.

ASSEMBLY INSTRUCTIONS

MOTOR ASSEMBLY

REMOVE MOTOR SIDE CAPS

1. Remove the slide caps from both ends of the motor as shown below.

Plungers should be recessed in motor cavities; if not, operate “down” function

on the pendant hand control.

NOTE: Motor comes from factory with pendant hand control plugged into motor.

CAUTION: ASSEMBLE MOTOR ON BED AS

FOLLOWS; INCORRECT INSTALLATION

COULD CAUSE BED TO MOVE IN

UNEXPECTED WAYS. MOTOR CAN BE

INSTALLED BACKWARDS.

NOTE: MOTOR IS EMBOSSED WITH

HEAD AND FOOT SYMBOLS (SHOWN

AT RIGHT) AT END OF MOTOR.

2. Install 9V backup battery (not provided) and slide into storage area.

ASSEMBLY INSTRUCTIONS

INSTALL MOTORS

3. Hold the bed securely, positioned with motor cams up, as shown below.

4. Position the motor over both cams.

5. Tap either end of the motor housing (shown below) with enough force to snap

the motor assembly into position on the cam.

Note: This is a bearing surface requiring a tight fit; it may require a hardy hit

with palm of hand to snap over motor tube.

6. Repeat step 5 for other end of motor.

INSTALL MOTOR SLIDE CAPS

7. Position the caps as shown on page 9 so that the grooves in the slide cap are

aligned with the grooves in the motor.

8. Apply straight downward pressure to each end of the cap while sliding into the

closed position.

9. Repeat step 8 for the other cap.

10. Ensure that all four corners of each slide cap are engaged.

ASSEMBLY INSTRUCTIONS

FULL-ELECTRIC AND SEMI-ELECTRIC BED (ALL MODELS)

1. Standing directly in front of the foot bed end, position it as close to the bed

as possible.

2. With one hand, reach over end and lift up bed.

3. Tilt the bed end slightly back toward you.

4. Engage lower rivet slightly with

corner lock and tilt end toward bed.

5. Lower bed onto corner lock.

6. After bed ends have been attached, install bed end safety pins to act as

safety latches

ASSEMBLY INSTRUCTIONS

FULL-ELECTRIC BED ONLY

After installing foot end, you may have to shift bed frame slightly in bed end hooks

to ensure proper horizontal alignment with motor coupling and end gearbox shaft.

When coupling and shaft are aligned, unlock spring-loaded coupling. Coupling may

not snap into groove until motor is rotated with pendant hand control after bed

is assembled.

Plus hi/lo motor into actuator assembly, being careful to route cord with the nylon

tie strap provided under fixed base frame cross-angle (as shown below) to ensure

clearance with hi/lo drive shaft. The motor plug is located next to the pendant

hand control plug on the actuator.

NOTE: Do not tie motor cord to movable knee section crosstube.

FULL-ELECTRIC AND SEMI-ELECTRIC BED

7. Repeat steps 1-6 for head bed end.

ASSEMBLY INSTRUCTIONS

FULL-ELECTRIC AND

SEMI-ELECTRIC BED

Both ends of the hi/lo rod assembly

have a slot to mount on the foot end

and head end gearbox shaft pins (see

picture at right). Follow steps 2-3 to

mount the hi/lo rod assembly on the

gearboxes.

2. Connect the hi/lo rod assembly to

the bed: Attach either end of hi/lo rod

assembly to the foot end gearbox.

3. Attach other end of hi/lo rod

assembly to head end gearbox.

OPERATION INSTRUCTIONS

CRANK OPERATION (SEMI-ELECTRIC BED ONLY)

Use the crank at the center foot of the semi-electric bed to change bed height

(raise or lower entire deck).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Drive Inneneinrichtung Handbücher

Drive

Drive Twin Top Betriebsanleitung

Drive

Drive 13085L Bedienungsanleitung

Drive

Drive Deluxe Overbed table with Tilt-top 13008 Kurzanleitung

Drive

Drive Park House Heathcare PRELUDE 1002070001 Bedienungsanleitung

Drive

Drive RTL10360 Bedienungsanleitung

Drive

Drive Med Aire Plus 8 Bedienungsanleitung

Drive

Drive 13008 Kurzanleitung

Drive

Drive Restwell Benutzerhandbuch

Drive

Drive DELTA PRO 15030N Bedienungsanleitung

Drive

Drive 17100 Bedienungsanleitung

Drive

Drive 13067 Bedienungsanleitung

Drive

Drive 13085L Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung