Drive Inspired GT1000-2GB Bedienungsanleitung
Moxie GT Gait Trainer
Item #s:
GT1000-2GB, GT1000-2GG
GT2000-2GB, GT2000-2GG
GT3000-2GGY
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
by
Your Inspired by Drive branded product is warrantied
to be free of defects in materials and workmanship for
the lifetime of the product for the original consumer
purchaser.
This device was built to exacting standards and
carefully inspected prior to shipment. This Lifetime
Limited Warranty is an expression of our confidence
in the materials and workmanship of our products
and our assurance to the consumer of years of
dependable service.
This warranty does not cover device failure due to
owner misuse or negligence, or normal wear and
tear. The warranty does not extend to non-durable
components, such as rubber accessories, casters,
and grips, which are subject to normal wear and need
periodic replacement.
If you have a question about your Inspired by Drive
device or this warranty, please contact an authorized
Inspired by Drive dealer.
© 2016 Medical Depot, Inc. All rights reserved.
Rev.1.09.21.16
Limited Lifetime Warranty
by
assembly
The GT1000-2GB and GT1000-2GG comes completely
assembled and does not fold
GT2000-2GB, GT2000-2GG & GT3000-2GGY.
1. Remove the Moxie GT from the box.
2. Open gait trainer by lifting top frame until both
latches click into notches (A) in the bottom frame.
adjustments
Height
Pull triggers (B) upwards and slide handlebar to desired
height. Release trigger and move handlebar until triggers
click into place.
B
A
Swivel Lock
Casters can be locked to prevent swivel. Align lever (C)
with one of the two notches in the caster and push lever
into notch.
Wheel Lock
Pressing on bottom part of pedal (D) will lock rotation of
wheels. Pressing on top part of pedal will release wheel
brake.
Wheel Resistance
Lever (E) provides resistance to wheels. Rotating the
lever towards the thinner markings lowers the resistance
and towards the thicker markings adds resistance.
Directional Lever
One-direction use can be achieved by pushing lever (F)
upwards. When one-direction is engaged, there will be a
clicking sound when moving forward and the wheel will
lock when rolled backward.
C
D
E
F
accessories
Most accessories are mounted with the universal mount-
ing bracket. To install the mounting bracket, loosen knob
(G) on clamp and lower it. Lift clamp and place over
handlebar. Bring knob up and tighten. The mounting
bracket can be placed anywhere on the handlebar and it
will depend on the user’s abilities. It can also be mounted
towards the outside or the inside of the handlebar.
Forearm Platforms
Item #s TK 1035 S & TK 1035 L
Install mounting bracket and post at appropriate location.
Place forearm platform on mounting bracket post by loos-
ening knob (H) and placing forearm platform at desired
position.
Forearm platform adjustments
Height – Push in button (I) and slide post to desired posi-
tion. Release button and move forearm platform until it
clicks into place.
Width – Forearm platforms can be placed closer or far-
ther from the user by
• Loosening knob (H) and sliding the forearm platform
outward or inward.
• Place mounting bracket with the clamp facing towards
the outside or inside of the handlebar.
• Position forearm platform posts (J) facing towards the
outside or inside of the handlebar.
Rotation – Loosen knob (H) to rotate up or down and in
or out. It can rotate 360°.
Depth – Loosen knob (H) and slide arm pad forward or
backward or reposition mounting bracket.
• Loosening knob (K) allows the handgrips to extend
forward and backward, supinate and pronate.
• Loosening knob (L) allows wrist angle adjustability.
• Arm strap (M) and wrist strap (N) secures arm.
Handgrips
Item # TK 1045
Install mounting brackets at appropriate location on the
handlebar. They can be mounted with the clamp facing
towards the outside or inside of the handlebar. To adjust
the height, push in button (I) and slide post to desired
position. Release button and move handgrip until it clicks
into place. Handgrips can rotate in four directions.
KM
N
G
I
JHL
G
Ankle Prompts
Item #s TK 1060 S, TK 1060 M & TK 1060 L
Install the ankle prompts by inserting the end of rod into
caster slot, then pull back white trigger (O) and insert
into opposite caster slot. To adjust the stride of the user,
press and slide the spring clips (P) to appropriate length.
To adjust the size of ankle straps use buckle adjuster (Q).
P P
O
Q
Hip Positioner & Pad
Item #s TK 1070 S & TK 1070
Install mounting bracket and handgrips at the back of the
handlebar. Attach the front of the hip positioner towards
the front of the handlebar using buckles (R). Attach the
rear of the hip positioner towards the rear of the handle-
bar by either attaching rings (S) to handgrips or remove
clamp and handgrips and loop straps over rear of handle-
bar. Adjust loop with buckles.
R
T
S
S
U
U
Hip positioner adjustments
Height - rear of the hip positioner - Push in button (T)
and slide handgrip to desired position. Release button
and move handgrip until it clicks into place.
Height – hip positioner – Raise or lower hip positioner by
adjusting the length of the two front and two rear straps.
Depth - Reposition mounting bracket on handlebar.
The hip positioner can be used with or without the pad.
To attach the hip pad, push the rear straps (U) of the hip
positioner through the holes at the back of the pad and
pull into place. Securely snap front and side flaps around
the hip positioner.
REAR
FRONT
T
Trunk Support
Item # TK 1080 S, TK 1080 M & TK 1080 L
Install mounting bracket and post directly behind the
uprights. Loosen knobs (V) on the post and slide chest
prompt rods into the post at desired position. Tighten
knobs.
Trunk support adjustments
The trunk support has two adjustable straps and buckles
on each side. The front of the trunk support also has a
restraining loop to keep the pads together. Each strap is
independently adjustable to adjust the size, fit and angle
of the trunk support.
Height - Push in button (I) and slide post to desired posi-
tion. Release button and move post until it clicks into
place.
Width – Trunk support can be placed closer or farther
from the user by
• Loosening knobs (V) and sliding the trunk support
outward or inward.
• Place mounting bracket with the clamp facing towards
the outside or inside of the handlebar
Depth – Reposition mounting bracket on handlebar.
Rotation – Loosen knobs (V) and tilt trunk support to
desired position. Tighten knobs.
V
V
I
X
W
Y
Thigh Prompts
Item #s TK 1090 S & TK 1090 L
Install thigh prompt clamps on handlebar. It is advisable
to mount them behind the trunk support.
Thigh prompt adjustments
Height – Loosen knob (W) and slide thigh pad (X) up or
down to desired position. Tighten knob.
Width – Thigh pads can be placed closer or farther from
the user by
• Loosening knob (Y), adjust thigh pads inward or
outward and tighten knob
• Place mounting bracket with the clamp facing towards
the outside or inside of the handlebar.
Depth - Reposition mounting bracket on handlebar.
Rotation – Loosen knob (W), rotate the thigh pad and
tighten knob.
Hand Loop
Item # TK 1010
Install mounting bracket at appropriate location on
handlebar. (See instructions on Page 3) They should be
installed towards the front of the uprights. This provides
stability and ample room for other accessories.
Insert Hand Loop assembly into mounting bracket with
knob (A) facing away from user.
B
A
Guide Bar
Item # TK 1020
Turn knob (C) counterclockwise to open clamp. Install
the Guide Bar on the center of the front top handlebar.
Tighten knob to secure Guide Bar.
Adjustments
Loosen knob (C) and rotate Guide Bar until it is behind
the user for pushing or in front for pulling. Tighten knob
to secure at desired position.
C
Periodically clean the hip positioner, pelvic support,
chest prompt, arm prompt pads with a damp rag and
a mild disinfectant. Remove lint from hook and loop as
needed.
Wash casters with water after outdoor use. Avoid mud
and sand. Do not use petroleum-based or solvent-based
lubricants on casters, but lubricate when necessary with
silicone spray or graphite.
Twice a year inspect straps and padding for damage, and
replace if necessary. Periodically inspect for breaks,
loose parts, missing parts, cracks and/or malfunctions.
Remove the product from service when any condition
develops that might make operation unsafe.
TK 1020
TK 1010
cleaning
maintenance
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Drive Mobilitätshilfe Handbücher
Drive
Drive PATRIOT Series Bedienungsanleitung
Drive
Drive GoLite 200 Bedienungsanleitung
Drive
Drive R800RD Bedienungsanleitung
Drive
Drive Road Bedienungsanleitung
Drive
Drive Cristallo Bedienungsanleitung
Drive
Drive Nitro RTL10266 Bedienungsanleitung
Drive
Drive Dr.K Go/Lite 10209RD-1 Installationsanleitung
Drive
Drive 10350-1 Bedienungsanleitung
Drive
Drive 10247-4 Bedienungsanleitung
Drive
Drive DUPONT MADRID Bedienungsanleitung
Drive
Drive 11148N-4 Bedienungsanleitung
Drive
Drive arc lite 102EXL-BL Bedienungsanleitung
Drive
Drive FC 2029 Handbuch
Drive
Drive DeVilbiss Bedienungsanleitung
Drive
Drive TW011R Bedienungsanleitung
Drive
Drive 721 100 100 Bedienungsanleitung
Drive
Drive RTL10266BK Bedienungsanleitung
Drive
Drive Dart 3 Wheel Bedienungsanleitung
Drive
Drive Clever-Lite LS Installationsanleitung
Drive
Drive Torro Bedienungsanleitung
Beliebte Mobilitätshilfe Handbücher anderer Marken
AMF-BRUNS
AMF-BRUNS PROTEKTOR Bedienungsanleitung
Drive DeVilbiss Healthcare
Drive DeVilbiss Healthcare OTTER Bedienungsanleitung
Rhythm Healthcare
Rhythm Healthcare C500U Bedienungsanleitung
Lumex
Lumex RJ4200A Bedienungsanleitung
Rebotec
Rebotec Jumbo Bedienungsanleitung
Rehaforum MEDICAL
Rehaforum MEDICAL PR50548 Bedienungsanleitung