DSC PC6204HC Bedienungsanleitung

PC6204HC High Current

Relay Output Module Installation Instructions

Please refer to the System Installation Manual for information on limitations regarding product

use and function and information on the limitations as to liability of the manufacturer.

1. Introduction

The PC6204 is an output module with four programmable

relay outputs. Relay 1 can be used to repower the Combus.

NOTE: Do not use any power supply other than the PC6204

to repower the Combus. If a power supply other than the

PC6204 is used, the Combus repower function will not

operate as intended. See the control panel System Manual

for details regarding this feature.

2. Specifications

• 2.2A Power Supply

• Current Draw: 30 mA (from Combus)

• Minimum 80VA 16-18V transformer required

• Minimum 7Ah battery required up to 36Ah max.

• Connects to control panel via 4-wire Combus

• Four programmable relay contacts rated 2A, 30VDC

• AUX current: 1.2A with low charging current

800mA with high charging current

• Tamper contact input

• Selectable battery charging current (800mA or 1.2A)

• Up to16 modules per system

Compatible Cabinets

• PC4003C

• PC4006C

3. Installing the PC6204

3.1 Unpacking

The PC6204 package should include the following parts:

• One PC6204 circuit board

• One ground wire assembly

• Five plastic stand-offs

• One 5A replacement fuse

3.2 Mounting

The PC6204 should be located inside a compatible cabinet,

mounted in a dry, secure location. Preferably, it should be

placed at a convenient distance from the connected devices.

Perform the following steps to mount the unit:

1. Press the five plastic stand-offs through the mounting holes

at back of the cabinet.

2. Secure the cabinet to the wall in the desired location. Use

appropriate wall anchors when securing the cabinet to

drywall, plaster, concrete, brick or other surfaces.

3. Press the circuit board into the plastic stand-offs to secure

the module to the cabinet.

Once the unit is mounted, wiring may be completed.

3.3 Installation and Wiring

Before beginning to wire the unit, ensure that all power (AC

transformer and battery) is disconnected from the control

panel.

Perform the following steps to complete wiring:

1. Connect the four Combus wires to the PC6204. Connect

the red, black, yellow and green Combus wires to the RED,

BLK, YEL and GRN terminals, respectively.

If Relay 1 is being used for Combus Power, connect the

Combus wires according to the following diagram. Note

that for this option, Jumper J1 must also be set for

“Combus Relay.”

CONTROL

PANEL

NOTES:

1. The connection to the mains supply must be made as

per the local authorities’ rules and regulations. In the UK,

as per BS6701.

2. If during the installation a knockout is removed, it is

the installer’s responsibility to ensure that the same degree

of protection for the cabinet is provided by the use of

bushings, fittings, etc.

3. The cabinet must be secured to the building structure

before operation.

4. The equipment is intended to be installed by SERVICE

PERSONNEL ONLY or equivalent (e.g.: persons having

appropriate technical training and experience necessary to

be aware of hazards to which they are exposed in

performing that task.

5. Internal wiring shall be routed in a manner that

prevents:

- excessive strain on wire and on terminal connections;

- loosening of terminal connections;

- damage of conductor insulation.

6. The external power supply shall meet the applicable

requirements of the Low Voltage Directive.

Security Products

Toronto, Canada

1-800-387-3630 • www.dscgrp.com Printed in Canada 29004924 R001

2. Complete all output wiring.

3. Connect the external tamper switch, if used.

Consult the above wiring diagrams for further information.

3.4 Applying Power

After all wiring is completed, apply power to the control panel.

Connect the battery leads to the battery, then connect the AC

transformer. Then, connect power to thePC6204: the battery

leads followed by the AC transformer. For more information

on control panel power specifications, see the control panel

System Manual.

NOTE: Do not connect the power until all wiring is complete.

4. Enrolling the Module

NOTE: By default, before you can enroll modules, or change

any system programming, a user must tell the system to

“Allow System Service”. The system will then allow access to

Installer’s Programming for 60 minutes. Any user with a

Master code can tell the system to allow service at a system

keypad. The default Master code is [1234].

See the Maintenance Manual for more information. See the

Programming Manual – “Download Section” for more

information on the “User Allows Serv” toggle option.

Once all wiring is complete, the module must be enrolled on

the system. To enroll the module, perform the following:

1. Pressing [*] [8] [Installer’s Code].

PC6204 Outputs

4204 Options 0 - 06 - 2 - 01➔➔

➔➔

➔16

Module Number: PC6204 # I

______I______I

Area Date Pulse Alarm Seismic

No. Output*

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Zone Schedule Timer Group Group

_____I_____II

____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I_____I____I____I____I____I____II

_____I_____I_____II

_____I_____II

_____I_____I

2I_____I_____II

____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I_____I____I____I____I____I____II

_____I_____I_____II

_____I_____II

_____I_____I

3I_____I_____II

____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I_____I____I____I____I____I____II

_____I_____I_____II

_____I_____II

_____I_____I

4I_____I_____II

____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I____I_____I____I____I____I____I____II

_____I_____I_____II

_____I_____II

_____I_____I

* List of Output Options:

[00] Fire and Burg [11] Courtesy Pulse [22] Exit Follow [33] Battery Test [44] Inv Date Sched

[01] Inv Fire/Burg [12] Chime Follower [23] Entry Follow [34] Auxiliary Alrm [45] Inv Hold Up

[02] Burg Only [13] TLM Only [24] Date Schedule [35] Medical alarm [46] Inv Set

[03] Inv Burg Only [14] Failure to Comm [25] Hold Up [36] Seismic Pulse [47] Inv Tbl Group

[04] Fire Only [15] Combus Power [26] Set [37] Alarm Group [48] Inv Tamper

[05] Inv Fire Only [16] Ready Status [27] Trouble Group [38] Inv Area Status [49] Inv Cond. Al.

[06] Utility Output [17] Zone Alarm [28] Tamper [39] Inv Latch Strobe [50] Inv Police Code

[07] Sensor Reset [18] Zone Follow [29] Condition. Al. [40] Inv Trouble O/P [51] Inv Aux Alm

[08] Area Status [19] Duress Output [30] Police code [41] Inv Zn Alarm [52] Inv Medical Alm

[09] Latched Strobe [20] Buzzer Follow [31] Momentary O/P [42] Inv Zn Follow [53] Inv Seismic O/P

[10] Trouble Output [21] Remote Operation [32] Maintained O/P [43] Inv Duress O/P [54] Inv Alarm Group

[55] APS Controlled

2. Scroll to “Module Hardware” and press the [*] key.

3. Scroll to “Enroll Module” and press the [*] key.

4. Scroll through the different modules until “PC6204” is

displayed. Press the [*] key.

5. The message “Create Tamper on Desired Unit” will be

displayed. To create the required tamper, secure the tamper

zone on the module and then open it. The transition from

secure to violated enrolls the module. After this is done, the

keypad will display the module number and will confirm

enrollment (e.g. “PC6204 Mod 01 Enrolled”).

For more information regarding module enrollment, see the

control panel System Manual.

5. Programming the Module

To access PC6010 programming, have a user allow system

service, then enter [*][8] followed by the Installer’s code. Each

relay output must be programmed. The programming

worksheet located below indicates which sections must be

programmed. For more information regarding how to

program, see the control panel System Manual.

NOTE: The output options listed below are for PC6010 v2.0.

For programming other software versions, see the

corresponding programming manual.

NOTE: If you will be using Relay 1 for Combus Power, make

sure that you program the output for option [15] Combus

Power, and that you set jumper J1 to “Combus Relay”.

Andere DSC E/A-System Handbücher

DSC

DSC AMP-701NP Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung