DSC PC2550 Bedienungsanleitung

Code Changes

User’s Programming Commands

[*]+[5]+[MASTER CODE]

The [*][5] user’s programming commands are used to program additional access codes. Up to 16 user arm-

disarm codes may be programmed. The 1st code is the Master Code (factory default [1234]). The 16th code

is optionally a “One Time Use”or maid code. The 16th code may be changed from a “One Time Use” code to

a regular code using an installer’s programming command (section [15]...light 8). Remember if no keypad

entry is made for more than 2 minutes the keypad will return to the normal arm-disarm display and the

complete command will have to be re-entered to program a new access code.

Programming Additional Access Codes

1. Press the [*] and [5] keys then enter the Master Security Code (default [1234]) to enter the additional code

programming mode. The “Program” light and “Zone 1” light will be on to show that the rst code (the Master

Code) is already programmed with the factory default code [1234]. The Master Code may be changed but do

not try to erase the Master Code. The installer can disable user changing of the Master Code by turning on

light 2 in section [16].

2. 15 additional codes may be programmed. The zone lights are used to indicate which of these codes are

already programmed (zone light on steady) and the one which is currently being programmed (zone light is

ashing).

3. To program the second code, press [2] and zone 2 light will ash. Then enter a 4 digit code and the buzzer

will beep three times and zone light 2 will come on steady indicating a programmed code.

4. To remove the second code, press [2] - the buzzer will beep three times and zone light 2 will ash. Enter

[*] [*] [*] [*], the buzzer will beep three times and zone 2 light will go out to show that the code has been

removed.

5. Follow the instructions in 3 or 4 for programming or removing any of the other additional codes.

6. To program access codes 9 to 16, press 9 to toggle into the upper code region. Zone lights 1 to 8 now rep-

resent access codes 9 to 16 (light 1 is code 9.... light 8 is code 16). The “Ready” and “Armed” LEDs will ash to

indicate that the user is in the upper programming region. Program or remove access codes 9 to 16 as stated

in 3 and 4 above. Press 9 again to toggle back down to the lower region (access codes 1 to 8).

7. Do not try to remove the Master Code (1st code). The Master Code may be changed but it must not be

removed. When changing the Master Code be sure to enter a valid 4 digit number (use only number keys 0

to 9). Do not enter [#] or [*] as one of the digits. If the Master Code is forgotten and the panel is left disarmed,

program a new Master Code using the [*][8][Installer’s Code][25] command. If the Master Code is forgotten

and the panel is left armed, use the 2nd Master Code to disarm the system. If the 2nd Master Code is not

programmed then the entire programming can be reset to factory default by using the “Hardware Reset”

method described on page 24.

8. To successfully program or remove additional codes, the panel must be put into the code program mode

by following step 1 followed by steps 3 or 4. Note that if no key entry is made for 2 minutes the panel will go

back to the normal arm/disarm mode, after which step 1 must be repeated to get back into the code pro-

gram mode.

9. To exit the code program mode press [#].

To review:

programming a new code;

enter [*] [5] [Master Code] [1 to 8] [4 digit code], or

[*] [5] [Master Code] [9] [1 to 8] [4 digit code]

eliminating an existing code;

enter [*] [5] [Master Code] [2 to 8] [* * * *], or

[*] [5] [Master Code] [9] [1 to 8] [* * * *].

Note: The access code numbers must be entered as

one digit. E.g. 2, 3,......, 7, 8.

Andere Handbücher für PC2550

Inhaltsverzeichnis

Andere DSC Sicherheitssystem Handbücher

DSC

DSC Impassa WT4911 Bedienungsanleitung

DSC

DSC WLS900 Bedienungsanleitung

DSC

DSC MAXSYS PC4020 Bedienungsanleitung

DSC

DSC PowerSeries PC1404 Bedienungsanleitung

DSC

DSC PowerSeries PC1404 Bedienungsanleitung

DSC

DSC Power832 Fehlerbehebungshandbuch

DSC

DSC PC 4010 Betriebsanleitung

DSC

DSC PK5500/RFK5500 Bedienungsanleitung

DSC

DSC iOtega Bedienungsanleitung

DSC

DSC PC2580 Bedienungsanleitung

DSC

DSC MAXSYS PC4020 Bedienungsanleitung

DSC

DSC Power432 PC585 Bedienungsanleitung

DSC

DSC PC2550 Bedienungsanleitung

DSC

DSC Power 832 PC5010 Bedienungsanleitung

DSC

DSC WS4965 Bedienungsanleitung

DSC

DSC Power608 Bedienungsanleitung

DSC

DSC Power632 Bedienungsanleitung

DSC

DSC PC15OO Bedienungsanleitung

DSC

DSC neo HS2016 Bedienungsanleitung

DSC

DSC Power832PC5010 CP-01 Bedienungsanleitung

DSC

DSC PC5010 V2.0 Bedienungsanleitung

DSC

DSC Power Series Bedienungsanleitung

DSC

DSC Power 864 Bedienungsanleitung

DSC

DSC PowerSeries Neo HS2128 E Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung