DSC LINKS1000 Bedienungsanleitung

CONTENTS

LINKS1000 GLOSSARY OF TERMS 2

INTRODUCING THE LINKS1000 3

Specifications.................................................... 3

HOW THE LINKS1000 WORKS 4

Cellular Communications .................................. 4

Sending an alarm .............................................. 4

Telephone Line Monitor .................................... 4

Trouble supervision........................................... 4

Downloading ..................................................... 5

Emergency Phone Number ............................... 5

Powering the LINKS1000 from a DC Source .... 5

Using the Keypad ............................................. 6

SETTING UP THE PROGRAMMER 6

LINKS1000 PROGRAMMING GUIDE 7

Arranging for Cellular Service........................... 7

Using the LINKS1000 Programmer................... 7

Programming the LINKS1000 ........................... 8

Disconnecting the LINKS1000 Programmer..... 8

INSTALLATION 10

Mounting the Cabinet...................................... 10

Mounting the Antenna..................................... 10

Wiring Connections......................................... 10

“AC” Power Terminals ..................................... 10

Ground Connection......................................... 11

Tamper Terminal ............................................. 11

Supervision of LINKS-to-Panel Connection .... 11

LINKSSYSTBLTerminal ................................ 11

AUX IN Terminal.............................................. 11

LINKS PGMIn Terminal - Serial Input for Central

Station Telephone Number ............................. 11

Telephone Terminals....................................... 12

LINKS RING Terminal Allows Panel to be

Downloaded via LINKS ................................... 12

Bat TBL Terminal............................................. 12

AC TBL Terminal ............................................. 13

Battery Connections........................................ 13

Jumper J1 ....................................................... 13

Jumper J2 ....................................................... 13

HOOK-UP DIAGRAM -

PC1500/1550/2525/2550/3000 14

HOOK-UP DIAGRAM - PC1575/PC1580/

PC5010/PC5015/PC1555/PC1565/

PC5008/PC580/PC585 15

HOOK-UP DIAGRAM -

PC4010/PC4020/PC4020KT 16

HOOK-UP DIAGRAM -

P16LC / P1664 / DC1664LC 17

RELOCATING THE ANTENNA 18

PROGRAMMING CONTROL PANELS FOR

LINKS1000 19

Preamble Section of Control Panel

Programming................................................... 19

Communication Formats ................................. 19

PC1500 and PC1550 Control Panels .............. 20

PC1575/PC1580ControlPanel ....................... 20

PC2525 Control Panel ..................................... 20

PC2550 Control Panel ..................................... 21

PC3000 Control Panel ..................................... 21

PC4010, PC4020 and PC4020KT

Control Panels ................................................. 21

PC5010/PC5015/PC1555/PC1565/

PC5008/PC580/PC585ControlPanel ............. 23

Sur-Gard DC1664LC ....................................... 24

Sur-Gard P16LC .............................................. 24

Sur-Gard P1664 .............................................. 25

Power-up Procedure ....................................... 25

TESTING THE SYSTEM 25

Performing a LINKS Test Transmission .......... 25

“On Air” Indication .......................................... 26

20-minute Transmission Cut-off ...................... 26

LINKS1000 TROUBLE SHOOTING 26

LINKS TROUBLE SUPERVISION 27

Reading trouble conditions on the LINKS1000

via the LINKS1000 Programmer ..................... 28

and are trademarks of the DSC Group of Companies.

LINKS1000 GLOSSARY OF TERMS

The following is a description of various terms used with regards to cellular technology.

Electronic Serial Number (ESN)

The ESN is the unique serial number of a cellular phone. It is used by the cellular network to track calls and

increment billing. The ESN is stored at the time of manufacture and cannot be reprogrammed. This number,

in either hexadecimal or decimal, must be loaded into the database of the cellular carrier before service can

begin.

Cellular Phone Number and Area Code

A 10 digit number (3 digit area code and 7 digit directory number ) identifying the cellular telephone. Do not

enter the phone number of the central monitoring station as the cellular phone number when programming

the LINKS1000.

Initial Paging Channel

A three digit number that specifies which ‘Side’ carrier you have contracted for service. Each cellular service

area only has two sides, A or B. The initial paging channel for Side A is ‘333’ and for Side B is ‘334’.

System ID

Also called the Home Access ID, this 5 digit number identifies the customer's predefined ‘Home System’. This

number refers to a geographic area and is used by the cellular carrier to determine if the unit is ‘Home’ or in

‘Roam’.

Access Overload Class

This is the number that specifies the level of priority of the cellular call. There is no correlation between this

number and the level of cellular service unless there is a network emergency.

Group Identification Mark

This number is factory programmed and specifies how many bits of the System ID are compared when

processing signals. The Group Mark ID for LINKS1000 is set at 10. This number will make the LINKS1000

compatible with all North American networks.

Preferred System Mark

This number is determined by the Initial Paging Channel and refers to which system, A or B, is scanned for

first.

Roam/Roaming

Using cellular service outside of one ‘Home’ area. Usage charges are higher when Roaming.

INTRODUCING THE

The LINKS1000 Cellular Alarm Transmitter enhances the protection provided by a security system by

providing a reliable backup to the control panel’s normal telephone communications with the monitoring

station. The LINKS1000 works with the DSC and Sur-Gard Security Control Panels described in the

Specifications below.

If the control panel is unable to complete an alarm transmission through the normal telephone line, due to any

line problems, the LINKS1000 will be activated and will transmit the alarm communication over the cellular

network. The LINKS1000 works automatically.

The LINKS1000 has been designed for simple and straightforward installation. Wiring connections are made

directlybetweentheLINKSunitand the securitycontrol panel.The DSCand Sur-GardSecurityControlPanels

require only minor changes in their Programming Sections

Specifications

Compatible control panels

• DSC PC1500/PC1550 software version 4.0 or later

• DSC PC1575/PC1580 software version 1.0 or later

• DSC PC2525 software version 1.0 or later

• DSC PC2550 software version 1.2 or later

• DSC PC3000 software version 7.6 or later

• DSC PC4010 software version 1.0 or later

• DSC PC4020 software version 1.0 or later

• DSC PC4020KT software version 1.0 or later

• DSC PC5010 software version 1.0 or later

• DSC PC5015 software version 2.2 or later (w/Downlook)

• DSC PC1555/PC1565/PC5008 software version 2.0 or later

• DSC PC580/PC585 software version 2.1 or later

• Sur-Gard DC1664LC software version 3.6 or later (requires MEX2 Module)

• Sur-Gard P16LC and P1664LC software versions 2.0 or later

UL has only verified compatibility with the PC4020 and PC5010.

Communication Method

• Amps cellular telephone network

RF Power Output

• 3.0 Watts maximum

Antenna

• 3 - 5 dB gain, TNC connector

Battery

• 12 volt 7 Ah minimum rechargeable gel-cell type battery

Transformer

• 16.5 VAC, 40 VA

Dimensions

• 11" × 11.8" × 3.3" (279 mm × 300 mm × 84 mm)

Weight

• 6.5 lbs. (3 kg)

IMPORTANT NOTE

Asecuritysystemcannotpreventemergencies.Itisonlyintendedtoalertyouand,ifincluded,amonitoring

station,ofanemergencysituation.Securitysystemsaregenerallyveryreliablebuttheymaynotworkunder

allconditionsandtheyarenotasubstituteforprudentsecuritypracticesorlifeandpropertyinsurance.Your

security system should be installed and serviced by qualified security professionals who should instruct

you on the level of protection that has been provided and on system operations.

HOW THE LINKS1000 WORKS

Cellular Communications

All cellular telephones, including the LINKS1000, must ‘register’ with the cellular network. ‘Registration’ is

simply a handshake, sending ESN and Telephone number, between the cellular switching station and the

cellular telephone. This is done upon power up of the LINKS1000 and randomly once a day. If the phone does

not register the network will not complete a call. Tower signal strength, also called RSSI (receive signal

strength indication) is updated approximately every 4-5 seconds. RSSI is indicated as a go/no go visible via

the RSSI LEDs (L3, L4, L5, L6).

Sending an alarm

Before dialing the central station, all DSC alarm controls perform a telephone ‘line-test’. This is done via the

control unit using a series of off-hook and on-hook transitions to verify dial-tone. This takes 30 seconds.

The control panel ‘line-test’ feature will only determine a telephone line is inoperative when it is attempting to

sendan alarm.WithaLINKS1000 connected,thecontrolpanel willsendthe central stationtelephonenumber,

in a digital format, from the PGM output of the control panel to the PGMIn input of the LINKS1000. The

LINKS1000 then accesses the cellular telephone network and begins dialing. Once a suitable channel is

established the LINKS1000 switches an onboard relay and establishes a connection between the TIP and

RING terminals on the control panel and the T1 and R1 terminals on the LINKS1000.

With cellular communications now open to the central station receiver, the panel will detect ‘handshake’. The

alarm is sent. If the message is received, ‘kiss-off’ is sent, just as if it were communicating over a standard

telephone line. Once the panel has completed the transmission, the control panel ‘hangs up’. The LINKS1000

then detects the loss of current across T1 and R1 and sends the END key to the cellular network.

Telephone Line Monitor

TheTelephone LineMonitorisa separatefeatureintegral toDSCor Sur-gard controlpanelsPC1575, PC1580

and higher. The TLM looks for a 30 second loss of telco line voltage. With a LINKS1000 connected and TLM

signaling enabled, a service outage would trigger the panel to begin dialing though the LINKS1000. Dialing

will begin after the TLM time-out and ‘line-test’ are complete. This should take 1 minute.

Trouble supervision

Trouble supervision of the LINKS1000 is provided in one of two ways:

When Jumper J1 is ON (shorted), a general system trouble indication is used at the LINKS1000 SYS TBL

terminal. All trouble indications will trigger this output to the control panel.

When Jumper J1 is OFF (removed), there are three separate trouble outputs: AC TBL, Bat TBL, and the

LINKS1000 SYS TBL. The AC TBL terminal and Bat TBL terminals are each used to indicate their respective

troubles. The LINKS1000 SYS TBL will activate for all other troubles. These outputs are connected from the

LINKS1000 terminals to separate zones on the control panel. The zone(s) should be programmed as 24-hour

silent except on the PC1575, PC1580, PC4010, PC4020, PC4020KT, PC5010, PC5015, PC1555, PC1565,

PC5008, PC580 and PC585 where a zone (or zones) is designated for LINKS1000 supervisory. Under normal

conditions, the TBL outputs of the LINKS1000 are “open”. When one or more of the six monitored trouble

conditions are present, and the corresponding time-out has expired, the respective output will be pulled to

ground. The connection from the LINKS1000 TBL output to the control panel zone, forces the zone to ground.

The panel now has an alarm it must send and the dialing sequence begins. Typically, trouble signals are sent

via the telco line. If the telephone line is not operational, the panel will send the signal via the LINKS1000 and

the cellular network.

This configuration is required on UL Listed systems.

Downloading

Downloading an alarm control via the LINKS1000 requires connecting the RING terminal on the LINKS1000

to the proper terminal on the control panel (see instructions). Then, from the downloading computer, simply

dial the cellular telephone number of the LINKS1000. The LINKS detects an incoming call and pulls the RING

terminal to 12 VDC. This instructs the alarm control to answer, the panel then provides continuity across TIP

and RING. The LINKS detects current flow and connects the LINKS T1 and R1 and the panel TIP and RING.

Upon completion of downloading, the LINKS1000 will ‘hang up’. The LINKS1000 will automatically disconnect

any call after a 20 minute duration.

Emergency Phone Number

This number is programmed into the LINKS1000 and will be dialed when the AUX IN terminal is shorted to

ground. To program the number, enter the emergency phone number into the LINKS1000, exactly as it would

be dialed on a cellular phone. To use this feature, place an ordinary handset in parallel with the panel on the

LINKS1000 T-1, R-1 terminals and connect a normally open pushbutton across the AUX IN and Ground

terminals.

NOTE

: This input is a 24-hour, silent terminal and the Panic phone call will be connected through the cellular

network.

Powering the LINKS1000 from a DC Source

The LINKS1000 (v3.0 and higher) has the capability to be powered only by a DC source. This could be useful

in such applications as: large recreational vehicles, motor homes, transport trucks, large boats, etc. In these

cases, the main power source is the vehicle’s battery and DC electrical system with no true AC source for the

control panel or LINKS1000 to draw power from.

To use the LINKS1000 with only a DC source, short jumper J2 and leave in place. Connect all wiring for the

LINKS1000 except for the power circuit. Once all connections are made, connect the vehicle’s DC source to

the battery leads of the LINKS1000 (observing correct polarity) and test the control panel and LINKS1000

according to the “Testing the System” sections of their respective manuals.

NOTE

: If the LINKS1000 is being used for such an application, the central station should be notified when the

vehicle is being serviced to avoid possible false alarms.

NOTE

: The LINKS1000, control panel and DC source should be in a physically secure location to avoid

possible tampering.

WARNING: Though the Links1000 product is capable of roaming, this is fully dependant on the service

provider.

This configuration should not be used on UL Listed systems.

Install 4 AA batteries in the LINKS1000 Programmer, being sure to note proper orientation. If the batteries are

installed incorrectly, the Programmer will not function.

Using the Keypad

Operation of the Programmer is as simple as scrolling through the menu to find the desired programming

option and pressing the [✱✱

✱✱

✱] Key to select the option.

• Use the and keys to scroll through the menu displays to locate the desired menu or programming item

• When the screen displays the desired menu item or programming option, press the [✱✱

✱✱

✱] Key to select the

item or option

• The Programmer will automatically shut itself off if there is no keypad activity for a period of 2 minutes.

NOTE

: The LINKS1000 will not function until the Programmer is unplugged from it.

ProgrammerLowBatteryIndication

If the Programmer’s batteries begin to run low, this message will be displayed:

*PROGRAMMER *

*LOW BATTERY *

The low battery message will remain on the screen for 3 seconds or until it is acknowledged by pressing any

key while it is displayed. If a key is pressed while the message is displayed, the message will not reappear

for the rest of the programming session.

If the message is not acknowledged, it will be removed from the screen after 3 seconds; the next time a key

is pressed, the low battery message will again be displayed.

SETTING UP THE PROGRAMMER

ArrangingforCellularService

In order for the LINKS1000 to communicate via the cellular telephone network, an account must be set up with

a cellular network operator. The ‘account’ is simply a matter of establishing the billing information for the

cellular service. In return, the cellular carrier will provide you with the

cellular telephone number.

Cellular

service may vary in price and coverage. Check with your cellular service provider for area coverage maps

and service charges.

Any cellular telephone service provider may be used as the LINKS1000 is compatible with all AMPS type

cellular telephone networks. There are a maximum of two separate network operators in a given market. They

are called non-wireline carriers (A-Side) and wireline carriers (B-Side). Choose the carrier and rate plan that

best fits the application.

DSC is not a cellular service provider, however the LINKS1000 is licensed to use the ‘HELPTEL’ cellular

service rate offered by LINDSAY Communications of Loeminster, Massachusetts. This coverage is virtually

nation wide, using exclusively A-side carriers, and offers service rates that are designed for cellular

applications requiring minimal air time. (In most applications the LINKS1000 is configured to activate only

when the alarm is set and the protected premises experiences an unanticipated loss of dial tone.) LINDSAY

Communications can be reached at 1-800-878-9898. For answers to any other questions concerning cellular

activation call 1-888-623-7873.

Note: When using LINDSAY Communication for cellular service, pay close attention to the PREAMBLE

Section when programming the control panel.

Using the LINKS1000 Programmer

The LINKS1000 Programmer is used to enter the required cellular network parameters into the LINKS1000.

If the parameters are not entered correctly, the LINKS1000 will not operate.

AC power must be applied to the LINKS1000 in order to program any data.

Connect the modular connector of the Programmer to the modular jack on the LINKS1000. Press any key to

activate the Programmer. The LCD screen will light up.

Note:

If the screen does not light up, check to see if 4 AA batteries were correctly installed in the back of

the Programmer.

The LINKS1000 Programmer is menu driven (see Table 1 for a list of menu messages):

• use ‘up’ and ‘down’ arrows to scroll through the various menu fields

• when the desired field is displayed, use the [✱✱

✱✱

✱] key to select it

• or use the numbers shown in parentheses to go directly to the desired menu or item

• use the [#] key to enter data and exit the section.

Before a cellular service provider will give the Cellular Phone parameters, you must first give the LINKS1000

Electronic Serial Number (ESN). The ESN is found on the LINKS itself (in hexadecimal), or can be read via the

Programmer (in hexadecimal).

If the ESN was not found on the LINKS1000, scroll to the “Read LINKS” menu. Select the ESN and the LCD

will display the ESN in hexadecimal form.

Record the ESN here: l_____l_____l- l_____l_____l_____l_____l_____l_____l

The following parameters must be obtained from the Cellular carrier:

• The cellular telephone number for the LINKS l_____l_____l_____l-l_____l_____l_____l-l_____l_____l_____l_____l

• The System I.D. l_____l_____l_____l_____l_____l

• The Initial Paging Channel l_____l_____l_____l

LINKS1000 PROGRAMMING GUIDE

ProgrammingtheLINKS1000

Step 1.

Programming the Cellular Telephone Number

Scroll to “Write LINKS” and press [✱✱

✱✱

✱] to select. Scroll to “LINKS Phone #” and press [✱✱

✱✱

✱] to select.

Enter the area code and phone number for the LINKS. Press [#] to store and exit.

Step 2.

Program the Cellular Network Parameters

While still in “Write LINKS” menu, scroll to “System I.D.” and press [✱✱

✱✱

✱] to select. Enter the five digit

System I.D. number. Press [#] to store and exit.

Scrollto the“InitialPage” andpress[✱✱

✱✱

✱]to select.Chooseeither“A SIDE333”or“B SIDE334”using

the and keys. Press [#] to store and exit.

Scroll to “Access Class” and press [✱✱

✱✱

✱] to select. (This is automatically set by the Programmer.)

Press [#] to store and exit.

Step 3.

Enabling Downloading

Whilestill inthe“WriteLINKS” menu,scrollto “Downloading?”andpress [✱✱

✱✱

✱]to select.Usingthe

and keys, choose either “Enabled” or “Disabled”. Press [#] to store and exit.

Only LINKS1000 version 2.10 or higher will support this function. This option will display on

non-supported versions, but will not be accessible.

NOTE:

With the Downloading feature “Enabled,” the LINKS1000 will answer ANY call placed to the

LINKS1000 cellular telephone number, therefore generating cellular charges. If Downloading via the

LINKS1000 will not be used, the Downloading feature must be disabled.

Step 4.

AC Failure Reporting Option

The option of sending an AC failure is done via the AC Failure reporting display. Scroll to the ‘AC

Tbl Sent?’ screen and press [✱✱

✱✱

✱]. Press the and keys to toggle either ‘Enable’ or ‘Disable’.

Press [#] to store and exit.

With the option ‘Enabled’ the LINKS1000 WILL report loss of AC power.

With the option ‘Disabled’ the LINKS1000 WILL NOT report loss of AC power.

Only LINKS1000 version 2.20 or higher will support this function. This option will display on

non-supported versions, but will not be accessible.

Step 5.

Emergency Phone Number

TheAUXINterminalprovidesaPanictypealarmtotheLINKS1000.Whenthisterminalisbrieflyshorted

to ground, the LINKS1000 will dial the phone number that is programmed in the emergency phone

number location.

Only LINKS1000 version 3.0 or higher will support this function. This option will display on

non-supported versions, but will not be accessible.

NOTE

: This input is a 24-hour, silent terminal and the Panic phone call will be connected through the

cellular network.

Select the LINKS Write menu, then select the Emergency Phone Number item.

Enter the phone number exactly as it would be dialed on a standard cellular phone. Press [#] to

exit the item and store the phone number into the LINKS1000 memory. (See “How the LINKS1000

Works” for instructions on how to connect a phone to the LINKS1000 for use with the emergency

phone number.)

Disconnecting the LINKS1000 Programmer

Step 1.

Scroll to “Main Menu”.

Step 2.

Press [#], wait for the display to go blank.

Step 3.

Disconnect the modular cord from the LINKS1000. Done

NOTE

: Unplug the Programmer from the LINKS1000 when finished programming. The LINKS1000 will not

operate when the Programmer is plugged in.

Table 1 — List of LINKS1000 Programmer Menu Messages

Main Menu

(0) Write LINKS (1) Trouble (2) Read LINKS

(0) LINKS Phone #(0) LINKS Phone #

(1) System I.D. (1) ESN

(2) Initial Page (2) System I.D.

(3) Access Class (3) Initial Page

(4) Downloading (4) Access Class

(5) AC TBL Sent (5) Group ID Mark

(6) Emergency Phone # (6) Prefrd Sys Mark

(7) Downloading

(8) AC TBL Sent

(9) Emergency Phone #

See Table 3 on page 28

for Trouble Messages

and explanations

MountingtheCabinet

It is important to mount the LINKS1000 as close to the DSC / Sur-gard alarm control panel as possible

3 feet is the recommended maximum distance between the two devices. If the devices are mounted in an

under-over arrangement, always mount the LINKS1000 on top. It is recommended that all wiring between the

control panel and the LINKS1000 be in a tamper and attack-resistant conduit.

Keep in mind the LINKS1000 antenna must be mounted above ground level. If necessary, Antenna

Extension Kits are available from your distributor. Remember cellular likes height. The antenna should be

installed in a physically secured location to avoid tampering.

As much as reasonably possible the LINKS1000 should not be located near sources of interference. These sources

includeEMI generatedby televisions orheavy electricmotorssuch asthosefound inheating or airconditioning units.

Removeprinted circuitboard andwallmounting hardwarefrom cardboard retainerinside cabinet.Beforeattaching

the cabinet to the wall, press the white nylon mounting studs through the holes in the back of the cabinet.

Mounting the Antenna

NOTE:

An antenna should always be connected to the LINKS1000 whenever it is operated. The unit will not

function properly if an antenna is not installed.

Before attaching the antenna, first secure the TNC connector and cable attached to the LINKS unit in the hole

in the top of the cabinet using the hardware provided. Ensure the star washers make solid electrical contact

with the metal cabinet; refer to the illustrations below.

The antenna should be mounted as high above ground level as possible while at the same time taking care not

to place the antenna under a Radio Frequency shield of any kind. I.E. do not mount the antenna directly beneath

ametal roofingoverhang. Cellularworksbest wheninan unobstructed “lineofsight” tothecellular antennasite.

WiringConnections

Donotconnectthetransformerorbatteryuntilallotherwiring,includingtheantennaconnection,hasbeencompleted

and checked. Incorrect wiring connections may cause the LINKS1000 unit to operate improperly.

“AC”PowerTerminals

Forproperoperation,theLINKS1000requiresitsowntransformer.

Donotusethecontrolpaneltransformer

to power the LINKS1000.

Do not connect the transformer or battery until all other wiring is complete. Use a

16.5 VAC transformer with a minimum 40 VA rating to supply AC power to the LINKS1000. Do not connect the

transformer to an outlet that is controlled by a switch.

UL Listed systems should employ the ATC-Frost PIN

FTC3716 transformer.

Note: All terminals are power limited except for the battery leads. All power limited wiring shall be

installed using FPL, FPLR, FPLP or permitted substitute cable.”

INSTALLATION

Inhaltsverzeichnis

Andere DSC Sender Handbücher

DSC

DSC Links2450 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung