DSE RK Series Bedienungsanleitung
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:1
DSE SRL - ITALY - WWW.DSE.EU
RK series IP cameras
ONVIF IP cameras
Installation manual
How to connect the camera How to connect to the local network
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:2
DSE SRL - ITALY - WWW.DSE.EU
Contents of the manual
The RK series camera range is a range of IP network cameras optimized for use with NVR video
recorders.In this manual we explain how to connect the camera, how to make basic adjustments
and how to configure the parameters for the connection of network.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:3
DSE SRL - ITALY - WWW.DSE.EU
Introduction
The RK series consists of IP network cameras with H264 /
H265 compression and with video resolution from 2MP
(1080P) up to 4K. These are "Naked" cameras that are
equipped with essential hardware for those who manage
the system through an NVR.
The units connect to a LAN via the RJ45 port such as a
computer or other network drive and images can be viewed on a PC
using the Internet Explorer browser.
The power supply is possible with 12VDC adapters (not supplied) or
through the same network cable thanks to the Power over Ethernet
(POE) technology supported by all the cameras in the range.
The RK Series cameras fully support the international ONVIF protocol and are compatible with
any IP recording software or multi-protocol
network video recorder (NVR) capable of handling
this standard.
DSE is one of the few Italian companies to be a
member of the Onvif association and guarantees
full compliance of its products with the most
up-to-date standard.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:4
DSE SRL - ITALY - WWW.DSE.EU
Technical data
See updated tables at:
https://www.dseitalia.it/prod_telecamere_ip_megapixel.htm
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:5
DSE SRL - ITALY - WWW.DSE.EU
Installation
CONNECTIONS
All RK series cameras have only 2 connections: a mains socket and a 12VDC power plug,
RJ45 NETWORK PORT - RJ45 FEMALE connector to connect the LAN network. To connect to
a HUB or network switch use a normal LAN cable. To connect only one PC directly, use a
crossover cable.
POE POWER - The cameras support 802.3af POE power through the network cable. To use
this form of power, you must have switches with POE ports capable of supplying power.
Alternatively, external POE injectors can be used. If the POE power supply is used, the 12VDC
plug opposite must not be used.
12VDC - Plug to connect the 220VAC / 12VDC power supply (not included) if you do not want
to power the camera in POE through the network cable. Connect a 12VDC power supply of at
least 1A.
All RK cameras can be used outdoors and for this reason they have a waterproof and gasketed
watertight network connector that must be assembled as shown in the figure. Note that the
watertight connector is present as an additional protection, but it is always advisable to protect
the connections from the elements inside junction boxes or by purchasing the appropriate
watertight boxes for connections to be installed between the camera and the wall.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:6
DSE SRL - ITALY - WWW.DSE.EU
CONNECTION AND CHECK NETWORK CONNECTION
Connect ONLY ONE CAMERA AT A TIME to the network, as having the same fixed base address
would conflict. Only after configuring the IP address of the first camera will it be possible to
connect another one.
After connecting the network cable, it is a good idea to check that the LEDs on the switch near the
network port are flashing, to confirm a good data connection is in progress.
MANUAL LENS ADJUSTMENT
The smaller models in this range are equipped with a fixed,
non-adjustable lens. In these models the lens is factory
adjusted and does not need to be focused.
The larger models, with IR over 20 m., Are equipped with
an adjustable lens. In these models there are 2 external
adjustment screws. It is necessary to operate, with the
supplied wrench, first on the ZOOM screw to adjust the angle of view and then on the FOCUS
screw to finely adjust the focus. These adjustments must be made by observing the image on
the screen. Take the time to get the perfect fit as this will have a crucial effect on the
effectiveness of the system.
MOTORIZED ZOOM LENS ADJUSTMENT
The models with motorized lens (Ref. ---- Z) allow you to
adjust the zoom by acting directly via the network by
connecting with the Internet Explorer browser or our APP,
or via the NVR. You operate the PTZ CONTROLS to set the
desired zoom. The focus is automatic.
ASSEMBLY OF CYLINDRICAL CAMERAS
The cylindrical cameras are equipped with an integrated
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:7
DSE SRL - ITALY - WWW.DSE.EU
bracket for wall mounting, specially made to allow the passage of cables inside it and protect
them from tampering attempts. The camera is usually mounted at the cable outlet so that no
cables are left bare. However, the fixing base also has a lateral cable outlet slot if the cables come
from the side in an external conduit.
The bracket must be fixed to the wall or ceiling with the supplied plugs. On the back of the way
bracket is an insulating foam pad whose function is to eliminate the space for the penetration of
insects.
With the Allen key supplied, loosen the retaining screw B and then orient the camera thanks to
the joint A. At the end, fully tighten the retaining screw B to lock the camera in its position
ASSEMBLY OF SPHERICAL CAMERAS
The spherical cameras consist of the camera globe and the fixing
base which are screwed together. Before proceeding with the
assembly, the fixing base must be unscrewed, separating it from
the camera body. In general, no tools are needed to unscrew the
fixing base from the camera body, however if this is tightened too
deeply, it is possible to help.placing a rigid rod, such as a
screwdriver, between the two lateral cable outlet slots located in
the base.
The fixing base, separated from the camera, is fixed to the wall or
to the wall with plugs in correspondence with the cable outlet hole and then the camera body is
screwed onto it. Before tightening fully, orient the viewing angle correctly.
CONNECTION BOXES
For both cylindrical and spherical models, watertight boxes are available separately to house the
connections, to be mounted between the wall and the bracket. The boxes have a rear or side
cable entry (watertight cable gland included) and have the fixing holes for the different models on
the cover.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:8
DSE SRL - ITALY - WWW.DSE.EU
AVOID OBJECTS NEAR THE CAMERA
When positioning the camera, it is necessary to prevent nearby objects from entering the
shooting field, for example edges, leaves etc. because at night they would be strongly illuminated
by the IR illuminator causing a strong darkening of the image. For the same reason, the wall near
the camera should not fit into the frame.
Orient the camera so that it has a nice open view in front of you.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:9
DSE SRL - ITALY - WWW.DSE.EU
Network configuration
After supplying power to the camera via a 12VDC power supply or via POE and after
connecting the network, it is necessary to configure the network parameters in order to make
the cameras accessible from a computer. The cameras are supplied with a fixed factory
address 192.168.1.168
IPCSEARCH SOFTWARE
The IPCSearch software is included in the CD supplied with the camera and can be installed
on any PC on the network. The function of this software is to detect the presence of the
camera on the network, whatever its address, and allow you to change the camera address
to be consistent with your network. In fact, remember that for the camera to be visible to the
other PCs on the network, the first 3 parts of the IP address must be the same as the other
PCs on the network and the subnet mask must also be the same. It is advisable to connect
one camera to the network at a time and insert new ones only after having configured the
previous ones.
PRELIMINARY CHECKS
Before proceeding, you need to get some information from your network administrator
about the IP address management used in your network. It is necessary to know an IP
address that can be assigned to the camera that is not the same as any other device already
present on the network. If you are unsure about how your network works, you can use some
commands in the DOS PROMPT.
On a network PC, launch a DOS window available in the windows accessory programs.
Type IPCONFIG at the command prompt and press ENTER. The TCP / IP parameters will
appear. The second line is the IP address assigned to your computer.
INSTALLATION MANUAL
RK SERIES - IP NETWORK CAMERAS
Page:10
DSE SRL - ITALY - WWW.DSE.EU
In the example above, the address of the PC you are working on is 192.168.2.3 and the
subnet mask used is the classic 255.255.255.0. You can therefore assign an address of your
choice to the camera, such as 192.168.2.XXX, where XXX stands for a number between 0
and 255.
It is important to choose an address that is not already used by other network equipment.
To verify that the chosen address is free, try to perform a PING from the same DOS window
by typing PING followed by a space and the IP you wish to assign to the camera. If there is
no device corresponding to that address, you will receive 4 REQUEST TIME OUT as in the
following example:
All cameras support automatic IP address assignment by a DHCP server. However, this mode
is not recommended as in case of network failure or equipment restart it is possible that the
cameras change IP address making it necessary to reconfigure the NVR.
Andere Handbücher für RK Series
8
Inhaltsverzeichnis
Andere DSE IP-Kamera Handbücher
DSE
DSE RY-BCC8 Bedienungsanleitung
DSE
DSE RJ Series Bedienungsanleitung
DSE
DSE RA-N1250 Bedienungsanleitung
DSE
DSE RK Series Bedienungsanleitung
DSE
DSE RK Series Bedienungsanleitung
DSE
DSE RH Series Kurzanleitung
DSE
DSE RH Series Kurzanleitung
DSE
DSE RH Series Bedienungsanleitung
DSE
DSE RT Series Bedienungsanleitung
