DTS XR8 SPOT Bedienungsanleitung

Made in Italy

User’s Manual Rel 1.2

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

Z60Z60

XR8 SPOT

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S.

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione

dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

ARC 1200

XR 8 SPOT

ARC 1200

XR 8 SPOT

INDEX:

1- TECHNICAL FEATURES 4

2- IMPORTANT SAFETY INFORMATION 5

2.1 Fire prevention

2.2 Prevention of electric shock

2.3 Protection against ultraviolet radiation

2.4 Safety

2.5 Level of protection against the penetration of solid and liquid matter

3- MOUNTING THE LAMP 6

3.1 Lamp alignment

4- VOLTAGE AND FREQUENCY 7

5- INSTALLATION 7

5.1 Safety cable

5.2 Protection against liquids

5.3 Movement

5.4 Risk of fire

5.5 Forced ventilation

5.6 Ambient temperature

6- MAINS CONNECTION 8

6.1 Protection

7- DMX SIGNAL CONNECTION 9

7.1 DMX Addresses

7.2 Selecting the DMX address

8- DISPLAY FUNCTIONS 11

9- AUTOMATIC MODE 14

9.1 Game P

9.2 Rec Mode

10- PAN & TILT SPEED 15

11- FANS SPEED

12- ERROR MESSAGES

13- HIDDEN MENU 16

14- OPENING UP THE PROJECTOR HOUSING 17

15- REPLACING GOBOS

16- PERIODIC CLEANING 18

16.1 Lenses and reflectors

16.2 Fans and air passages

17- PERIODIC CONTROLS

18- DMX PROTOCOLS 19

19- GOBO WHEEL 30

20-COLOUR WHEEL 31

21- MOTORS CONTROL CARD 32

22- PAN & TILT CARD 33

23-CABLES RESEND CARD

24-DISPLAY CARD

25- LAMP ON-OFF CONTROL CARD

26- WIRING DIAGRAM 34

ARC 1200

XR 8 SPOT

1- TECHNICAL FEATURES

The XR 8 Spot is fitted with a Philips MSR 575/2 discharge lamp

(GX9,5 lampholder base), with a colour temperature of 7,200 °K and a luminous flux of

49,000 Lumens.

Duration is 750 hours, with replacement recommended before 1000 hours

Other recommended lamps: Philips 575 MSD (6.000K°-49.000 Lumens-3.000 hours)

The unit incorporates:

Motorized Focus system

Zoom (3 selectable beam aperture angles 11° / 15° / 18° with auto-focus)

Dimmer (emitted light is controlled by progressive and linear dimming).

Shutter (instantaneous shutter opening/closure)

Strobe: mechanical strobe effect (frequency variable from 0.85 flashes/sec to 10

flashes/sec).

Gobo wheel (7 indexable 16 bit gobos + open)

Colour wheel (8 colours + open)

Prism (indexable 3 facet prism rotating in both directions)

Frost Filter

Electronic or magnetic ballast

Pan: 540° in 3.9 seconds (8 or 16 bit) with auto repositioning system

Tilt: 320° in 2.6 seconds (8 or 16 bit) with auto repositioning system

USITT Standard DMX 512 input

20 DMX channels

4 -eight digit- LED display with 4 buttons

2 XLR connectors (In and Out) with 3 and 5 pins selectable by user

Power supply

Electronic ballast:

Universal power supply 90 - 245 V (50/60 Hz)

Electromagnetic ballast:

230 V 50-60 Hz(Standard)

On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz

Power consumption: 750 W.

Remote Lamp on/off via DMX

Operating ambient temperature -10° / 40°

Weight

26 Kg (XR8 SPOT E.B.)

Dimensions (HxDxL)

Projector (670x450x470)

Weight 26 Kg

Packing Dimensions

(HxDxL)

800 x 550 x 440 mm

Weight

33.3 Kg

ARC 1200

XR 8 SPOT

2- IMPORTANT SAFETY INFORMATION

2.1 Fire prevention:

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 MT.

-Minimum distance from the closest illuminable surface: 2 MT.

-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if

there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves

touching the inside of the moving head, including lamp replacement.

-The level of technology present in the XR8 requires the assistance of specialised personnel for all

servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective

shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are capable of

supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main

fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at

least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should

not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid matter:

-The projector is classified as an ordinary appliance and its protection level against the penetration of

solid and liquid matter is IP 20.

XR8 uses a Philips 575 MSR/2 or MSD

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, remove the 3 screws A,B, C, (photo 1) which fix the lamp holder.

2) Remove the lamp holder assembly (photo2).

3)Insert the lamp (photo 3).

The lamp used on XR 8 is made in quartz glass and should be handled with care. Always follow the

instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided

in the lamp's packaging. The GX9,5 lamp socket is symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat

the procedure.

4) Replace the lamp assembly and tighten the screws A,B,C, which were previously removed (photo4).

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic

filters and other components inside the unit.

Alignment is carried out using the 3 adjusters X, Y and Z.

During this operation you must have a uniform luminosity all around the projected area.

Philips 575 MSR/2

Power 575W

Luminous flux 49,000 lm

Colour temperature 7.200°K

Lampbase GX9,5

Rated life 1,000 hours

Photo 2Photo 1 Photo 4Photo 3

Philips 575 MSD

Power 575W

Luminous flux 43,000 lm

Colour temperature 6.000°K

Lampbase GX9,5

Rated life 3,000 hours

Photo 5

XR 8 SPOT

4- VOLTAGE AND FREQUENCY

The XR8 with electronic ballast can operate at 90-245 VOLT 50 or 60 Hz.

The XR8 with electromagnetic ballast can operate at

5- INSTALLATION

XR8 may be either floor or ceiling mounted.

For floor mounting installations, the XR8 is supplied with four rubber mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the

mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the

unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to

move or shake whilst the XR8 is moving.

Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps

provided in the box, to fix the unit in any position.

5.1- Safety cable

We recommend the use of a safety cable or chain connected to the XR8 and to the suspension truss in

order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron

cable or chain can bear the weight of the entire unit.

You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the

picture below.

5.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come

into contact with oil, water or any other liquid. The proper unit functioning would be compromised

should this occur.

230 V 50-60 Hz(Standard)

On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz

XR 8 SPOT

5.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any

obstructions in the path of the projector's movement.

5.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended

distance from flammable material is 1 MT.

Minimum distance from the object being illuminated is 2 MT.

5.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the

base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the

projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

5.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature

should NOT exceed 40°C.

6- MAINS CONNECTION

XR8 with electronic ballast operate at 90-245 VOLT 50-60 Hz.

XR8 with electromagnetic ballast operate at 230 VOLT 50-60 Hz

Prior to connecting the unit to your mains supply,

ensure that the model in your possession correctly matches

the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 6,3 amps at 208-230V,

Or16 amps at 100-120 V

Strict adherence to regulatory norms is strongly recommended.

6.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR 8.

A good earth connection is essential for the correct operation of the projector.

7- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the

projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a

CANNON XLR 5 or 3 pins connector.

(On request: 100 V 50-60 Hz /120 V 60 HZ / 208 V 60 Hz)

540°

270°

XR 8 SPOT

Electronic ballast

90-245V 50 / 60Hz

Electromagnetic ballast

230 V 50/60 Hz (standard)

On request: 100 V 50-60 Hz

120 V 60 HZ / 208 V 60 Hz

Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it

to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the

second one.

In this way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

The standard configuration of the XR8 is with XLR 5 pins connection.

To convert to an XLR 3 pins configuration proceed as follows:

1) Remove the 2 screws fixing the display cover panel to the unit (photo 1).

2) Remove the screws that fix the XLR connectors to the panel (photo 2).

3) Rotate the electronic card by 180° (photo 3).

4) Place the 3 pins XLR connectors in the special holes and close.

For Installations where long distance DMX cable connections are needed,we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

Photo 2Photo 1 Photo 3

4 2

11=GND

2=DATA-

3=DATA+

CONTROLLER

S TA N D A R D

DM X 5 1 2

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

XR 8 SPOT

7.1-DMX Addresses

XR8 can be used in two different modes: 16 or 20 DMX (default) channels.

If you want to use the XR8 in 16 channels mode, select the 16 CH mode from the MODE menu and set

the following addresses on the mixer:

Projector 1 A001

Projector 2 A017 If you want to select the next projector, just add “16”

Projector 3 A033

….. A….

projector 6 A081

If you want to use the XR8 in 20 channels mode, select the 20 CH mode from the MODE menu and set

the following addresses:

Projector 1 A001

Projector 2 A021 If you want to select the next projector, just add “20”

Projector 3 A041

….. A….

Projector 6 A101

7.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will

start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a

faster selection.

XR 8 SPOT

Andere Handbücher für XR8 SPOT

Inhaltsverzeichnis

Andere DTS Leuchte Handbücher

DTS

DTS DELTA 12 HEAD Bedienungsanleitung

DTS

DTS NICK NRG 501 Bedienungsanleitung

DTS

DTS XR 8 Wash Bedienungsanleitung

DTS

DTS DIVE 6 Bedienungsanleitung

DTS

DTS MOVIELIGHT Bedienungsanleitung

DTS

DTS XR-LASER GREEN Bedienungsanleitung

DTS

DTS XR8 WASH Bedienungsanleitung

DTS

DTS VICE R Bedienungsanleitung

DTS

DTS SCENA LED 200 MZ FC Bedienungsanleitung

DTS

DTS XR9 Spot Bedienungsanleitung

DTS

DTS ALCHEMY 3 Bedienungsanleitung

DTS

DTS XR300 BEAM Bedienungsanleitung

DTS

DTS XR4 SPOT Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung