DTS Discharge Lamp 35-70-150W Bedienungsanleitung

Made in Italy

User’s Manual Rel 1.1

D.T.S. Illuminazione srl - ITALY

http://www.dts-lighting.it

PROFILO COMPACT

Z 20° - 40°

PROFILO COMPACT

Z 20° - 40°

Discharge Lamp 35-70-150W

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti

i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della DTS .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche ,

funzionali o di design a ciascun proprio prodotto. DTS non assume alcuna responsabilità

sull'uso o sull'applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked.

However, no responsibility will be taken for any errors. All rights are reserved and this

document cannot be copied, photocopied or reproduced, in part or completely, without

prior written consent from DTS.DTS reserves the right to make any aesthetic, functional

or design modifications to any of its products without prior notice. DTS assumes no

responsibility for the use or application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec

le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles

reproduit, dans sa totalité ou partiellement, sans le consentement préalable de DTS.

DTS se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. DTS décline toute

responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales

inexactitudes. Todos los derechos han sido reservados y este documento no puede ser

copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorizaciónescrita

de DTS.DTS se reserva el derecho a aportar sin previo aviso cambios y modificaciones

de carácter estético, funcional o de diseño a cada producto suyo. DTS no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

PROFILO COMPACT

MADE IN ITALY

INDEX

Technical features pag 4

Important Safety informations pag 6

Mounting the lamp pag 7

Voltage and frequency pag 8

Installation pag 8

Mains connection pag 8

Projector use pag 9

Opening the projector housing pag 10

Periodic cleaning pag 11

Periodic controls pag 11

PROFILO COMPACT

4 PROFILO COMPACT

1 TECHNICAL FEATURES

PROFILO COMPACT is a new range of small and lightweight shapers, ideal for use in theatres,

showrooms, shops, museums, churches, trade fairs, conferences, etc.

PROFILO COMPACT models offer an elegant and compact design and a choice of different

finishes for easy installation even in the most refined settings.

PROFILO COMPACT has an internal system with four shutters to give high-precision shaping of

light beams.

PROFILO COMPACT also offers a series of high-level operating features neatly fitted into an

extremely small space.

PROFILO COMPACT is available in 2 versions: with halogen lamp (max 300W), or discharge lamp

(150W / 70W / 35W) with built-in ballast.

PROFILO COMPACT 35W (Cod. 03.TP006)

35W discharge lamp • Black colour

PROFILO COMPACT 70W (Cod. 03.TP004)

70W discharge lamp • Black colour

PROFILO COMPACT 150W (Cod. 03.TP003)

150W discharge lamp • Black colour

PROFILO COMPACT HALO 300W (Cod. 03.TS004.F)

300W halogen lamp • Black colour

Construction

Extremely compact and lightweight

Steel housing with aluminium edge profiles

Front-box for filter frame and barn door with locking system

Gobo holder for image projection (optional)

Internal ventilation labyrinth

Removable cover for easy access to lamp

Reversible yoke for using the projector in any position

Finishings

Black, White (RAL 9003), Grey (RAL 9006) or other colours on demand

Safety

Frontal protection grille (removable)

Heat insulated knobs and handles

Optical unit

High definition zoom lens with double optical condenser lens

Optical tempered glass lenses with anti-reflective coating

Focal adjustment from 20° to 40°, giving precision movement on a double track

Spherical reflector in polished and treated 99.9% aluminium

Internal system with four removable shutters

Iris

Iris diaphragm

Lampholders

G12 lampholder for discharge lamps (150W / 70W / 35W)

GY9,5 lampholder for halogen lamps (max 300W)

Power supply

230V 50/60Hz

Built-in ballast 230V 50/60Hz (discharge lamp models)

PROFILO COMPACT

1 TECHNICAL FEATURES

ACCESSORIES

• Barn-door, black finishing (Cod. 03.TA206)

• Iris/diaphragm for Profilo Compact (Cod. 03.TA207)

• Gobo holder (Cod. 03.TA208)

• “C” Clamp G30 black (max. load 5Kg) (cod. 0521A020)

• “C” Clamp G30 chrome (max. load. 5Kg) (cod. 0521A020.20)

• Safety wire (3mm x 60 cm), ring spring catch (max. load 60Kg) (cod. 0521A010)

• GY9,5 M38 300W 230V halogen lamp (Cod. 0505A032)

• GY9,5 CP81 300W 230V halogen lamp (Cod. 0505A005)

• CDM-T150/832 (MCD 150W) discharge lamp (Cod. 0505S003.1)

• CDM-SA/T 150/942 discharge lamp (Cod. 0505S003)

• HSD 150W discharge lamp (Cod. 0505S003.2)

• Gel filters

PROFILO COMPACT

DISCHARGE LAMP 150W

mm 173

mm 154

mm 429

mm 388

mm 143

6 PROFILO COMPACT

2 IMPORTANT SAFETY INFORMATION

2.1 Fire prevention

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 10 CM.

-Minimum distance from the closest illuminable surface: 30 CM.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

2.2 Prevention of electric shock

-High voltage is present inside the unit. Unplug the unit prior to performing any function

which involves touching the inside, including lamp replacement.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

2.3 Protection against ultraviolet radiation

-Never turn on the lamp if the front lenses are damaged. Their respective shielding

function will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

2.4 Safety

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure

of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the

unit until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient

temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to

replace the lamp.

-Always wear suitable hand protection when handling the lamp.

2.5 Level of protection against the penetration of solid and liquid objects

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP 20.

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid. The proper unit

functioning would be compromised should this occur.

7 PROFILO COMPACT

3 MOUNTING THE LAMP

1) Loose the screw and the knob located on the top back side of the unit

(Photo 1 and 2).

2) Remove the top back cover (photo 3) and insert the lamp (photo 4).

No lamp allignment needed

The lamp used is manufactured from quartz glass and should be handled with care.

Always adhere to the instructions supplied in the lamp's packaging. Never touch the

glass directly but use the tissue provided in the lamp's packaging. The G12 lampbase is

symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, re-read the

instructions and repeat the procedure.

Photo 1 Photo 2

screw and knob

Photo 3 Photo 4

PROFILO COMPACT

4 VOLTAGE AND FREQUENCY

Profilo Compact with discharge lamp operates at 230V 50 - 60 Hz.

5 INSTALLATION

Profilo Compact may be either floor or ceiling mounted.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix

the unit to the mounting surface.

A safety cable must always be present.

6 MAINS CONNECTION

PROFILO COMPACT with discharge lamp operates at 230 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available. For connection purposes,

ensure that your plug is capable of supporting 1,5 amps at 230V,

6.1 Protection

The use of a thermal magnetic circuit breaker is recommended for each unit.

A good earth connection is essential for the correct operation of the projector.

ceiling installations Floor installations

WARNING: The rear side of the unit, can reach very high temperature.

Handle the projector with extreme caution

7 PROJECTOR USE

7.1 Focus and Zoom

7.2 Blades

Profilo Compact is provided with four indipendent steel blades.The blades let you

create geometrical figures with the light.

Focus and zoom adjustment lenses, are located on the front side of the unit.

Place the projector on the object to illuminate, loose the fixing lenses , adjust the

lenses position till the projection is whell focused on the object.

Thighten the knobs

knobs

PROFILO COMPACT

Focus and Zoom

Light beam with no blades inserted

Blade

Light beam with blades inserted

PROFILO COMPACT

7.3 Blades insertion

To insert the blades on the unit, proceed as follow:

Locate the blades holder, place one side of the blade within the two parallel surfaces,

push and tilt it on the guide.

Warning:

8 OPENING THE PROJECTOR HOUSING

8.1 Back side

It is possible to inspect the inside of the projector by removing the cover as indicated below.

Remove mains power prior to accessing the projector’s internal

components.

1) Loose the screw and the knob located on the top back side of the unit (photo 1 and 2).

2) Remove the top back side cover (photo 3)

Blades holder

7.3 Blades insertion

To insert the blades on the unit, proceed as follow:

Locate the blades holder, place one side of the blade within the two parallel surfaces,

push and tilt it on the guide.

Warning:

8 OPENING THE PROJECTOR HOUSING

8.1 Back side

It is possible to inspect the inside of the projector by removing the cover as indicated below.

Remove mains power prior to accessing the projector’s internal

components.

1) Loose the screw and the knob located on the top back side of the unit (photo 1 and 2).

2) Remove the top back side cover (photo 3)

Parallel surfaces

screw and knob

Photo 1 Photo 2

Photo 3

Andere DTS Beleuchtungsausrüstung Handbücher

DTS

DTS SCENA LED 80 WHITE Bedienungsanleitung

DTS

DTS PROFILO LED 80 Bedienungsanleitung

DTS

DTS HORUS FULL COLOUR Bedienungsanleitung

DTS

DTS Raptor Bedienungsanleitung

DTS

DTS XR 8 Wash Bedienungsanleitung

DTS

DTS ALCHEMY 5 Bedienungsanleitung

DTS

DTS FOS 100 FULL RGBW Bedienungsanleitung

DTS

DTS Nick Wash 600 Bedienungsanleitung

DTS

DTS DELTA 12 HEAD Bedienungsanleitung

DTS

DTS PAR 20 Bedienungsanleitung

DTS

DTS NICK NRG1200 CT Bedienungsanleitung

DTS

DTS MOON 575 Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS A.R.C. Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Bedienungsanleitung

DTS

DTS DELTA 8 Series Bedienungsanleitung

DTS

DTS FOS 100 WHITE 36 Bedienungsanleitung

DTS

DTS Scena LED 150 Bedienungsanleitung

DTS

DTS ALCHEMY 5 Bedienungsanleitung

DTS

DTS TITAN SOLO Bedienungsanleitung

DTS

DTS DONUT 6 Bedienungsanleitung

DTS

DTS XR1200 WASH Fresnel Bedienungsanleitung

DTS

DTS ARTEMIO FRESNEL Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

LCG

LCG Thunder 400 Bedienungsanleitung