DTS SCENA COMPACT LED 50 Bedienungsanleitung

Made in Italy

PROFILO COMPACT LED 50

User’s Manual rel. 1.0 GB

D.T.S. Illuminazione s.r.l. –ITALY

http://www.dts-lighting.it/

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 4

3- GENERAL WARRANTY CONDITION 4

4- TECHNICAL FEATURES 5

5- ACCESSORIES 6

6- IMPORTANT SAFETY INFORMATION 7

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Safety

7- INPUT / OUTPUT CONNECTIONS 7

8- DMX SIGNAL CONNECTION 8

8.1 DMX Addresses

8.2 Selecting the DMX address

9- FIRMWARE UPDATING 9

10- DISPLAY FUNCTIONS 10

11- DMX PROTOCOL 14

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE

UNIT ON NORMALLY FLAMMABLE SURFACES

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE DEVICE

AND THE LIT OBJECT

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

LED 30 cm

4- TECHNICAL FEATURES

OVERVIEW

PROFILO COMPACT LED 50 is a professional shaper featuring a single high-power

White LED (4,725 Lux / 2 m, 3.000K), and 18°- 36° linear zoom with high-efficiency

optical system.

PROFILO COMPACT LED 50 features an internal rotating system with four

removable shutters, to give high-precision shaping of light beams.

PROFILO COMPACT LED 50 is a modern alternative to conventional lights,

improving light quality, flexibility of use and installation, energy savings and

component duration.

In fact the fixture doesn’t heat up, and the projection is always flicker free.

Also, the dimming curves are similar to those of halogen lamps.

PROFILO COMPACT LED 50 is contained in a strong housing with folded edges,

designed to resist all the rigors of continuous use.

PROFILO COMPACT LED 50 features a reversible yoke for using the projector in any

position. Also, the yoke has an exclusive round flange + clutch system which

guarantees a perfect grip and safer operation.

PRODUCT CODES:

03.TP015.46 PROFILO COMPACT LED 50 *White 3.000°K *Black

03.TP016.46 PROFILO COMPACT LED 50 *White 4.000°K *Black

03.TP017.46 PROFILO COMPACT LED 50 *White 5.000°K *Black

LED Technology

1 x White LED (3.000 °K, 4000°K or 5000°K)

CRI > 90; LED Max power: 50W

Optical group

18°-36° linear zoom; 2100 Lux / 3 m (18°)

Shutters

4 removable shutters

Control

2 DMX channels

4 digit 7 segments display + 4 soft keys

Connectors

Power supply: POWERCON IN & OUT connectors

DMX: 5 poles In & Out connectors

Power supply

Electronic full-range AC 90-260V , 50/60 Hz

Weight

4,9 Kg

DIMENSIONS

5- ACCESSORIES

As standard

1 x User’s Manual

1 x POWERCON male cable connector (D.T.S. Code 0520P014)

1 x XLR 5 pins male cable connector (D.T.S. Code 0508B028)

1 x XLR 5 pins female cable connector (D.T.S. Code 0508B027)

4 x Shutter blades (Single blade D.T.S. Code 02SK0041)

Optional (on request)

- “C” Clamp G60 (Max. Load. 50 Kg) *Black finish (D.T.S. Code 0521A004)

- Gobo holder (D.T.S. Code 03.TA208)

- Iris/diaphram (D.T.S. Code 03.TA207)

- Barndoor *Black finish (D.T.S. Code 03.TA206)

- Filterframe *Black finish (D.T.S. Code 02M00422.46)

7- IMPORTANT SAFETY INFORMATION

7.1 Fire prevention:

It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

Minimum distance from the closest illuminable surface: 30 cm.

Replace any blown or damaged fuses only with those of identical value (1AT).

7.2 Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of

the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

The use of a thermal magnetic circuit breaker is recommended for each PROFILO

COMPACT LED 50 unit. Use only AC supplies 90-260V , 50 / 60 Hz.

PROFILO COMPACT LED 50 should never be located in position exposed to rain or in

areas of extreme humidity.

A good air ventilation is essential for proper equipment work.

7.3 Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at least 5

minutes have elapsed since the unit was turned off.

Never install the unit in an enclosed area lacking sufficient air flow.

The ambient temperature should not exeed 40°C and should not be lower than -10°C.

8- INPUT / OUTPUT CONNECTIONS

FUSE 1AT

DMX OUT

XLR 5 Pins Male Panel Connector

MAINS AC INPUT 90-260V , 50/60 Hz

DMX IN

XLR 5 Pins Female Panel Connector

DISPLAY PANEL

MAINS AC OUTPUT 90-260V , 50/60 Hz

MAX 16A

9- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we

suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

OUT

120 ohm

PIN 3

PIN 2

4 2

11=GND

2=DATA-

3=DATA+

CONTROLLER

S T A N D A R D

D M X 5 1 2

DMX OUT DMX OUT

DMX IN DMX IN

DMX OUT

DMX IN

DMX OUT

9.1 DMX addresses

PROFILO COMPACT LED 50 can be controlled with 2 DMX channels.

In order to use the unit in 2 DMX channels mode, set the following addresses on the

mixer:

Projector 1 A001

Projector 2 A003 If you want to select the next projector, just add “2”

Projector 3 A005

….. A….

projector 6 A011

9.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

10- FIRMWARE UPDATING

To update the software version of the PROFILO COMPACT LED 50 you need:

- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)

- USB-DMX Driver for the D.T.S. RED BOX interface

- “D.T.S. Firmware upgrade utility” program installed on PC

- Latest firmware release available for PROFILO COMPACT LED 50 unit

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Send the new software version into the unit by using “D.T.S. Firmware upgrade

Utility”program.

Up-Down

MENU ENTERUp-Down Up-DownENTER

Up-DownENTER

ENTER

Up-Down

MENU ENTER

Up-Down ENTER

ENTER

Up-Down ENTER

ENTER

10- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The PROFILO COMPACT LED 50 display panel shows all the available functions.

Using these functions, it is possible to change some of the parameters and add some

functions. Changing the D.T.S. setting can vary the functions of the unit so that it does

not respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

Software version 1.00

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position (on the ground or

suspended).

DISPLAY STAND BY

To turn off the display (after 5 seconds)

Or leave it always on.

DMX MODE

To select DMX mode : 2 DMX channels

mode (default), 1 DMX channel mode,

3 DMX channels mode or Manual mode.

Manual mode can also be activated by

pressing at the same time the “UP’’ +

”DOWN” buttons on unit display for 3

seconds (“A001”).

Suspended

Position

Floor

Position

Display

Off

Display

Always on

Default DMX Mode

2 Channels

Manual Mode

1 DMX channel mode

3 DMX channels mode

Andere Handbücher für SCENA COMPACT LED 50

Inhaltsverzeichnis

Andere DTS Beleuchtungsausrüstung Handbücher

DTS

DTS DELTA 12 HEAD Bedienungsanleitung

DTS

DTS FOS 100 SOLO FULL RGBW Bedienungsanleitung

DTS

DTS Scena LED 150 Bedienungsanleitung

DTS

DTS MOON 1200 Bedienungsanleitung

DTS

DTS JACK Bedienungsanleitung

DTS

DTS HORUS FULL COLOUR Bedienungsanleitung

DTS

DTS XM 2500 Sport Bedienungsanleitung

DTS

DTS PROFILO LED 80 Bedienungsanleitung

DTS

DTS DELTA 8 Series Bedienungsanleitung

DTS

DTS DELTA R FULL COLOR Bedienungsanleitung

DTS

DTS XR 8 Wash Bedienungsanleitung

DTS

DTS Thomas & Betts NT 06 Handbuch

DTS

DTS SCENA COMPACT LED 50 Bedienungsanleitung

DTS

DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK Bedienungsanleitung

DTS

DTS XR5 SPOT Bedienungsanleitung

DTS

DTS Nick Wash 600 Bedienungsanleitung

DTS

DTS PROFILO 500 Bedienungsanleitung

DTS

DTS XR1200 WASH Fresnel Bedienungsanleitung

DTS

DTS Raptor Bedienungsanleitung

DTS

DTS TITAN SOLO Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

DTS

DTS NICK NRG 1201 Bedienungsanleitung

DTS

DTS Alchemy 7 Bedienungsanleitung

DTS

DTS A.R.C. Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung