DTS XR5 SPOT Bedienungsanleitung
GB
Made in Italy
XR5 SPOT
User’s Manual Rel 1.1
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
2XR 5 SPOT
3
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 5
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid objects
3- MOUNTING THE LAMP 6
3.1 Lamp alignment
4- VOLTAGE AND FREQUENCY 7
5- INSTALLATION 7
5.1 Safety cable
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION 8
6.1 Protection
7- DMX SIGNAL CONNECTION 9
7.1 DMX Addresses
7.2 Selecting the DMX address
8- DISPLAY FUNCTIONS 11
9- PAN & TILT SPEED 14
10- FANS SPEED
11- ERROR MESSAGES 15
12- HIDDEN MENU 16
13- OPENING THE PROJECTOR HOUSING 17
14- REPLACING GOBOS
15- PERIODIC CLEANING 18
15.1 Lenses and reflectors
15.2 Fans and air passages
16- PERIODIC CONTROLS
17- DMX PROTOCOL 19
18- 8 MOTORS CONTROL CARD 31
19- PAN & TILT CARD 32
20- CABLES RESEND CARD
21- DISPLAY CARD
22- LAMP ON-OFF CONTROL CARD
23- WIRING DIAGRAM 33
24- ROTATING GOBO WHEEL 34
25- FIXED GOBO WHEEL 35
26- COLOUR WHEEL 36
XR 5 SPOT
4
1- TECHNICAL FEATURES
The XR5 Spot is fitted with a Philips MSD 250/2 discharge lamp
(GY9,5 lampholder base), with a colour temperature of 8500 °K and a luminous flux of
18,000 Lumens.
Average lifespan is 3000 hours, with replacement recommended before 3200 hours
Other recommended lamps: Osram HSD 250/2, GE CSD 250/2.
The unit incorporates:
Dichroic parabolic reflector
Motorized Focus system
Dimmer (emitted light is controlled by progressive and linear dimming).
Shutter (instantaneous shutter opening/closure).
Strobe: mechanical strobe effect (frequency variable from 0.85 flashes/sec to 10
flashes/sec).
Motorized iris.
2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (11 gobos)
1 Colour wheels (8 colours ).
Prism (indexable 3 facet prism rotating in both directions).
Electromagnetic ballast.
Pan: 540° in 2.8 seconds (8 or 16 bit) with auto repositioning system.
Tilt: 270° in 2.0 seconds (8 or 16 bit) with auto repositioning system.
USITT Standard DMX 512 input signal.
15 or 21 DMX channels.
4 -eight digit- LED display with 4 buttons.
Power supply
Electromagnetic ballast: 230 V (50/60 Hz) standard.
On request: 100 V (50/60 Hz) or 120 V (60 Hz).
Power consumption: 350 W
Remote Lamp on/off via DMX
Operating ambient temperature: -10° / 40°C
Weight: 20 Kg
4 XLR connectors (In and Out) with 3 and 5 pins.
Dimensions (LxWxH)
projector (432x415x590mm)
Packaging Dimensions
(LxWxH)
550 x 440 x 800 mm
Weight
27 Kg
XR 5 SPOT
m590 m
270°
15 mm
4408 mm
363 mm
m
550 m
32 mm
4
5
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology inherent in the XR5 requires the assistance of specialised personnel for all
servicing.Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 20.
XR5 Spot can fit a Philips MSD250/2, a Osram HSD250/2 or a GE CSD250/2.
XR 5 SPOT
3- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
1) Using a screwdriver, remove the 3 screws X, Y, Z, (photo 1) which fix the lamp holder.
2) Remove the lamp holder assembly and insert the lamp (photo 2).
The lamp used on XR5 Spot is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The GY9,5 lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
3) Replace the lamp assembly and tighten the screws X, Y and Z, which were previously removed
(photo 3).
3.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.
using the 3 adjusters A, B and C (photo 4)
Philips MSD250/2
Power 250W
Luminous flux 18.000 lm
Colour temperature 8.500°K
Lampbase GY9,5
Rated life 3,000 hours
Apply power and allow the XR5 Spot to reset.
Using either a controller or the control menu (LAMP / ADJUST), strike the lamp and project an open
white beam on a flat surface.
Center the hot spot until the light is bright and evenly
distributed.
6XR 5 SPOT
Photo 2Photo 1 Photo 3
Photo 4
4- VOLTAGE AND FREQUENCY
The XR5 Spot with electromagnetic ballast can operate at 230 VOLT 50-60 Hz.
5- INSTALLATION
XR5 Spot may be either floor or ceiling mounted.
For floor mounting installations, the XR5 Spot is supplied with four rubber mounting feet under the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR5 is moving.
Four quarter turn fast locks placed on the base, allow to fix the unit in any position, by using the two fast
lock C clamps provided in the box.
5.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR5 Spot and to the suspension
truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the
iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.
5.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
On request 100 V (50/60 Hz) or 120 V (60 Hz).
7
A
XR 5 SPOT
5.3- Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
5.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.
5.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
5.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
6- MAINS CONNECTION
XR5 Spot with electromagnetic ballast operates at 230 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 3,15 amps at 230V,
Strict adherence to regulatory norms is strongly recommended.
6.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR5 Spot.
A good earth connection is essential for the correct operation of the projector.
8
540°
270°
XR 5 SPOT
Electromagnetic ballast
230V 50 / 60Hz
7- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.
Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
This way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed, we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
3
4 2
11=GND
2=DATA-
3=DATA+
CONTROLLER
S T A N D A R D
DM X 5 1 2
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
9XR 5 SPOT
7.1-DMX Addresses
XR5 Spot can be used in two different modes: 15 or 21 DMX (default) channels.
If you want to use the XR5 Spot in 15 channels mode, select the 15 CH mode from the MODE menu and
set the following addresses on the mixer:
Projector 1 A001
Projector 2 A016 If you want to select the next projector, just add “15”
Projector 3 A031
….. A….
projector 6 A076
If you want to use the XR5 Spot in 21 channels mode, select the 21 CH mode from the MODE menu and
set the following addresses:
Projector 1 A001
Projector 2 A022 If you want to select the next projector, just add “21”
Projector 3 A043
….. A….
Projector 6 A106
7.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now set to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
10 XR 5 SPOT
Andere DTS Beleuchtungsausrüstung Handbücher
DTS
DTS XM 1200 SPOT Bedienungsanleitung
DTS
DTS PAR64Ip66 watertight Bedienungsanleitung
DTS
DTS DELTA 8 Series Bedienungsanleitung
DTS
DTS PROFILO 500 Bedienungsanleitung
DTS
DTS NicKWash 600 Bedienungsanleitung
DTS
DTS Scena LED 150 Bedienungsanleitung
DTS
DTS Discharge Lamp 35-70-150W Bedienungsanleitung
DTS
DTS Alchemy 7 Bedienungsanleitung
DTS
DTS NICK NRG 1201 Bedienungsanleitung
DTS
DTS PAR 20 Bedienungsanleitung
DTS
DTS DELTA 10 F Bedienungsanleitung
DTS
DTS A.R.C. Bedienungsanleitung
DTS
DTS MOON 1200 Bedienungsanleitung
DTS
DTS PROFILO LED 80 Bedienungsanleitung
DTS
DTS DELTA 12 HEAD Bedienungsanleitung
DTS
DTS XR1200 WASH Fresnel Bedienungsanleitung
DTS
DTS FOS 100 SOLO FULL RGBW Bedienungsanleitung
DTS
DTS FOS 100 FULL RGBW Bedienungsanleitung
DTS
DTS DONUT 6 Bedienungsanleitung
DTS
DTS Thomas & Betts NT 06 Handbuch
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
