Dual MXD135BT Betriebsanleitung

INSTALLATION/OWNER'S MANUAL

AM/FM Marine Receiver with Detachable Face

MXD135BT

MXD135BT INSTALLATION

TYPICAL FRONT-LOAD

DIN MOUNTING METHOD

Preparation

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.

• Avoid installing the unit where it would be subject to high temperatures, such as from

direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove trim ring from unit.

• Remove 2 transit screws located on top of the unit.

• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting

sleeve.

• Install mounting sleeve into opening, bending tabs to secure.

• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.

• Certain vehicles may require an installation kit and/or wiring

harness adapter (sold separately).

• Test for correct operation and slide into mounting sleeve to secure.

• Snap trim ring into place.

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

MXD135BT INSTALLATION

Wiring Diagram

FUSE

When replacing the fuse,

make sure new fuse is the

correct type and amperage.

Using an incorrect fuse could

damage the radio.

The MXD135BT uses one

10 amp AGC fuse located

in-line.

Antenna

Connector

10 AMP

AGC Fuse

MXD135BT OPERATION

Control Locations - Receiver

Preset 3 / Intro

Preset 2 / Random

Preset 1 / Repeat

Display

Tune Up

Tune Down

Mode

Audio / Menu

Bluetooth Talk

Release

Band / Go Back

Volume Knob

Power / Mute

USB Port

Auxiliary Input

Preset 6 / Folder Up

Preset 5 / Folder Down

Preset 4 / Play / Pause

1 2 3 4 5

1 10

2 11

3 12

4 13

5 14

6 15

7 16

8 17

9 18

13 12 11 10 9 8 71617 1415

MXD135BT OPERATION

Control Locations - Remote

16 6

Preset 6 / Folder Up

Mute

Audio / Menu

Preset 5 / Folder Down

Preset 4 / Play / Pause

Preset 1 / Repeat

Bluetooth Talk

Tune / Track Down

Mode

Volume Up

Power

Select

Tune / Track Up

Volume Down

Band / Go Back

Preset 3 / Intro

Preset 2 / Random

MXD135BT OPERATION

General Operation

Press RELEASE and pull away from the left side to

remove. To re-install, insert right side of faceplate first

then push left side to secure.

Press or any other button to turn the unit on. Press and

hold again to turn the unit off.

When the unit is on, press momentarily to mute the

audio. Press again to return to previously-selected

volume.

Press MODE to select between AM/FM, USB, Bluetooth or

auxiliary input modes. Modes of operation are indicated in

the display. USB mode will not appear unless a USB device

is connected.

The radio frequency (tuner mode) or MP3/WMA title/track

information (USB mode) will be shown by default. Press

DISP to display the clock. The default display will return

after five seconds.

When in USB mode, the display will alternate between

track number/elapsed time and available MP3/WMA

information, including file name, song title, artist name,

album name and folder name.

Press RESET upon initial installation or if abnormal

operation occurs. Reset button is located behind the front

panel.

Press DISP to display the clock, then press and hold DISP

until the hours will flash. Press TUNE

to adjust the

minutes and TUNE

to adjust the hours.

Insert a 3.5mm connector in the front panel AUX port.

Connect the other end of the 3.5mm connector to the

headphone output of an audio device, MP3 player, etc.

Adjust volume using the volume knob (00-40).

Faceplate Removal

Power On/Off

Mute

Mode

Display

Reset

Set the Clock

Auxiliary Input

Volume

MXD135BT OPERATION

General Operation

Press the AUDIO/MENU to select between Bass, Treble,

Balance, Fader, Loudness, Distance and Stereo.

Press AUDIO/MENU until BAS appears.

Rotate the volume knob left/right to adjust.

(-7 minimum / +7 maximum)

Press AUDIO/MENU until TRE appears.

Rotate the volume knob left/right to adjust.

(-7 minimum / +7 maximum)

Press AUDIO/MENU until BAL appears. Rotate the volume

knob left/right to adjust from 10L (left) to 10R (right). "BAL

EVEN" represents equal balance.

Press AUDIO/MENU until FAD appears. Rotate the vol-

ume knob left/right to adjust from 10R (rear) to 10F (front).

"FADER EVEN" represents equal balance.

Press AUDIO/MENU until LOUD ON or LOUD OFF appears,

then rotate the volume knob to select desired option.

Activating this feature will enhance the bass and treble fre-

quencies when listening to music at low volumes.

Press AUDIO/MENU until EQ appears, then rotate the volume

knob to select between the following preset equalization curves:

FLAT, POP, JAZZ, ROCK and OFF.

From tuner mode only, press AUDIO/MENU until STEREO

or MONO appears, then rotate the volume knob to select

desired option. Selecting MONO can improve listening in

areas with a weak FM signal.

Press and hold AUDIO/MENU for more than 3 seconds to

access the setup menu. Press AUDIO/MENU momentarily

to select between the menu functions and rotate the volume

knob left/right to adjust or activate the desired function.

Options are outlined on the following page.

Audio / Menu

Bass

Treble

Balance

Fader

Loudness

Stereo / Mono

Setup Menu

BASS TREBLE BALANCE FADER LOUDNESS EQ STEREO

MXD135BT OPERATION

General Operation - Setup Menu

Menu Function Options Action

Auto Station

Store AUTO STORE Press the volume knob to seek and save 6 strong stations in

the current band. (Tuner mode only)

Local/Distance

Tuning

LOCAL OFF Activates distance tuning (Tuner mode only).

LOCAL ON Activates local tuning for strong station reception only

(Tuner mode only).

Tuner

Frequency

Spacing

FREQ USA Programs the unit to USA tuner spacing.

(200kHz for FM and 10kHz for AM). (Tuner mode only)

FREQ EURO Programs the unit to European tuner spacing.

(50kHz for FM and 9kHz for AM). (Tuner mode only)

Subwoofer SUBWFR ON Enables the subwoofer.

SUBWFR OFF Disables the subwoofer.

Beep

Confirmation

BEEP OFF Disables the confirmation beep.

BEEP ON Enables the confirmation beep.

LED Color

LED AUTO Programs unit to automatically rotate through all LED

colors.

BLUE Programs unit to use blue LED display.

GREEN Programs unit to use green LED display.

RED Programs unit to use red LED display.

YELLOW Programs unit to use yellow LED display.

PURPLE Programs unit to use purple LED display.

CYAN Programs unit to use cyan LED display.

WHITE Programs unit to use white LED display.

LED ADJ Press and rotate the volume knob to adjust each RGB color

level. After adjustment, that color will appear on the LCD.

Bluetooth BT ON Enables Bluetooth functionality.

BT OFF Disables Bluetooth functionality.

Auto Answer

ANSWER AUTO Programs unit to automatically answer every incoming

phone call after 2-3 rings.

ANSWER MANU Programs unit to require the button to be pressed

manually to answer incoming phone calls.

MXD135BT OPERATION

Seek Tuning

Manual Tuning

Band

Storing and Recalling

Station Presets

Press and hold TUNE

or TUNE

to seek to the

next strong station.

Press TUNE

or TUNE

to change radio frequency

up or down one step at a time. Press and hold to advance

quickly.

Press BAND to select between FM1, FM2, FM3, AM1 and

AM2 bands.

Up to 18 FM stations and 12 AM stations can be stored. To

store a station, select the desired band and station. Press

and hold the desired preset button (1-6) for more than

2 seconds. When stored, the preset number will appear in

the display. The station can be recalled anytime by pressing

the corresponding preset button.

AM/FM Tuner Operation

MXD135BT OPERATION

Connecting a USB Device

(sold separately)

Playing Music

Track Select

Fast Forward and

Reverse

Pause

Displaying Information

Repeat

Random

To play MP3/WMA files from most USB mass storage

devices, line up the USB connector and insert the USB

device into the USB port.

When a USB device is first connected, “LOAD” will appear in

the display and playback will begin momentarily. Depending

on the number of files and folders, it may take several

seconds for the device to begin playing. If no valid MP3/

WMA files are detected, “NO FILE” will be displayed and the

last mode will be resumed.

Press TRACK

to skip to the beginning of the next

track. Press TRACK

to return to the beginning of the

current track. Pressing TRACK

again skips to the

beginning of the previous track.

Press and hold TRACK

or TRACK

on the remote

control to fast forward or reverse a track.

Press

to temporarily stop USB playback.

Press

again to resume playback.

ID3 tag and file/folder information will be automatically

changed during playback. Press DISP to view the clock.

Default display will resume after five seconds.

Press RPT to choose between:

• Current Song - Continuously repeats selected track.

• Current Folder - Continuously repeats all files in folder.

Press RDM to choose between:

• Off - Cancels RDM function.

• All Songs - Plays all tracks in random order.

• Current Folder - Plays all tracks in folder in random

order.

USB Operation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dual Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung