Dual XDMR7700 Betriebsanleitung

INSTALLATION/OWNER’S MANUAL

XM Ready Multimedia Receiver with Detach Face

XDMR7700

An optional XM Satellite Radio Receiver may be connected to the XDMR7700.

XM subscription is required for reception. For more information, visit XM’s website at

www.xmradio.com or call 1-877-XMRADIO. Not available in Alaska or Hawaii.

XDMR7700 INSTALLATION

Preparation

TYPICAL FRONT-LOAD DIN MOUNTING METHOD

KEYS

Please read entire manual before installation.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the unit where it would be subject to high temperatures, such as from

direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

Getting Started

• Remove 2 transit screws located

on top of the unit.

• Insert the supplied keys into the

slots as shown, and slide the unit

out of the mounting sleeve.

• Install mounting sleeve into

opening, bending tabs to secure.

• Connect wiring harness and

antenna. (consult a qualified

technician if you are unsure)

• Certain vehicles may require an

installation kit and/or wiring

harness adapter (sold separately).

• Test for correct operation and slide

into mounting sleeve to secure.

• Snap trim ring into place.

• Mount the iplug™adapter to any

smooth clean surface using the

supplied double-sided tape or

#2 x 3/8” Phillips head screws.

XDMR7700 INSTALLATION

Wiring Diagram

FUSE

When replacing the fuse,

make sure new fuse is the

correct type and amperage.

Using an incorrect fuse

could damage the radio.

The XDMR7700 uses one

10 amp ATM fuse located

beside the wiring connector.

XDMR7700 OPERATION

Control Locations - Receiver

Open

Tune/Track Down

AS/PS/Enter/Function

Mode/Search/Shift

Tune/Track Up

Audio

Volume

Display

Tuner Scan/*Preset 8

Local/Distance/*Preset 7

Loudness/*Preset 10

EQ/*Preset 9

Eject

Mute

Infrared Sensor

Preset 6/Category-Folder Up

Preset 5/Category-Folder Down

Preset 4

Preset 3/CD Intro

Preset 2/CD Random

Preset 1/CD Repeat

Band/Pause/Scroll

Power

Reset

23 22 21 20 19 18 17 16 15 14

1 2 4 789

310

5611

12 13

An optional XM Satellite Radio Receiver may be connected to the XDMR7700.

XM subscription is required for reception. For more information, visit XM’s website at

www.xmradio.com or call 1-877-XMRADIO. Not available in Alaska or Hawaii.

*Function buttons 7, 8, 9 and 0 apply to XM Radio and MP3/WMA operation only.

EQ/*Preset 9

Tuner Scan/*Preset 8

Local/Distance/*Preset 7

Preset 5/Category-Folder Down

Preset 4

Preset 1/CD Repeat

Mode/Search/Shift

Tune/Track Down

Band/Pause/Scroll

Power

Volume Up

AS/PS/Enter/Function

Audio

Tune/Track Up

Loudness/*Preset 10

Volume Down

Preset 3/CD Intro

Preset 2/CD Random

Preset 6/Category-Folder Up

XDMR7700 OPERATION

Control Locations - Remote

XDMR7700 OPERATION

General Operation

With the unit off, press OPEN to allow the front panel to slide

down. Gently squeeze the release tab located on the bottom

center underside and pull faceplate down and away from unit

to remove. To install, insert left side faceplate first, then push

right side to secure.

Before installation, remove trim ring and install supplied

Phillips head #1 x 7/32” screws through left and right

underside of faceplate tray into faceplate.

Press PWR or any other button (except EJECT or OPEN) to turn

the unit on. Inserting a CD will turn the unit on automatically.

Press PWR to turn the unit off.

Press MODE to select between AM/FM, *XM Radio, CD player

and auxiliary input. Modes of operation are indicated in the

display.

*Optional XM Satellite Radio Receiver and subscription

required for XM Radio operation.

Adjust volume using rotary encoder (00-46).

Press and hold POWER for 3 seconds to program currently

selected volume level. "P-VOL" and the current volume level

will momentarily appear in the display.

Press SHIFT for 2 seconds to activate the SHIFT function.

The SHIFT icon will appear in the display. In XM Radio mode,

the SHIFT function must be active to access the LOUDNESS

and EQ functions. Press SHIFT again for 2 seconds to cancel.

Note:

The SHIFT function only applies to XM Radio operation.

Press LOUD to activate and deactivate loudness contour curve.

Activating this feature will enhance the bass and treble

frequencies when listening to music at low volumes.

Press EQ to select between POP, JAZZ, CLASSIC, BEAT, ROCK

and OFF (default) equalization curves. Any adjustment to the

Bass or Treble settings automatically cancels the current EQ

curve.

Faceplate Removal

Semi-permanent

Faceplate Installation

Power On/Off

Mode

Volume

Programmable

Turn-On Volume

Shift Function

Loudness

Preset EQ Curves

XDMR7700 OPERATION

General Operation

When in AM/FM, CD or AUX mode:

Press DISP to select between clock and radio frequency

(tuner mode), clock and CD elapsed time/track (CD mode), or

clock and AUX (AUX mode).

When in XM Radio mode:

Press DISP to select between channel name, artist name,

song title or clock.

With the unit on, press and hold DISP until the clock begins

to flash, then release. Press TUNE

to adjust the hours

and TUNE

to adjust the minutes. Press DISP

momentarily to save the selected time.

The clock will display 12-hour AM/PM time in USA frequency

spacing mode (PM 10:00). In European frequency spacing

mode, the clock will display 24-hour time (22:00).

In AM/FM tuner mode, press and hold DISP then press

TUNE

to select function priority display. “FREQ” will

momentarily appear in the display.

Note:

"FUNC" will appear in XM, CD or AUX modes.

Radio frequency (tuner mode), XM information (XM mode),

CD elapsed time/track (CD mode) or AUX (AUX mode) will be

displayed by default.

Note:

When playing MP3/WMA files, the track number/elapsed

time, track name, directory name, title, artist, album, year or

comment will be displayed by default. Clock is accessed by

pressing DISP momentarily.

Press and hold DISP then press TUNE

to select time

display priority. “TIME” will momentarily appear in the

display. Clock will be displayed by default. Radio frequency

(tuner mode), XM information (XM mode), CD elapsed

time/track or MP3/WMA file information (CD mode) is

accessed by pressing DISP momentarily.

Display

Set the Clock

12/24-hour Clock

Programmable Display

Priority

XDMR7700 OPERATION

General Operation

Press and hold for more than 2 seconds to RESET the unit

upon initial installation or if abnormal operation occurs.

The reset button is located above the PWR button.

Press and hold AUD for 3 seconds to turn confirmation

beep on/off.

Press MUTE to silence the audio. “MUTE” will flash in the

display. Press MUTE again to cancel.

Press AUD to select between Volume (default), Bass,

Treble, Balance & Fader.

Press AUD until BAS appears then rotate encoder

left/right to adjust ( -6 minimum / +6 maximum).

Press AUD until TRE appears then rotate encoder

left/right to adjust ( -6 minimum / +6 maximum).

Press AUD until BAL appears then rotate encoder

left/right to adjust (BAL L 12-BAL 00-BAL R 12).

BAL 00 represents equal balance

Press AUD until FAD appears then rotate encoder

left/right to adjust (FAD F 12-FAD 00-FAD R 12).

FAD 00 represents equal fader

Individual Bass and Treble settings are retained in memory

for AM, FM, XM, CD, and AUX modes. This allows you to

save the Bass and Treble settings separately for each

mode.

Example:

FM tuner mode can have Bass +3 and Treble -1 while CD

mode can have Bass +2 and Treble +2.

Note:

Any adjustment to the Bass or Treble settings automatically

cancels the current EQ curve (if one is selected).

Reset

Confirmation Beep

Mute

Audio

Bass

Treble

Balance

Fader

Source Audio Memory

Press TUNE

or TUNE

momentarily to seek the

next strong station.

Press TUNE

or TUNE

for more than 2 seconds,

then release. "MANUAL" will momentarily appear in the

display. Press TUNE

or TUNE

momentarily to

move radio frequency up or down one step at a time. Press

and hold to advance quickly. If tuning is not adjusted for 5

seconds, the unit will return to seek tuning mode (default).

"AUTO" will momentarily appear in the display.

Press SCAN to preview strong stations on the current band,

pausing for 5 seconds at each. Press SCAN again to cancel.

Press LO/DX to activate local tuning for strong station

reception only. Press LO/DX again to cancel and resume

Distance tuning (default).

Press BAND to select between FM1, FM2, FM3, AM1 and

AM2 bands.

Press and hold BAND then press TUNE

to select

European frequency spacing. Press and hold BAND then

press TUNE

to select USA frequency spacing (default).

Up to 18 FM stations and 12 AM stations can be stored. To

store a station, select the desired band and station. Press

and hold the desired preset button (1-6) for more than

2 seconds. When stored, the preset number will appear in

the display. The station can be recalled anytime by pressing

the corresponding preset button.

Note:

Function buttons 7, 8, 9 and 0 apply to XM Radio and

MP3/WMA operation only.

Press AS/PS for more than 2 seconds to automatically store

the six strongest stations in the current band. Automatic

Local/Distance is activated during the initial band scan.

Press AS/PS for less than 2 seconds to scan presets 1-6 on

the current band, pausing for 5 seconds at each. Press

AS/PS again to cancel.

XDMR7700 OPERATION

AM/FM Tuner Operation

Seek Tuning

Manual Tuning

Scan Tuning

Local/Distance

Band

Frequency Spacing

Storing and Recalling

Station Presets

Automatically Store

Stations

Preset Scan

XDMR7700 OPERATION

XM Radio Activation

Activating Your XM Receiver

(Optional)

Tuning Modes

Basic Channel Selection

Direct Channel Selection

Category Recall

1. Press MODE to select XM Radio.

2. Verify channel 1 (XM Preview Channel) is playing.

3. Select Channel 0. The XM receiver’s eight character Radio

ID number will appear on the XDMR7700 display.

The Radio ID number is also located on the top of the

XM receiver unit (sold separately).

4. Record the number here for future reference:

5. Activate your XM Satellite Radio service.

To subscribe, log onto http://www.xmradio.com/activation or

call 1-800-852-9696.

Note:

You will need to keep your XDMR7700 turned on for at least

one hour after requesting activation to receive the full

channel line-up.

Press BAND to select between XM DIRECT, XM1 and XM2

bands.

Press TUNE

or TUNE

momentarily to select the

next available channel. Press and hold to advance quickly.

Press BAND to select XM DIRECT channel entry band.

“DIRECT” will momentarily appear in the display. Enter

the desired channel using preset buttons (1-0), then press

FUNC for 3 seconds to confirm the selected channel. If the

channel is not available, "CH ---" will momentarily appear

in the display and the current channel will be retained.

Press FUNC once to display the category of the currently

selected channel for 10 seconds. The CATEGORY icon will

appear on the display.

XM Radio - Operation

Andere Handbücher für XDMR7700

Inhaltsverzeichnis

Andere Dual Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung