Duplo DSF-2000 Bedienungsanleitung

Provided By

http://www.MyBinding.com

http://www.MyBindingBlog.com

Duplo DSF-2000

Sheet Feeder

Installation Manual

Specialized person only

SHEET FEEDER

DSF-2000

INSTALLATION MANUAL

Do not leave this Installation Manual at the installation site after installation.

Furthermore, do not leave tools used for the installation, at the installation site.

Retain this Installation Manual for future reference as it will be needed for subsequent

maintenance such as relocation.

TO SERVICING PERSONNEL

TABLE OF CONTENTS

1. Points to Note in Installation ..........................1

1-1. Before Installing .......................................1

1-2. Installation Location .................................1

1-3. Power Supply...........................................1

2. Standard Accessories .....................................2

3. Installation of DSF-2000 ..................................4

3-1. Preparations for DSF-2000......................4

3-2. Connecting the Power Supply .................5

3-3. Selecting the Downstream Processing

Unit ..........................................................6

1-2. Installation Location

1. POINTS TO NOTE IN INSTALLATION

Install the equipment in a place where the floor is strong enough to bear the mass of the unit,

which is as follows:

136 kg (299.56 lb)

Requirements for installation space are as follows:

Width ×Depth = 1100 ×750 mm (43.31 ×29.53")

Install the equipment in a horizontal and stable position.

Do not install the equipment near heaters or other heat-emitting appliances.

Install and use the equipment in an environment:

1-1. Before Installing

Turn off the unit, then unplug its power cord from the AC outlet.

Make sure that the power supply voltage and frequency in your area match the power

requirements indicated on the main name plate of the unit.

– where the temperature range is between 5 and 35°C,

– where the humidity range is between 20 and 85%

RH (no dew condensation),

– which is not subject to direct sunlight,

– which is subject to little or no vibration,

– where there are no harmful chemicals,

– which is reasonably free from dust,

– which is free from air-borne salt, and

– where the equipment will not be exposed to water.

1-3. Power Supply

This equipment shall be installed near the socket-outlet where the plug on the power supply

cord is easily accessible.

When you power other appliances from the same AC outlet, make sure that the combined

power consumption does not exceed the power supply capacity.

Confirm that the following parts are provided.

2. STANDARD ACCESSORIES

SHEET FEEDER

DSF-2000

INSTRUCTION MANUAL

SHEET FEEDER

DSF-2000

INSTALLATION MANUAL

Specialized person only

qwe

o!3

ruyi

!2!0 !1

!5 !6

No.

Qty. NameNo. Qty.

Power cord (only 120 V AC) 1

Connecting plate 1

Auxiliary paper feed plate A 1

Screw (HSKW5 ×12) 6

Screw (MSKW4 ×8) 4

Screw (MSKW3 ×6) 4

Instruction manual 1

Installation manual 1

Bridge 1

Upper bridge guide 1

Lower bridge guide 1

Front bracket 1

Rear bracket 1

Auxiliary stack guide A 1

Stack guide B 3

Power cord (only 220 to 240 V AC) 1

Name

2. STANDARD ACCESSORIES

Attach the auxiliary paper feed plate A.

Refer to “15. STACKING PAPER ON THE

PAPER FEEDER A AND ADJUSTING PAPER

FEED” in the instruction manual.

3. INSTALLATION OF DSF-2000

3-1. Preparations for DSF-2000

Auxiliary paper

feed plate A

Attach the front bracket, rear bracket,

upper bridge guide, and lower bridge

guide to the bridge.

qAttach the front and rear brackets to the bridge using

the screws (MSKW4 ×8) provided.

wAttach the upper and lower bridge guides to the front

and rear brackets using the screws (MSKW3 ×6)

provided.

Bridge

Front bracket

Rear bracket

Upper bridge guide

Lower bridge guide

3. INSTALLATION OF DSF-2000

When connecting the downstream processing unit, refer to its installation manual, instruction manual, and the

installation manual for the cabinet.

3-2. Connecting the Power Supply

Insert the power cord plug of the DSF-2000 into the outlet.

Adjust the angle of the ejection guide.

Normally use horizontally (in the shipped state). After installing, adjust only if necessary according to the using state.

Attach the connecting plate to the

DSF-2000 as shown in the figure.

(Use the screws (HSKW5 ×12) provided.)

Connecting plate

Attach the bridge.

Hook the holes on the bridge to the stepped collars on this unit, and secure the bridge using the four screws (HSKW5 ×12)

provided. To avoid the parts of this unit, attach the bridge as shown in the figure.

Connect the bridge cable to the connector of this unit.

Stepped collars

Screws (HSKW5 ×12)

Bridge cable

Bridge

Parts of this unit

Turn on the power of this unit.

3-3. Selecting the Downstream Processing Unit

Set the downstream processing unit to be connected on the maintenance menu.

Start button

Stop button

button

Clear

button

Escape

Jog dial

Power ON indicator

Display (LCD)

button

Function

Enter the maintenance menu.

Press the escape button once on the initial screen of the control panel. Turn the jog dial by three clicks towards the right,

and press the clear button once. A beep will be sounded. Turn the jog dial by 5 clicks towards the left, and press the clear

button once. Two beeps are sounded and “Maintenance Menu” will be displayed. Press the jog dial here to enter the

maintenance menu.

If pressed incorrectly halfway through, press the escape button several times, and repeat from the beginning at the initial

screen.

Maintenance Menu Select M. Mode

ROM Version

Turn the jog dial to display “Finisher Setting”, and press the jog dial to confirm.

Finisher Setting

None

Select the downstream processing unit to be connected.

When connecting the DBM-120 Sheet by Sheet

Turn the jog dial and select “DBM120” if connecting only the DBM-120 Sheet by Sheet, or “DBM120+120T” if connecting

also the DBM-120T, and press the jog dial to confirm.

Finisher Setting

DBM12O+12OT

3. INSTALLATION OF DSF-2000

When connecting the DBM-400 Sheet by Sheet

Turn the jog dial to select “DBM400”, and press the jog dial to confirm.

Finisher Setting

DBM4OO

Perform the following settings.

qTurn the jog dial to display “Feed Speed”, and press the jog dial to confirm.

Feed Speed

135O[mm/sec]

wTurn the jog dial to set the value to “145”, and press the jog dial to confirm.

Feed Speed

145O[mm/sec]

eMatch the contents registered with the DBM-400 Sheet by Sheet memory number to this unit.

<DSF-2000> <DBM-400 Sheet by Sheet>

A3 →Memory number 1: L = 420.0 mm W = 297.0 mm Saddle-stapling Folding

(16.54") (11.69")

A4 →Memory number 2: L = 297.0 mm W = 210.0 mm Saddle-stapling Folding

(11.69") (8.27")

11 ×17 →Memory number 3: L = 431.8 mm W = 279.4 mm Saddle-stapling Folding

(17") (11")

LTR →Memory number 4: L = 279.4 mm W = 215.9 mm Saddle-stapling Folding

(11") (8.5")

A3SR →Memory number 5: L = 450.0 mm W = 320.0 mm Saddle-stapling Folding

(17.72") (12.60")

Custom 1 (Initial setting: B4) →Memory number 6: L = 364.0 mm W = 257.0 mm Saddle-stapling Folding

(14.33") (10.12")

Custom 2 (Initial setting: B4) →Memory number 7: L = 364.0 mm W = 257.0 mm Saddle-stapling Folding

(14.33") (10.12")

Custom 3 (Initial setting: B4) →Memory number 8: L = 364.0 mm W = 257.0 mm Saddle-stapling Folding

(14.33") (10.12")

This ends the installation procedure.

Turn off the power of this unit.

This ends the setting of the downstream processing unit.

This setting will be effective from the next time the power is turned on.

Andere Handbücher für DSF-2000

Inhaltsverzeichnis

Andere Duplo Drucker Handbücher

Duplo

Duplo DC-646 Bedienungsanleitung

Duplo

Duplo DP-63P Bedienungsanleitung

Duplo

Duplo DSF-2000 Bedienungsanleitung

Duplo

Duplo DSC-10/20 Bedienungsanleitung

Duplo

Duplo DP-U850 Bedienungsanleitung

Duplo

Duplo Duprinter DP-203 Bedienungsanleitung

Duplo

Duplo DSF-2000 Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-440 Bedienungsanleitung

Duplo

Duplo ULTRA 200PRO Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-L220 Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-C100 Bedienungsanleitung

Duplo

Duplo Programatic Mark - II Bedienungsanleitung

Duplo

Duplo DP-J450 Bedienungsanleitung

Duplo

Duplo DSC-10/60i Bedienungsanleitung

Duplo

Duplo Duprinter DP-43E Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung