Duplo Programatic Mark - II Bedienungsanleitung

Provided By

http://www.MyBinding.com

http://www.MyBindingBlog.com

Duplo Programatic

Mark - II

Operation Manual

Duplo USA Corporation

3050 South Daimler Street

Santa Ana, CA 92705

949-752-8222 ◆949-752-7766

PROGRAMATIC

MARK - II

OPERATION MANUAL

Control Panel:...................................................................................................................... 5

Display Screen:.................................................................................................................... 6

Instruction for Keys:............................................................................................................ 7

How to use in Manual Operation:....................................................................................... 9

Making a New Program:..................................................................................................... 9

How to use the Cut & Store Program: .............................................................................. 12

How to use Step and Repeat Program:.............................................................................. 14

How to use Step and Repeat Program with a Gutter Trim:.............................................. 16

How to Recall Existing Programs:.................................................................................... 18

Control Panel:

8 9 PROG

BASIC SCREEN 456LAST

1 2 3 NEXT

−

−0 X END

RUNAUTO CUT&

STORE BRAKE

RELS

SLOW

REV

FAST

REV

SLOW

FWD

FAST

FWD

PROGRAMATICMARK - II

Display Screen:

NOTE: The “C:” size may very from cutter to cutter.

C: Current cut position.

The backgauges current position.

PROG: Program number.

There are 9 programs from 1 - 9. The PROG: 0 is for parameter

setting, any changes on the parameter should be made in the

configuration mode.

1: 2: 3: 4: 5: 6: 7: 8: Cut position.

It allows for 9 programs with 8 cuts each. Two or more programs can

be combined. A total of 72 cuts can be stored.

C: 26”125 PROG: 1 AUTO

1: 17”000 2: 11”000

Instruction for Keys:

(0-9) : To key in a size.

(PROG) :

Selection programs. There are 9 programs from 1 - 9.

For example: If you want to select the program number 1, press the PROG

button, (the screen shows PROG: ❑), then press 1 to recall that program from

memory. The cursor (❑) will be flashing over the last digit on cut position #1

(00”00❑).

(LAST):

Last cut position. You can use this key to select cut position, checking,

correction, and memory. i.e. 1: 04”000 2 : 05”000, press (LAST), the

cursor will shift to the previous (or last) cut position.

(NEXT):

Next cut position. Use this key to select cut numbers, checking,

correction and memory.

( END ) : When you finish a program, press the (END) button. It will give you a

confirmation sound. Once the key is pressed it will clear all

cut numbers in the back and the screen appears the first cut mark.

: Fast forward. Press & hold down the key, the backgauge will move

fast forward.

: Slow forward. Press & hold down the key, the backgauge will move

forward slowly.

: Fast reverse. When the key is pressed and held down, the backgauge

moves fast to the rear and stops at the rear point, after the key is

released the backgauge moves forward 2 mm automatically.

FAST

FWD

SLOW

FWD

FAST

REV

: Slow reverse. When the key is pressed and held down, the backgauge

moves slowly to the rear and stops at the rear point, after the key is

released the backgauge moves forward 2 mm automatically.

: Brake Release. 660 model: The key need not be pressed, just push

in the hand wheel and then you can make a micro adjustment. On the 486

model: when you make micro a adjustment you need to press & hold down this key.

: Cut & Store. First select the program number, then press (CUT &

STORE), the screen shows C & S. You can now setup the required cut

size by pressing (FWD/REV) keys and using the hand wheel. When the cut size is

selected, make a cut and the cut position will be stored automatically.

: Auto. You have to confirm the start position of the shift before this key

is pressed. Press the key, it will store the desired cut positions in order.

: Run. In AUTO mode, press (RUN), it will run (or skip) over a certain

cut size which is not used, and will go to the next cut in memory.

: Minus (−)can be used together with Multiplication (×). These

keys are used for making multiple cuts into more pieces (i.e. business

cards).

SLOW

REV

BRAKE

RELS

CUT&

STORE

AUTO

RUN

− ×

How to use in Manual Operation:

Turn on the power to the cutter, wait until the backgauge moves back and will

recalibrate the position and this display appears:

NOTE: There will be a cursor (❑) flashing over at the last number, this is the work area.

Manual mode has two operating controls:

1) The backgauge moves with the manual keys

2) If you press (0 - 9) entering 17000, the screen appears:

Press (RUN), the backgauge will move to the requested position.

Making a New Program:

Turn on the power to the cutter, wait until the backgauge moves back and will

recalibrate the position and this display appears:

NOTE: There will be a cursor (❑) flashing over at the last number, this is the work area.

Select a program number from 1-9, if you press (PROG) (1) this screen appears:

C: 26”125 PROG: 1

1: 00”00❑2: 00”000

FAST

FWD SLOW

FWD FAST

REV SLOW

REV

C: 26”125 PROG: 1

1: 17”00❑2: 00”000

C: 26”125 PROG: 1

1: 00”00❑2: 00”000

C: 26”125 PROG: 1

1: 00”00❑2: 00”000

Inhaltsverzeichnis

Andere Duplo Drucker Handbücher

Duplo

Duplo DP-J450 Bedienungsanleitung

Duplo

Duplo DSC-10/60i Bedienungsanleitung

Duplo

Duplo DP-63P Bedienungsanleitung

Duplo

Duplo ULTRA 200PRO Bedienungsanleitung

Duplo

Duplo Duprinter DP-43E Bedienungsanleitung

Duplo

Duplo DP-U850 Bedienungsanleitung

Duplo

Duplo Duprinter DP-203 Bedienungsanleitung

Duplo

Duplo DSF-2000 Bedienungsanleitung

Duplo

Duplo DSF-2000 Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-L220 Bedienungsanleitung

Duplo

Duplo DC-646 Bedienungsanleitung

Duplo

Duplo DSF-2000 Bedienungsanleitung

Duplo

Duplo DSC-10/20 Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-C100 Bedienungsanleitung

Duplo

Duplo DUPRINTER DP-440 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung