6
English
one use the cable to carry the tool or pull it; also, it is
forbidden to switch off the tool by pulling the power
supply cable. Protect the cable against heating, contact
with kerosene-based bodies, with sharp edges or
mobile parts of the tool. A power cable that is damaged
or spliced increases the danger of electric shock.
• When working in open air, use extension cords
designed for this type of work, which will reduce the
danger of electric shock.
Personal protection recommendations
•Be cautious when working with power tools, and
carefully plan your actions. Do not use the tool when
fatigued, or under the inuence of drugs, alcohol or
medicines. Careless handling may result in serious
injuries.
•Use personal protection equipment. Always wear
protective goggles. When necessary, use respirators,
non-slipping boots, hard hats and earplugs. The use
of personal protection equipment is one of the factors
that reduce the risk of injuries.
• Avoid incidental activation of power tools. Before
inserting the plug, make sure that the power switch is in
OFF position. When carrying the tool, take your ngers
off the main switch, which will reduce the possibility of
incidental activation.
• Before switching on the tool, remove any wrenches
and other objects from its rotating parts. A wrench left
in the rotating unit may result in serious injuries.
• Do not apply excessive force, take a stable position
and always try to keep balance - this will facilitate
control over the tool.
•Do not wear loose clothes or freely-hanging
jewellery. Hair, parts of garment and gloves should
be protected against contact with moving parts of the
power tool.
• If the tool is equipped with a dust collection device,
make sure that the device has been activated and
used properly. Use of such devices helps reduce the
concentration of dust at the workstation.
Use and handling of power tools
•The persons with lowered psychophysical or mental
aptitudes as well as children can not operate the power
tool, if they are not supervised or instructed about use
of the power tool by a person responsible for their
safety.
• Do not overload the tool. Power tools are to be used
only in operations, to which they have been designed,
which will ensure safety and help achieve better
results.
•Do not use power tools with a damaged power
switch. A tool that cannot be switched on and off in a
controlled manner is potentially dangerous and must
be repaired immediately.
• Before adjustment operations, replacement of
attachments, and during storage, remove the power
tool plug from the mains socket. This eliminates the
risk of the tool being unintentionally activated.
•The tool should be stored out of children's reach.
Do not allow the use of power tools by persons who
have not read this manual and are inexperienced. In
the hands of an inexpert person, the tool may be dan-
gerous both for the operator and his environment.
•Take proper care of the tool condition. Monitor the
axial run-out and stability of movable parts' joints, and
pay proper attention at any faults that may result in the
tool damage. Bad condition of power tools is a frequent
cause of accidents.
•Cutting tools should be kept clean and must be well-
sharpened. Cutting tools with sharp cutting edges,
which are properly xed reduce the risk of seizure and
facilitate the control over power tools.
•When using power tools and its accessories, follow
the instructions listed in this manual. During work with a
specic type of power tools, follow recommendations,
taking into account operational conditions and the type
of job performed.
Service of power tools
Your power tool should be serviced only by qualied
specialists, with the use of recommended spare parts.
This will guarantee labour safety, when your tool is
being applied.
Safety guidelines during
power tool operation
Before commencing operation
• The power tool is designed for polishing only, never
use the power tool as an angle grinder.
•Regularly check the polishing bonnet for wear,
impurities or hardened areas.
• Use the accessories, permissible revolutions per
minute of which exceed the number of revolutions
per minute of the power tool spindle. Follow the
manufacturers' recommendations concerning the
application of accessories.
•Do not operate accessories, the dimensions of
which (external and bore diameters) differ from the
recommended ones.
•It is strictly forbidden to use saw discs with this
power tool.
• Remove the wrench from the rotating part of the
power tool to avoid injury.
During operation
• Avoid contact between the polishing bonnet and
the power supply cable. The cable may twist over the
rotating polishing bonnet.
• Do not use jaw vice to x the power tool.
• Never use damaged or torn polishing bonnets.
•Bring the power tool to the billet only in the operating
mode. Start the processing only after the accessory
gains its maximal speed.
• Avoid electric tool motor stop, when loaded.
• Beware of recoil (sudden push back) while operating
the power tool. The recoil may be caused by abrupt
contact of the polishing accessory with the part being
processed. In order to decrease the possibility of
recoil, always use an additional handle supplied and
strictly follow operating instructions.
•Maintain a stable position while working, hold your
electric tool with both hands.
• During operation do not cover the ventilation slots
with your hands.
•During operation watch the position of a power cable
(it should always be positioned behind the tool). Do not
allow it to whip around your legs or arms.
•Keep your hands safely away from the rotating parts
of your electric tool.
