Dynabrade Dynangle 14200 Bedienungsanleitung

Disassembly Instructions - 0.7 hp. Dynangle Air Motor

Models: 14200

Important: Use these instructions along with the tool parts page or manual.

Notice: Shut off the air supply and depress throttle lever to deplete the remaining air.

• Carefully disconnect the tool from the air supply hose. • Remove the cover and the abrasive

belt. • Use the Special Repair Tools designed for the disassembly and assembly of this motor.

Motor Disassembly:

1. Use a 1/8" hex key to loosen the 95530 Screw.

Remove the motor from the belt housing.

1/8" hex key

1/8" Hex Key

2. Use a 19 mm wrench to hold the motor spindle. By hand, or with groove pliers, grasp the

drive wheel and remove it. Turn counterclockwise.

19 mm Wrench

3. Carefully fasten the 01739 Housing in a vise with aluminum or bronze jaws so that the

spindle is pointing up.

Use a 1-1/2" crowfoot wrench to remove the 01748 Exhaust Cover.

Turn counterclockwise.

Remove the 01744 Silencer.

1-1/2" crowfoot wrench

Pull the motor out of the housing.

4. Fasten the 96346 Bearing Separator (2") around the 01028 Cylinder. Place the separator

and the motor in the 96232 Arbor Press (#2) so that the rotor spindle is pointing down.

Use a 5/32" or 4 mm diameter flat end drive punch to push the rotor out of the 02649

Bearing.

96346 Bearing Separator

5. Use the 96213 Bearing Removal Tool and the arbor press to remove the 02649 Bearing

from the rear bearing plate.

96346 Bearing Separator

96213 Bearing Removal Tool

6. Fasten the 55025 Rotor in the vise with aluminum or bronze jaws and use an adjustable

wrench to remove the 01708 Rotor Nut. Turn counterclockwise.

Remove the 01007 Bearing, 01008 Bearing Plate, shims, and 01010 Spacer.

Motor Disassembly Completed.

Clean and inspect parts before assembling.

Assembly Instructions - 0.7 hp. Dynafile III Air Motors

Motor Assembly:

1. Install the 01010 Spacer onto the rotor.

Install .003" (~0.80 mm) shim thickness into the 01008 Front Bearing Plate.

Install the 01007 Bearing into the front bearing plate.

Install the bearing and plate onto the rotor.

.003" (~0.80 mm)

shim thickness

01010 Spacer

2. By hand, install the 01708 Rotor Nut. Pull the front bearing plate forward to take movement

out of the bearing. Check the clearance between the rotor and plate.

Use a .001" (~0.03 mm) thick feeler gauge. Notice: The clearance should be

.001"-.0015" (~0.03-0.04 mm). If the rotor/plate clearance needs adjustment, repeat

steps 1 and 2. Remove or add shims as required.

.001"-.0015"

(~0.03-0.04 mm)

3. Use a 19 mm crowfoot and a torque wrench to tighten the 01708 Rotor Nut.

(T to 17 N•m/~150 in. lbs.)

T to 17 N•m/~150 in. lbs.

Andere Dynabrade Sander Handbücher

Dynabrade

Dynabrade 52631 Bedienungsanleitung

Dynabrade

Dynabrade Dynorbital Supreme 56800 Leitfaden

Dynabrade

Dynabrade 5700 Bedienungsanleitung

Dynabrade

Dynabrade 09L1000 Bedienungsanleitung

Dynabrade

Dynabrade 52596 Bedienungsanleitung

Dynabrade

Dynabrade Dynorbital 57600 Bedienungsanleitung

Dynabrade

Dynabrade 10170 Bedienungsanleitung

Dynabrade

Dynabrade 59306 Leitfaden

Dynabrade

Dynabrade 51520 Kurzanleitung

Dynabrade

Dynabrade 58035 Installations- und Betriebshandbuch

Dynabrade

Dynabrade Dynorbital-Spirit 21000 Bedienungsanleitung

Dynabrade

Dynabrade 50371 Montageanleitung

Dynabrade

Dynabrade 52414 Bedienungsanleitung

Dynabrade

Dynabrade Mini-Dynorbital Silver Supreme 69500 Leitfaden

Dynabrade

Dynabrade 58050 Montageanleitung

Dynabrade

Dynabrade 48500 Leitfaden

Dynabrade

Dynabrade 57700 Benutzerhandbuch

Dynabrade

Dynabrade 57220 Benutzerhandbuch

Dynabrade

Dynabrade Dynorbital 57130 Bedienungsanleitung

Dynabrade

Dynabrade 52900 Betriebsanleitung

Dynabrade

Dynabrade 50304 Bedienungsanleitung

Dynabrade

Dynabrade 51420 Bedienungsanleitung

Dynabrade

Dynabrade 18066 Leitfaden

Dynabrade

Dynabrade 57101 Benutzerhandbuch

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Craftsman

Craftsman 351.215131 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Clarke

Clarke EZ Sand Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung