Dynalink 56USBPRO Bedienungsanleitung

56K USB Pro Modem

Quick Setup Guide

56USBPRO

56K USB PRO Modem Quick Set-up Guide

Introduction

This Quick Setup Guide summarises the modem installation in

four simple steps. Please follow each step exactly as described.

Upon completion of Step 4 you can be certain that your modem

is correctly installed.

To prepare for installation follow the instructions to decompress

the drivers to your hard disk as described in Step 1 of this Guide.

There are two floppy disks:

1. Modem driver files for Windows®98,

ME, 2000 and XP (compressed).

2. A full modem users manual that contains

installation & uninstallation instructions.

The Computer Associates®CD that you received with

your modem contains:

• BitWare software, which can be used for sending and

receiving faxes with your PC and Dynalink modem.

• Other complimentary software.

To access all software just insert the CD and a menu will load

automatically. If not, click Start – Run and enter d:\msetup.exe

(substitute d: with your CD drive letter), then click OK. Other CDs

are supplied by Internet Service Providers (ISPs) to enable you

to establish an Internet connection. Some fees may be payable

– please check the ISP’s CD for more information. Once on the

Internet you can visit Dynalink Modems’ web site at

www.dynalink.com.au (Australia) or www.dynalink.co.nz (New

Zealand) to access further helpful information.

Before you start

You must first decompress the modem drivers from the floppy disk supplied into

your hard disk.

1. Insert the floppy disk labeled “V.90/K56Flex FAX/MODEM Driver” into your

floppy driver.

2. Go to Start-Run. Browse to My Computer–Floppy (A:). Highlight the file

UFM560.exe, click Open-OK.

3. Click OK to start the WinZip Self-Extractor. When asked Unzip to folder, either

enter C:\DynalinkUSB, or enter a new folder of your choice, and then click

the Unzip button. The driver files will be copied to your hard disk in the folder

DynalinkUSB, or the folder you have chosen.

Connect the modem to your PC

Connect the enclosed phone cable to the LINE jack of the modem and a wall

phone jack, then connect the enclosed USB plug to both the modem and a USB

port on your PC. Once the modem has been connected to your PC a prompt will

load – please proceed to Step 3.

USB Hub Users: If you intend on using the modem via a USB Hub, the Hub must

be self-powered. The modem consumes more power than a bus-powered port

can normally supply. Self-powered USB Hubs, which overcome this issue, are

available from Dynalink.

Install the modem drivers

System will report that it has detected a new device Atlas Modem Board.

Windows XP:

Click Next. Select Install from a list or specific location - Next. Browse to the

folder C:\DynalinkUSB\winxp, or the folder you have chosen in Step 1 (3). Click

Next. System will report Found USB V.90 56k FAX MODEM. If a compatibility

message appears, click Continue Anyway. Click Finish to complete driver installation.

Windows 2000:

Click Next. Select Search for a suitable driver for my device – Next. Click Specify

a location. Browse to the folder C:\DynalinkUSB\win2k, or the folder you have

chosen in Step 1 (3). Click Next-Next. If Digital Signature Not Found appears

click Yes to continue and Finish to complete driver installation.

Windows ME:

Click Next. Select Specify the location of the driver – Next. Click Specify a

location. Browse to the folder C:\DynalinkUSB\winme, or the folder you have

chosen in Step 1 (3). Click Next-Finish. Windows will continue to detect another

device. Click Next and repeat the above process to complete driver installation.

Windows 98:

Click Next. Select Search for the best driver for your device – Next. Click Specify

a location. Browse to the folder C:\DynalinkUSB\win98, or the folder you have

chosen in Step 1 (3). Click Next-Finish. Windows will continue to detect another

device. Click Next and repeat the above process to complete driver installation.

Check the modem can talk to the pc

Windows XP/2000:

1. Click Start–Settings–Control Panel–Phone and Modem Options.

2. You will see USB V.90 56K FAX MODEM listed next to a COM Port. Note down

the COM port number in this box [ ] for future reference.

3. Click Modems.

Highlight USB V.90 56K FAX MODEM-Properties–Diagnostics–Query Modem

and wait. If a table of ATI…'85 responses is reported, then the modem and

computer are communicating. If your modem fails to respond, or you are

getting an error message such as CANNOT OPEN PORT, please refer to the

Troubleshooting section.

Windows 98/ME:

1. Click Start -Settings–Control Panel–Modems–Diagnostics.

2. You will see USB V.90 56k FAX MODEM listed next to a COM Port. Note down

the COM port number in this box [ ] for future reference.

3. Highlight the COM port and click More Info. If a table of ATI…'85 responses

is reported, then the modem and computer are communicating. If your modem

fails to respond, or you are getting an error message such as CANNOT OPEN

PORT, please refer to the Troubleshooting section.

The modem has been installed successfully and passed all our tests. Any

problems that arise when the modem is used by other applications are not

related to the installation of the modem, but to the setup of the software using

the modem. We suggest that you now proceed to the next section, as the Internet

will give you access to our website support area. If you have problems during

this step you can be confident that the problem is not a basic modem installation

problem, but rather the setup of the Internet software.

56K USB PRO Modem Quick Set-up Guide

The internet

In order to connect to the Internet you will need to establish an account with an

Internet Service Provider (ISP). Enclosed with your modem is a CD containing

an introductory offer from an ISP. Once you have registered with an ISP, they will

provide you with assistance regarding connecting to the Internet and setting up

an e-mail account.

Once you are connected to the Internet, you will find further information on

Dynalink Modem’s World Wide Web site at www.dynalink.com.au/support

(Australia) or www.dynalink.co.nz/support (NZ). Here you can learn how to

setup the Bitware software for fax, extensive troubleshooting information,

downloads and much more information.

Fax Software (optional)

The Bitware Fax software provided with your modem on the enclosed Computer

Associates CD allows you to fax with your modem.

To install Bitware, insert the Computer Associates CD. If a menu does not load

automatically, click Start – Run and enter d:\msetup.exe (subs titute d: with your

CD drive letter), then click OK. Select the BitWare option, then click Install and

follow the on-screen prompts. There is also an online User’s Manual on the CD.

To read this manual you will need Acrobat Reader, which can be installed by

running msetup.exe again.

Troubleshooting

NO DIALTONE is reported

Click Start–Settings-Control Panel-Modems–Properties–Connection–Advanced.

Under Extra Settings, enter X3.

Check you are using the phone cable that came with the modem - not a phone

cable normally used with a phone.

Check the phone cable is plugged into the LINE jack of the modem, and the

other end is plugged into a phone jack on the wall.

Eliminate any cables or devices between the phone cable and the wall jack,

such as fax switches or extension phone cables.

Windows does not detect the modem.

Check the modem’s USB cable is connected to both your modem and USB

port of your PC.

Verify your PC is USB ready. A program which can do this for you is available

for download from our website (www.dynalink.co.nz).

Verify your PC’s BIOS has USB IRQ enabled. This is an advanced procedure,

so please contact your computer dealer or check your PC’s manual for

instructions.

When clicking the More Info (or Query modem) button, an error is reported.

Check you have clicked on the COM port your modem is attached to.

Ensure no other programmes are using the modem - exit all programmes

before running More Info.

A list of ATI responses are reported, but some of them report ERROR.

This is normal - not all AT commands are supported by all modems.

ERROR is reported after typing at&f

Check you are typing at&f - it is normal not to see these characters when first

entered. Try quitting out of Hyperterminal and starting again.

56K USB PRO Modem Quick Set-up Guide

Dynalink warrants this product against defects in materials and workmanship

for a period of twelve months from the original date of purchase. We will, at our

discretion, repair or replace the faulty unit, free of charge, provided it is returned

to us with proof of purchase from an authorised dealer within the warranty

period. Return delivery after repair will be paid for by Dynalink. We reserve the

right not to repair or replace goods that:

have been mishandled, abused or not installed according

to the guidelines as outlined in the instructions.

have been subjected to a power surge from other

equipment or other external factors.

have been altered or modified.

Warranty

Always check that your hardware is installed correctly. Check our web site for

the latest information and troubleshooting guide. If you have difficulties, contact

Dynalink Technical Support for issues relating to installation and operation.

If possible, visit Dynalink's on-line support area at:

New Zealand www.dynalink.co.nz/support

Australia www.dynalink.com.au/support

Contact Dynalink’s Technical Support:

Help

Australia

Phone 1800 653 962

Fax 1800 063 962

(Monday-Friday: 8:30am-5:30pm)

New Zealand

Phone 0800 653 962

Fax 0800 503 962

(Monday-Friday: 8:30am-7:30pm)

NZAU-56USBPRO-QG2

Inhaltsverzeichnis

Andere Dynalink Modem Handbücher

Dynalink

Dynalink WM1080A Bedienungsanleitung

Dynalink

Dynalink RTA1025WV6 Bedienungsanleitung

Dynalink

Dynalink 1456VQE-C Bedienungsanleitung

Dynalink

Dynalink 56K e-modem III Bedienungsanleitung

Dynalink

Dynalink ALE800 Bedienungsanleitung

Dynalink

Dynalink ALE070 Bedienungsanleitung

Dynalink

Dynalink RTA770 Bedienungsanleitung

Dynalink

Dynalink RTA1046VW Bedienungsanleitung

Dynalink

Dynalink DY56EXT3 Bedienungsanleitung

Dynalink

Dynalink u90E-RURALII Bedienungsanleitung

Dynalink

Dynalink RTA1320 Bedienungsanleitung

Dynalink

Dynalink RTA1320 Bedienungsanleitung

Dynalink

Dynalink RTA100+ Bedienungsanleitung

Dynalink

Dynalink WLG25USB Bedienungsanleitung

Dynalink

Dynalink RTA1025W Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung