Dyness DYN-B4850 Handbuch

Dyness battery and Growatt off grid inverter Setup

Check List:

Dyness B4850 * 4

Power cable*1 pair

Parallel cable*3 pairs

Communication cable Bat-Inv*1

Communication cable Bat-Bat*3

Growatt SPF 5000TL HVM-ES

Before start, make sure battery and inverter size match.

Follow Dyness user manual to check details, it is recommended to

use battery in 1: 2 configuration.

In our case now, 5kW inverter connects to 9.6kWh battery.

Step 1 : Cable connect in inverter

Keep both inverter and battery completely off.

Connect power cable and comm cable to inverter first.

Note: Comm cable has label on, make sure the inverter side goes

to battery side, inverter side to the inverter BMS side ,battery side

left for later on in battery connection.

Step 2 : Dial DIP switch on master

Make sure host battery DIP is 0010,slaves 0000

Step 3 : Cable connect in battery

Keep batteries off, connect power cable 、parallel cable、

communication cable Bat-Inv and comm cable Bat-Bat as above.

1. Comm cable from the host CAN IN port to the inverter CAN port

2. Comm cable from the host CAN OUT to slave1 CAN IN,slave1

CAN OUT to slave2 CAN IN….

3. Power cable should be connected diagonally ,one is connected

at the top socket and another one is at the bottom.

Step 4 : Breaker/Fuse between inverter and battery

Connect DC breaker or Fuse between inverter and battery to protect

both products.

Step 5 : Switch on all the B4850 power switch,then press the

host SW button about 3S to wake up it,all the slaves will be

woken up automatically.

Step 6: Turn on the DC breaker

Step 7: Power on the inverter

Step 10: Battery and inverter are connected!

Now inverter is started, it should show the battery voltage ,battery

and inverter are connected!

Step 11: Inverter setup

Long press ENTER to set, make sure 05 are properly set as

below:

05 LI type(Lithium)

21 Cut off SOC of the battery,20% default is OK.

Step 12: You are ready to go

Step 13: Shut Down

1 Remove all the load

2 Disconnect PV/Grid

3 Turn off DC breaker between the battery and inverter.

4 Turn off the inverter power switch,shut down the inverter

5 Long press SW button to power off the battery, then switch off all

the batteries’ Power switch

Inhaltsverzeichnis

Andere Dyness Batteriepack Handbücher

Dyness

Dyness PowerRack HV4 Bedienungsanleitung

Dyness

Dyness PowerDepot H5B Bedienungsanleitung

Dyness

Dyness RV12100 Bedienungsanleitung

Dyness

Dyness B3 Bedienungsanleitung

Dyness

Dyness Tower T Series Bedienungsanleitung

Dyness

Dyness TowerESS Bedienungsanleitung

Dyness

Dyness POWERCUBE Series Bedienungsanleitung

Dyness

Dyness B4850 Bedienungsanleitung

Dyness

Dyness B51100 Bedienungsanleitung

Dyness

Dyness DL5.0C Bedienungsanleitung

Dyness

Dyness WIFI-M01 Bedienungsanleitung

Dyness

Dyness Tower ESS Bedienungsanleitung

Dyness

Dyness POWERBOX Pro Bedienungsanleitung

Dyness

Dyness B48100 Bedienungsanleitung

Dyness

Dyness A48100 Bedienungsanleitung

Dyness

Dyness Junior Box Bedienungsanleitung

Beliebte Batteriepack Handbücher anderer Marken

Acumentrics

Acumentrics PACK-POWER SYSTEM Bedienungsanleitung

ACDC Dynamics

ACDC Dynamics SPF12-50 Bedienungsanleitung

Aegis

Aegis ABL-72020P Bedienungsanleitung

Growatt

Growatt APX 5.0P-S0-US Bedienungsanleitung

EGO

EGO BAX1300 Bedienungsanleitung

CyberPower

CyberPower BCA Series Bedienungsanleitung

Intermec

Intermec 700 Series Bedienungsanleitung

Dometic

Dometic PLB40 Bedienungsanleitung

V-TAC

V-TAC VT-48280-W2 Bedienungsanleitung

Valence

Valence RT Bedienungsanleitung

Nikon

Nikon MB-D14 Bedienungsanleitung

IOGear

IOGear GBP24V Series Bedienungsanleitung

Inventus Power

Inventus Power PROTRXion S-12V100-TRX-HD Bedienungsanleitung

Clas Ohlson

Clas Ohlson PW-290A Bedienungsanleitung

EINHELL

EINHELL MULTI-Ah Power X-Change Plus Bedienungsanleitung

Samsung

Samsung EB-U3300 Bedienungsanleitung

ECTIVE

ECTIVE LC Series Bedienungsanleitung

Narada

Narada 12REXC70 Bedienungsanleitung