Dyson Airblade AB02 Bedienungsanleitung

Owner’s Manual

5year parts limited warranty

120v – US specification

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 1

Why Dyson developed the

AirbladeTM hand dryer

Paper towels have always been expensive, labor-intensive,

and bad for the environment. Conventional hand dryers are

more economical, but are notoriously frustrating to use.

Finally, a hand dryer that works properly.

The Dyson AirbladeTM was engineered to be the fastest, most

hygienic hand dryer available. It is also energy-efficient and

cost-effective to run.

Fastest dry

The AirbladeTM hand dryer dries hands differently. It uses a high

velocity blade of air to literally wipe water from hands, leaving

them completely dry in just 12 seconds.

1Thank you for buying the Dyson AirbladeTMhand dryer.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.If you have

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,to the service panel.

3. Installation work and electrical wiring must be done by qualified person(s) in

accordance with all federal, state and local applicable codes and standards,

including fire-rated construction.

4. When cutting or drilling into wall or ceiling,do not damage electrical

wiring and other hidden utilities.

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 2

The most hygienic hand dryer

The Dyson AirbladeTMuses a HEPA filter to remove over 99.9%

of bacteria from the air used to dry hands and has anti-microbial

additives integrated into its surfaces.

Uses up to 80% less energy

Conventional hand dryers rely on inefficient motor technology and high power

heating elements to dry hands, often taking over 22 seconds and wasting energy.

The AirbladeTM hand dryer is powered by the energy efficient 1400w Dyson

Digital Motor, has no heating element, and takes only 12 seconds to dry

hands. As a result, the AirbladeTM hand dryer uses up to 80% less energy per

drying cycle.

1. Insert your hands and the

AirbladeTM hand dryer will start

automatically.

2. Withdraw your hands slowly

upwards through the air a

couple of times to dry hands

thoroughly in 12 seconds

or less.

How to use

The AirbladeTM hand dryer generates a high velocity blade of air

that wipes hands dry in just 12 seconds.

Cost-effective

It is very expensive to procure, stock and dispose of paper towels.

Conventional hand dryers consume large amounts of electricity.

The AirbladeTMhand dryer, with a combination of high reliability,

low maintenance, and energy efficiency, offers considerable cost

savings throughout its lifetime. It uses up to 80% less energy than

conventional hand dryers, so running costs are considerably

lower. When compared to paper towels, the AirbladeTM hand

dryer offers operating cost savings of nearly 98%.

ENG

Dyson AirbladeTM

US $26.03

Paper towels

US $1200

Operating costs based on

200 dries/day and 300 days/year.

Paper towel costs based on

US $0.01/towel and 2 towels/dry.

They do not include any labor and

costs associated with dispensing

and disposing of paper. Dyson

AirbladeT M costs are based on

US $0.09/kWh and 12 seconds

dry time.

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 3

READ BEFORE PROCEEDING FURTHER

CAUTION: Risk of electric shock! Do not remove casing or attempt repair unless

unit is being serviced by qualified service personnel. If casing is removed or handled

improperly the internal components of the Dyson AirbladeTM may cause harm or

become permanently damaged.

WARNING: To reduce the risk of fire or electric shock, do not expose the internal

mechanism/components of this unit to rain or moisture.

General notes:

The instructions contained within the Owner’s Manual must be read carefully before attempting

to install the AirbladeTM hand dryer. Read and retain for future reference.

Failure to accurately follow the instructions may result in the incorrect operation of the AirbladeTM

hand dryer,damage to property and/or personal injury.

Dyson will not be held liable for any damage to property or personal injury as a result of failure

to comply with the instructions contained herein.

Do not use AirbladeTM hand dryer for anything other than drying hands.

The AirbladeTM hand dryer must be grounded properly.

Trouble free operation and safety can only be continued by using genuine Dyson spare parts.

WARNING:

This product may contain substances known to the state of California to cause cancer,birth defects

and other reproductive harm. Wash hands after handling.

Important Safety

Information

Contents

4 Glossary of Terms

Contents of Box

•Tools needed

5 Installation Procedures

•Electrical requirements

6•Positioning

•Mounting Bracket

7• Removing the Fascia Cover

8•Connecting to Electrical Supply

9• Refitting Front Fascia & Access Panel

10 Final Inspection

Cleaning and Maintenance Advice

11 Troubleshooting

12-14 Limited Warranty Information

15 Contacting Dyson

READ AND SAVE THESE INSTRUCTIONS

Dyson AirbladeTM hand dryer

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 4

Contents of Box

Dyson AirbladeTM hand dryer

Information pack containing:

•Owner’s Manual including warranty information

•Registration information and reply envelope

•Mounting Template

•Tamper proof service tool

•Mounting bracket

To install the AirbladeTM hand dryer you will need:

Electric drill & appropriate bits

Phillips screwdriver

Flat-head screwdriver

Level

Pencil or marking tool

Appropriate electrical fittings

(6) screws, toggle or masonry bolts and appropriate fittings.

(Recommended minimum size of 1/4”)

Dyson recommends the use of protective clothing,eyewear

and materials as necessary.

Glossary of Terms

Dyson AirbladeTM hand dryer

Air slots

Rating plate

Access panel Air inlet

Sensors x 4

Front fascia

Dyson Digital Motor

HEPAfilter

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 5

Dyson AirbladeTM hand dryer

Electrical requirements

Installation Procedures

Check that the electrical

supply will correspond with the

rating plate located on the

lower left side of the unit.

If the unit is connected to any

electrical supply other than

what is stated on the rating

plate of the unit, permanent

damage or improper/unsafe

operation of the AirbladeTM

may result.

A means for all pole

disconnection must be

incorporated in the fixed wiring

to the appliance in accordance

with local wiring regulations.

Installation work and

electrical wiring must be

done by qualified person(s)

in accordance with all federal,

state and local applicable

codes and standards,

including fire-rated

construction.

The Dyson AirbladeTM

requires:

Aseparate or dedicated circuit

Aminimum 15amp time delay

fuse or circuit breaker

If you have any questions

on the installation please

call our Dyson Helpline toll

free at 1-888-DYSON-AB

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 6

Select a location that will allow

accessibility to the AirbladeTM

and proper clearance from

surroundings and floor. Make

sure that the unit is installed in

compliance with all building

codes and/or regulations.

Position the mounting template

provided on the wall where the

AirbladeTM hand dryer is to be

installed.

Recommended heights are

shown in Fig 1,but may need to

be adjusted for each individual

installation.

Mark the 6 mounting holes as

highlighted in Fig 1.

Verify marks are level and in

the correct locations.

Drill holes where marked.

Electrical supply connection

2”

Bracket mounting height:

39” adult male height

36” adult female height

32” child/wheelchair user height

29.75”adult male height

26.75”adult female height

22.75”child/wheelchair user height

Floor

Positioning

Installation Procedures

Fig 1

There are two electrical

entrance locations available to

ease with the installation of the

AirbladeTM.Mark only one of

the electrical supply locations

illustrated in Fig 1 and drill

the hole large enough to

accommodate the incoming

flexible metal conduit and

supply cable.

Mounting Bracket

Fig 2

x 2

Ensure that marks are level and

in the correct location as

illustrated in Fig 2.

Securely fasten the mounting

bracket to the wall.

Dyson AirbladeTM hand dryer

ENG

WARNING: Before

beginning any installation

work you must confirm the

following:

Make sure that the electrical

supply has been disconnected

or switched off before attempting

installation to avoid the risk of

electrical shock or electrocution.

Ensure no pipe work

(gas, water, air) or electrical

cables, wires or ductwork are

located directly behind the

drilling area.

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 7

Dyson AirbladeTM hand dryer

Installation Procedures

Fig 5 Fig 6

Removing the

Fascia Cover

WARNING: Use caution

when removing casing.

The casing may have sharp

edges/corners which may

cut or cause harm.

Place the AirbladeTM hand dryer

face up on a dry and clean

work surface to protect the

product and the property from

damage.

Fig 3

Fig 4

7Remove the (5) tamper proof

screws from the unit in the

sequence illustrated in Figs 3-5

with the provided tamper proof

service tool, then remove the

fascia cover as illustrated in Fig 6.

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 8

Dyson AirbladeTM hand dryer

Connecting to the

Electrical Supply

CAUTION: Risk of electric

shock! Do not remove

casing or attempt repair

unless unit is being

serviced by qualified

service personnel.

If casing is removed or

handled improperly the

internal components of

the Dyson AirbladeTM may

cause harm or become

permanently damaged.

Connect to the electrical supply

using approved flexible or solid

conduit and electrical fittings.

Ensure that the flexible or solid

conduit and the electrical cable

is of sufficient length to make

the necessary connection to the

backplate and that the wires

are of sufficient length to reach

the terminal block.

Step 1.

Using a flat-head screwdriver,

pry the appropriate metal knock-

out from backplate in one of the

locations pictured in Fig 7.

Step 2.

Install electrical entrance fitting

into knock-out.

If mounting in knock-out 1:

Lay the unit flat on its back.

Remove the T-25 Torx screw at

the bottom of the PCB housing,

tilt the PCB housing up and pull

downward as illustrated in Fig 8.

Pull outward of gasket and turn

the PCB Housing clockwise

and set off to the side. Route

the incoming supply wires to

the terminal block and secure

them into the proper locations

as illustrated in Fig 9.

Installation Procedures

View from Back

Reconnect the PCB Housing

in the opposite order as it

was removed.

Proceed to step 3.

If mounting in knock-out 2:

Route the incoming supply

wires to the terminal block and

secure them into the proper

locations as illustrated in Fig 9.

Fig 8

Fig 7

Knock-outs

ENG

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 9

Dyson AirbladeTM hand dryer

Refitting Fascia &

Access Panels

Attach the front fascia panel

back on by latching the top lip

onto the middle fascia first and

then pivoting the fascia cover

downward until flush.

Install the bottom left and

right tamper proof screws back

into the machine using the

supplied tool.

Hanging unit

Hang the unit on the secured

mounting bracket as illustrated

in Fig 10.

Secure the unit through the 4

holes in the lower section of

the unit, illustrated in Fig 11.

Fig 10 Fig 11

Installation Procedures

Install the (2) tamper proof

screws back into the inner

section of the fascia panel.

Re-install the Access panel

and tamper proof screw.

ENG

Step 3.

Terminal block connections:

120 volt unit:

Secure the Line, Neutral and

Ground wires into the proper

terminal block locations.

Connecting to the

Electrical Supply cont.

Fig 9

L N

120v MODEL

18695_AB02_OP_MAN_US.qxd 29/8/07 14:42 Page 10

Andere Handbücher für airblade AB02

Inhaltsverzeichnis

Andere Dyson Trockner Handbücher

Dyson

Dyson AB09 Bedienungsanleitung

Dyson

Dyson AB09 Bedienungsanleitung

Dyson

Dyson Airblade AB06 Bedienungsanleitung

Dyson

Dyson AIRBLADE V Betriebsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson AB09 Bedienungsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson AB11 Bedienungsanleitung

Dyson

Dyson ab12 Bedienungsanleitung

Dyson

Dyson ab08 Bedienungsanleitung

Dyson

Dyson Airblade HU02 Bedienungsanleitung

Dyson

Dyson ab08 Bedienungsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson Airblade Tap Bedienungsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson Airblade Mk2 AB06 Bedienungsanleitung

Dyson

Dyson Airblade WD04 Bedienungsanleitung

Dyson

Dyson AIRBLADE V Bedienungsanleitung

Dyson

Dyson Airblade AB04 Bedienungsanleitung

Dyson

Dyson ab08 Bedienungsanleitung

Dyson

Dyson ab08 Bedienungsanleitung

Dyson

Dyson Airblade AB06 Bedienungsanleitung

Dyson

Dyson airblade AB02 Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung