E-Lins WAP100 series Bedienungsanleitung

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

E-Lins WAP100 Series AP

UserManual

E-Lins Technology Co., Ltd

ADDRESS: 1007A, MinTai Bld., Minkang Road, Minzhi Street, Bao'an District, ShenZhen,

518000, China

PHONE: +86 (755) 33231620



WEB: http://www.szelins.com

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

Contents

1 Product overview...................................................................................................................1

1.1 Introduction................................................................................................................... 1

1.2 Features and benefits................................................................................................... 2

1.3 Operation Modes and Connection Examples ............................................................. 3

1.3.1 Access Point and Access Point WDS Mode.................................................. 3

1.3.2 Access Point WDS Mode................................................................................ 3

1.3.3 Station Mode.................................................................................................... 3

1.3.4 StationWDS Mode.......................................................................................... 4

1.3.5 Router Mode .................................................................................................... 4

1.3.6 Repeater WDS Mode ...................................................................................... 5

2 Hardware installation............................................................................................................6

2.1 Setup requirements ...................................................................................................... 6

2.2 Hardware installation.................................................................................................... 6

2.3 Configure the IP Address ............................................................................................. 7

2.3.1 ForWindows 95/98/98SE/ME/NT .................................................................. 7

2.3.2 ForWindows XP/2000..................................................................................... 8

3 Access theWeb Interface ..................................................................................................10

3.1 Through our Utility uConfig ..................................................................................... 10

3.2 Access with a Web Browser....................................................................................... 12

4 Navigation...........................................................................................................................14

4.1 Main Menu................................................................................................................... 14

4.1.1 Main Menu Bar............................................................................................... 14

4.1.2 How to save changes.................................................................................... 14

4.2 Basic Network Tab...................................................................................................... 15

4.2.1 Network Modes: Bridging and Routing ........................................................ 15

4.2.2 LAN Setup...................................................................................................... 15

4.3 Basic Wireless Tab ..................................................................................................... 17

4.3.1 Basic Wireless Settings................................................................................. 17

4.3.2 Access Point Parameters Settings............................................................... 18

4.3.3 Station Parameters Settings......................................................................... 20

4.3.4 Wireless Security........................................................................................... 21

4.3.5 Virtual Access Point (VAP) ........................................................................... 25

4.4 AdvanceWireless Tab................................................................................................ 27

4.4.1 Long Range Parameters Setup.................................................................... 27

4.5 Advanced Network Tab.............................................................................................. 29

4.5.1 Spanning Tree Setup .................................................................................... 30

4.5.2 NAT Setup...................................................................................................... 30

4.5.3 Bandwidth Control ......................................................................................... 32

4.5.4 Firewall Setup................................................................................................ 32

4.6 Services Tab ............................................................................................................... 34

4.6.1 PingWatchdog .............................................................................................. 36

4.6.2 Auto-Reboot................................................................................................... 36

4.6.3 SNMP Setup .................................................................................................. 36

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

4.6.4 NTP Setup...................................................................................................... 37

4.6.5 Web HTTP Security....................................................................................... 37

4.6.6 Telnet Access Setup ..................................................................................... 37

4.6.7 SSH Access Setup ........................................................................................ 37

4.6.8 SystemLog Setup......................................................................................... 38

4.7 System Tab ................................................................................................................. 39

4.7.1 Firmware Upgrade......................................................................................... 39

4.7.2 Host Name ..................................................................................................... 39

4.7.3 Administrative and Read-only Account........................................................ 40

4.7.4 Enable Read-Only Account .......................................................................... 40

4.7.5 Configuration Management .......................................................................... 40

4.7.6 Device Maintenance...................................................................................... 41

4.8 Status Page................................................................................................................. 42

4.8.1 Status Reporting............................................................................................ 42

4.8.2 LAN Setting.................................................................................................... 42

4.8.3 Station Connection Status Info..................................................................... 43

Appendix I - Network .....................................................................................................................45

Appendix II Wireless with Router Mode....................................................................................48

Appendix III- Advanced Settings ..................................................................................................52

Appendix IV- Services...................................................................................................................54

Release Notes:

Release 1.0 This is the first Release

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

1 Product overview

1.1 Introduction

The high-performance Wireless Network Access Point (AP) is designed for enterprise and public

access applications. Embedded with the Atheros chipset, it boasts network robustness, stability and

wider network coverage. Based on 802.11n (Draft 2.0), the access point supports high-speed data

transmission of up to 300Mbps.

The access point is capable of operating in different modes, which makes it suitable for a wide variety

of wireless applications, including long-distance deployments.

Designed with dual polarization high gain antenna it offers a compact, rugged design for outdoor

installation and excellent performance.

Moreover, its integrated Power over Ethernet (PoE) allows the access point to be used in areas where

power outlets are not readily available.

To protect your security and privacy, the access point is armed with many enhanced and latest

wireless security features such as IEEE 802.11i standards, MAC Address Filtering, IEEE 802.1x

Authentication and 64/128-bit WEP (Wired Equivalent Privacy) to ensure privacy for the

heterogeneous mix of users within the same wireless network.

The access point also incorporates a unique set of advanced features such as: Virtual AP to deliver

multiple services; Long-Range parameter fine-tuning which provide the access point with the ability to

auto-calculate parameters such as slot time, ACK time-out and CTS time-out to achieve a longer

range.

1.2 Features and benefits

Point-to-Point & Point-to-MultiPoint Support

Point-to-Point and Point-to-MultiPoint communication between different buildings enables you to

bridge wireless clients that are kilometres apart while unifying the networks.

Virtual AP (Multiple SSID)

Virtual AP implements mSSID (Multi-SSID) This allows a single wireless card to be set up with

multiple virtual AP connections with different SSIDs or BSSID (Basic Service Set Identifier) and

security modes.

Highly Secured Wireless Network

The access point supports the highest available wireless security standard: IEEE802.11i compliant.

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

The access point also supports IEEE 802.1x for secure and centralized user-based authentication.

Wireless clients are thus required to authenticate through highly secure methods like EAP-TLS,

EAP-TTLS, and EAP-PEAP, in order to obtain access to the network.

uConfig Utility

The exclusive uConfig utility allows users to access the user-friendlyWeb configuration interface of

the access point without having to change the TCP/IP setup of the workstation.

HTTPS

The access point supports HTTPS (SSL) in addition to the standard HTTP. HTTPS (SSL) features

additional authentication and encryption for secure communication.

Telnet

Telnet allows a computer to remotely connect to the access point CLI (Command Line Interface)

for control and monitoring.

SSH

SSH (Secure Shell Host) establishes a secure host connection to the access point CLI for control

and monitoring.

1.3 Operation Modes and Connection Examples

1.3.1 Access Point and Access Point WDS Mode

The Access Point Mode is the default mode of the device. It enables the bridging of wireless clients to

wired network infrastructure and enables transparent access and communication with each other. The

illustration belowshows a typical resources sharing application example using this device. The wireless

users are able to access the file server connected to the switch, through the access point in Access

Point Mode.

1.3.2 Access Point WDS Mode

This ismode is generally use for point-to-point or point-to-multi-point connection.

It is mainly use with StationWDS to build the point and multi-point connections.

1.3.3 Station Mode

In Station mode the device acts as a wireless client.When connected to an access point, it creates a

network link between the Ethernet network connected at this client device, and the wireless Ethernet

network connected at the access point.

In this example the workgroup PCs on the ethernet network connected to the Station device can access

the printer across the wireless connection to the access point where the printer is connected.

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

1.3.4 Station WDS Mode

StationWDS mode is similar to Station mode. The difference is StationWDS must connect to access

point configured to Access Point WDS (or RootAP) mode.

StationWDS is mainly use for point-to point connection between 2 buildings or locations as far as

several kilometer away.

Point-to-Point Point-to-MultiPoint

Point to-Point Point to-MultiPoint

An access point setup as Access Point WDS (or

RootAP) and other as Station WDS (Transparent

Client).

An access point setup as Access Point WDS (or

RootAP) and several other devices as Station

WDS (or Transparent Client).

This mode is generally used for outdoor connections over long distances, or for indoor connections

between local networks.

1.3.5 Router Mode

In Router Mode, the device also operates as a router.

Either the wireless or Ethernet can be setup as WAN connection to a broadband modem. Wireless as

WAN is known as Station + Router mode (or Wireless Routing Client mode) and Ethernet as WAN

is known as AP + Router mode (or Gateway mode). Device supports several types of broadband

connections Static IP, Dynamic IP and PPPoE. For setup details refer to the respective section.

The illustration below shows the Ethernet port is setup as theWAN port and the wireless

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

connection as the LAN.

Station + Router connection example

Wireless is use to connect to the broadband.

Ethernet is the local network (LAN)

sharing the broadband connection.

AP + Router connection example

Ethernet is use to connect to the broadband.

Wireless is the local network (LAN)

sharing the broadband connection.

Broadband Internet Access Type:

Static IP Address

Use Static IP Address you have subscribed a fixed IP or range IP addresses fromyour ISP.

Dynamic IP Address

With Dynamic IP Address the device automatically request IP address frommodemor ISP.

PPP over Ethernet (PPPoE)

When using ADSL services provided by your ISP support PPPoE connection.

1.3.6 Repeater WDS Mode

Repeater WDS Mode to mainly to extend the wireless range and coverage of the wireless network

allowing access and communications over places generally difficult for wireless clients to connect to the

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

network.

In Repeater mode, the access point acts as a relay for network signals on the network by regenerating

the signals it receives, and retransmitting themto main network infrastructure.

Detailed information on the Repeater mode is available in the Repeater Setup

section.

** Note: Repeater WDS requires the access point to be setup in RootAP or

Access Point WDS mode to work.

2 Installation

2.1 Setup requirements

Before starting, please verify that the following is available:

CAT5/5e networking cable

At least 1 computer installed with a web browser and a wired or wireless network interface

adapter.

All network nodes installed with TCP/IP and properly configured IP address parameters.

2.2 Hardware installation

The access point can be powered using the 802.3af standard PoE Injector. This accessory supplies

operational power to the wireless access point via the Ethernet cable connection.

Step 1: Use an RJ45 Ethernet cable to connect one end of the cable to the Ethernet socket of the

Injector and the other end to one of the LAN ports of the accesspoint.

Warning:

When one port is used for PoE, the other port cannot connect to any other network device.

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

Step 2: Next, connect the RJ45 Ethernet cable attached to the standard PoE Injector to your PC s

Ethernet network adapter.

Once you have finished configuring your access point, you can connect thePoE Injector s RJ45

Ethernet cable to your network device, such as to a switchor hub.

2.3 Configure the IP Address

After setting up the hardware you need to assign an IP address to your PC so that it is in the same

subnet as the access point.

2.3.1 For Windows 95/98/98SE/ME/NT

Step 1:

From your desktop, right-click the Network Neighborhood icon and select Properties.

Step 2:

Select the network adapter that you are using, then right-click and select Properties.

Step 3:

Highlight TCP/IP and click on the Properties button.

E-Lins WAP100 Series OutdoorAP Quick Start 

E‐LinsTechnologyCo.,Limited

Tel:+86(755)33231620E‐mail:sales@szelins.comsales@e‐lins.comwww.szelins.com

Step 4:

Select the Specify an IP address radio button.

Set the IP address to 192.168.168.X and Subnet mask to 255.255.255.0, where X can be any number

from 2 to 254.

Step 5:

To verify that the IP address has been correctly assigned to your PC, go to the Start menu, select Run,

and enter the command: winipcfg.

Select the Ethernet adapter fromthe drop-down list and click OK.

PC is now setup with proper IP address to communicate with the access point.

2.3.2 For Windows XP/2000

Step 1:

Go to your desktop, right-click on the My Network Places icon and select Properties.

Step 2:

Right-click the network adapter icon and select Properties.

Step 3:

Highlight Internet Protocol (TCP/IP) and click on the Properties button.

Inhaltsverzeichnis

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung