EASYPRINT Compact CM Bedienerhandbuch
Compact CM
Compact IM
Easyprint
User Documentation
EPT033789 Issue 2 February 2018 1
CONTENTS
REGULATION...................................................................................................... 3
FCC Notice ...................................................................................................... 3
European EMC Statement............................................................................... 3
HEALTH AND SAFETY........................................................................................ 4
Symbols........................................................................................................... 4
Warning Notices .............................................................................................. 5
Caution Notices ............................................................................................... 5
INTRODUCTION ................................................................................................. 7
General ............................................................................................................ 7
Description ............................................................................................ 7
Intended Use ......................................................................................... 7
System Specification....................................................................................... 8
Compact Touchscreen.......................................................................... 8
Printer Specification .............................................................................. 8
Power Supply Unit................................................................................. 11
Optional Touchscreen ........................................................................... 11
INSTALLATION ................................................................................................... 12
Mechanical Installation Requirements............................................................. 12
Brackets .......................................................................................................... 12
Window bracket (for IM and CM versions)............................................ 12
Web positioning module ....................................................................... 12
Labeller bracket (IM only) ...................................................................... 12
Mounting the Printer in the Bracket System.................................................... 13
Connectivity..................................................................................................... 14
Set Up Printer - Final Steps............................................................................. 15
Calibrating the Printer............................................................................ 15
Optimising the Print Head ..................................................................... 15
Print Trigger........................................................................................... 17
Test Print, Align and Calibrate............................................................... 17
2 EPT033789 Issue 2 February 2018
OPERATION........................................................................................................ 18
Start-Up........................................................................................................... 18
Shut Down....................................................................................................... 19
Disconnect Compact Touchscreen /
Touchscreen from Printer...................................................................... 19
Printer Shut Down ................................................................................. 19
Screen Functions............................................................................................. 19
General .................................................................................................. 19
Editor Screen................................................................................................... 20
New Message.................................................................................................. 21
Add........................................................................................................ 22
Save Message....................................................................................... 22
Selecting an Existing Message........................................................................ 23
Changing an Existing Message............................................................. 23
Global Print Settings........................................................................................ 24
Quality ................................................................................................... 24
Economy ............................................................................................... 25
Position.................................................................................................. 26
Saved With Message............................................................................. 26
MAINTENANCE................................................................................................... 27
Common Errors and Acknowledgement ......................................................... 27
Ribbon Breaks....................................................................................... 29
Replacing the Ribbon ...................................................................................... 30
Setting the Ribbon Type........................................................................ 30
Ribbon Threading Procedure ................................................................ 31
Cleaning the Print Head .................................................................................. 33
Cleaning the Capstan Roller............................................................................ 34
Maintenance Schedule .................................................................................... 35
EPT033789 Issue 2 February 2018 3
REGULATION
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
European EMC Statement
This product may cause interference if used in residential areas. Such use must be avoided
unless the user takes special measures to reduce electromagnetic emissions to prevent
interference to the reception of radio and television broadcasts.
4 EPT033789 Issue 2 February 2018
HEALTH AND SAFETY
Notes: (1) Please read the entire Health and Safety section in your Product Manual (Part
No. EPT033612) before operating the printer.
(2) Unless stated otherwise, information provided is applicable to all printer
variants.
The printer and its component parts must only be used for the purpose for which they were
sold, and for which they are designed and constructed. No parts may be used for other
functions.
Read the Safety Data Sheet (SDS) for Cleaning Fluid (Part No. WJ-111).
Read the following important notices before using the printer. The hazard information is
prioritised into warning and caution notices.
Symbols
The following symbols are used in this manual. Where they appear next to a procedure or
instruction, they have the significance and importance of written warnings and cautions.
Eye protection must be worn.
Protective clothing must be worn. Use adequate protective
gloves. Consult the relevant Safety Data Sheet (SDS).
Disconnect before carrying out maintenance or repair.
Only trained personnel should carry out this procedure.
EPT033789 Issue 2 February 2018 5
Warning Notices
Warning notices denote a potential hazard to the health and safety of users. These notices
clearly state the nature of respective hazard and the means by which it can be avoided.
WARNINGS: (1) Only trained and authorised personnel may carry out maintenance
work. Observe all statutory electrical safety codes and practices.
Risk of electric shock, disconnect the printer from the mains
electrical supply before removing the cover or attempting any
service or repair activity.
(2) The heating element and surrounding area become very hot during
use. To avoid the risk of burns, never touch the heating element
area of the print head.
(3) Cleaning fluid contains organic solvents. Always wear suitable
PPE (goggles and clothes) to avoid contact with the eyes and skin.
Avoid inhalation of the vapour. Do not smoke in the vicinity of
solvents.
(4) Replace ribbons with care to avoid cutting hands or fingers.
(5) Keep clear of the print head whilst the printer is powered on, due
to risk of injury from moving parts.
(6) Replaceable batteries should only be replaced using batteries of
the correct specified type and rating. Failure to do so may result in
an explosion hazard. Used batteries should be disposed of
according to the battery manufacturer’s instructions.
(7) To ensure continued protection against the risk of fire, replace
fuses with the specified type and rating only.
(8) To avoid the possibility of electric shock hazard and damage to
equipment, do not fit or remove any connector (except USB) on the
printer while the printer is switched on.
(9) There is a danger of electrical shocks from the electrical outlet. All
electronic checks must be performed by qualified personnel.
Caution Notices
Caution notices denote a risk to equipment damage. These notices clearly state the nature of
the hazard and the means by which it can be avoided.
CAUTIONS: (1) Changing the print head without setting the new resistance value may
cause severe damage to the print head.
(2) To avoid damage to the cables or equipment, ensure that the cables
are routed clear from any moving parts.
(3) To avoid damage to the equipment, do not exceed the supply voltage
stated in the manual.
(4) To avoid damage to the printer components, use only soft brushes and
lint-free cloths. For cleaning, always use Cleaning Pens (Part No.
VPR0223), Cleaning Fluid (Part No. WJ-111) and Print Head Cleaning
6 EPT033789 Issue 2 February 2018
Wipes (Part No. MT25215). Do not use high pressure air, cotton waste,
abrasive materials, metallic objects or degreasing cleaning fluids (e.g.,
Benzene, acetone).
(5) To avoid the risk of damage to the print head use only Easyprint spares,
parts and consumables.
(6) Do not run the printer without ribbon material, as this may damage the
print head.
(7) Do not expose the printer or controller to any water
EPT033789 Issue 2 February 2018 7
INTRODUCTION
General
This document contains basic operation instructions for the Easyprint Compact CM and
Compact IM printers.
For further information, refer to Product Manual (Part No. EPT033612).
Description
The Easyprint Compact is an industrial Thermal Transfer Overprinter (TTO). It consists of a
rectangular printer unit which contains a heated print head and thermal ribbon. The printer
can be controlled through an optional Touchscreen, Compact Touchscreen or from a
networked PC.
Printing is achieved by placing a thermal ribbon between a heated printhead and the
substrate to be marked. Heat from the printhead is passed through the ribbon, causing ink to
melt and be released from its underside. The ink adheres to the substrate and then cools
rapidly, resulting in a permanent print.
Intended Use
The Easyprint Compact is intended to print variable data, bar codes and images onto flexible
packaging films and labels.
The Compact CM and Compact IM are entry level, compact TTO printers with a 32mm wide
print head. The maximum ribbon length is 770m which gives an effective length of 960m when
economy mode is used.
Continuous Mode (CM).
The Compact CM is used when printing on a substrate which moves continuously.
Intermittent Mode (IM).
The Compact IM is used when printing on a stationary substrate which only moves between
printing.
8 EPT033789 Issue 2 February 2018
System Specification
Compact Touchscreen
Printer Specification
Type 5.7 inch, full colour Compact Touchscreen
(640x480 resolution), handheld, with docking
station.
Compact
Touchscreen
Dimensions (mm)
170(W) x 127.9(H) x 33.7(D)
Weight (kg) 0.385kg
Connectivity USB, Ethernet, (Mini USB for power / data
connection to printer)
Network Interface Ethernet 10/100 base TX
Accessories Wall brackets
Operating
environment
5 - 40°C
Humidity 20 - 80 % RH non-condensing
Printing Mode For IM printers: Intermittent
For CM printers: Continuous
Left Hand / Right
Hand
Both options available (convertible with no
extra parts in 15 minutes)
Print Resolution 300 DPI
For IM printers:
Maximum Print Area
32mm x 45mm
For CM printers:
Maximum print area
32mm x 100mm
For IM printers:
Print Speed (max)
400mm/s
For CM printers:
Speed Range
10mm/s - 550mm/s
Print repeat rate
(max)
4 prints/s (with a 10mm long print)
Ribbon drive
technology
i-Tech Ribbon Drive with unique dancing arm
tension control
EPT033789 Issue 2 February 2018 9
Max ribbon length 770m (up to 960m effective length with
Economy mode)
Ribbon save modes
Economy mode: Variable up to 20% with no reduction in print
resolution
Retraction mode: Less than 1mm gap between prints
Column mode: For CM printers:
15mm max printed ribbon per print.
For IM printers:
45mm max printed ribbon per print.
Print features Date code format, offsets, shift codes, serial
number generation
Fonts Most TrueType fonts
Controller / hardware
interface options
No dedicated controller required. Hardware
interface options: Easyprint Compact
Touchscreen (via USB cable- hot swappable),
Shared Compact Touchscreen (via Ethernet
cable or network), PC-based interface (via
Ethernet cable or network)
Connectivity Ethernet / USB x 2 / mini USB (service)
CAUTION: The ethernet socket includes Power over Ethernet
output.
Inputs Print Go, Encoder
Outputs Error, Ready, Ribbon Low, Spare (volt-free
contacts)
Special features Master / slave, password, Fast Mode
Label creation Onboard or via EasyDesign or QuickDesgin
Electrical
requirements
90V - 264V AC 50/60Hz, OR 24V d.c. (+/- 2%)
at 5A (if direct)
Dimensions:
Width 218mm
Height 160mm
Depth 148.5mm
Weight 5.6kg
Temperature
requirements
5°C to 40°C
Andere Handbücher für Compact CM
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere EASYPRINT Drucker Handbücher
