Eaton xStorage Home Bedienungsanleitung
xStorage Home User Interface Manual
For 4.2 kWh, 6 kWh and 10 kWh systems capacity
This document is intended for Eaton
certified installers.
xStorage Home
2
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
Content overview
1 Introduction.............................................................................................................................................3
Before you start ...................................................................................................................................................... 3
Technical disclaimer ................................................................................................................................................ 3
Legal entity ............................................................................................................................................................. 3
2 Good to know ..........................................................................................................................................4
3 Commissioning xStorage Home ...........................................................................................................4
3.1 Starting the commissioning of xStorage Home............................................................................................... 4
3.2 Step 1: Network settings ................................................................................................................................. 5
3.3 Step 2: Date & Time Conguration .................................................................................................................. 7
3.4 Step 3: Topology............................................................................................................................................... 8
3.5 Step 4: Finish ................................................................................................................................................... 9
3.6 Recommissioning the xStorage Home unit ....................................................................................................10
4 Local and Cloud UI interface................................................................................................................ 11
4.1 How to use the local UI ..................................................................................................................................11
4.2 How to connect to xStorage Cloud.................................................................................................................12
5 User role-based access authorization ................................................................................................ 13
6 How to update xStorage Home hosted on the Cloud web portal ..................................................14
7 How to update xStorage Home from the local user interface ........................................................15
8 How to update the user interface on units running with the previous user interface................. 17
3
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
1. Introduction
Thank you for installing the xStorage Home system
This manual provides Eaton certied installers with instructions on how to do the commissioning and the onboarding of xStorage
Home using the xStorage Home user interface. This manual is complementary to the xStorage Home installation and user
manuals.
This manual also details the onboarding process and the update process of the xStorage Home unit. This update process can be
done directly on the local web portal or through the Cloud web portal if the unit is connected to the Cloud (xstoragehome.com).
Before you start
This manual contains important instructions that must be followed during the installation, operation and maintenance
of the xStorage Home system. All instructions must be read before installing and operating the equipment. This manual
should be retained for future reference.
Please note that the xStorage Home system must only be installed by Eaton certied personnel, i.e. an Eaton technical
support representative or an Eaton certied installer. There are no user serviceable parts inside the xStorage Home
system. Failure to observe the above will void the guarantee provided and Eaton cannot be held legally accountable.
This product is intended for residential application only. The contents of this manual are the copyright of the publisher and
may not be reproduced (even in extracts) without the prior written approval of Eaton Corporation. While every care has
been taken to ensure the accuracy of the information contained in this manual, Eaton assumes no liability for any error
or omission. Eaton reserves the right to modify the designs of its products. The unauthorized copying and lending of this
manual is prohibited.
Technical disclaimer
In line with our goal to continuously improve the products and the customer service we provide, all specications
contained in this document are subject to change with due notice. All drawings, descriptions or illustrations contained
in this document serve to provide a clear overview and/or technical explanation of the present product and its various
components and accessories.
Legal entity
Eaton Energy Storage
Eaton Industries manufacturing GmbH
Address: Place de la Gare 2
1345 Le Lieu
SWITZERLAND
Web: www.eaton.com/xstorage
4
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
2. Good to know
3. Commissioning xStorage Home
To download the latest technical documentation, such as the user manual, the safety documentation and other relevant updates,
visit our website www.eaton.com/xstorage. Please note that in order to improve our customer experience we are constantly
updating and enhancing the relevant technical and marketing materials.
3.1 Starting the commissioning of xStorage Home
• Access the local web user interface (UI) by entering https://<unit_IP> on your browser. The failover IP Address is 192.168.2.254.
• Check that the PC or your device is below the subnet of xStorage Home. See section 4.1 for further details.
• Once you’ve typed the IP address, the browser displays a warning message. Continuing the procedure will not cause any
harms to your computer, tablet or smartphone.
• To be able to proceed, click on ‘Advanced’ to expand the Advanced section from the warning page and click on ‘Continue’ to be
directed to the local xStorage Home portal.
• As an Eaton certified installer, click on “I’m a technician” to start the commissioning (see Figure 1).
Only Eaton certied installers can install, congure and commission the xStorage Home system. Once the commissioning is
fully completed, the xStorage Home system is ready to be used by the end-user and the end-user can decide if he/she wants to
switch between Cloud and Local mode at any time.
As an Eaton certied installer, you must have an email address registered in the Eaton database.
Use this registered email address when you sign in as a technician.
It is possible to use multiple browsers except Internet Explorer which is not supported.
Figure 1: Welcome pages of the local web user interface
5
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
Username Default Password Inverter Serial Number Installer email
user user N/A N/A
Default credentials for the end-user and Eaton certied installers are shown in Table 1.
Table 1: Default credentials for the end-users and Eaton certified installers
• You can start the commissioning connected to the home internet network or the local router, via WiFi or an ethernet cable.
• To connect via the ethernet cable, check that the xStorage Home system is listed below the right subnet as shown in Figure 9.
• To connect via the WiFi local access point, use the following default SSID, password and IP address:
• SSID: xstorage
• Password: P4svFJA9
• IP address: 192.168.3.99
3.2 Step 1: Network settings
• Click on ‘Network settings’.
• Fill in the form to proceed with the configuration of the communication card and the onboarding of the xStorage Home system.
• If you use an ethernet cable, it is recommended to use DHCP (see Figure 2).
Figure 2: Network settings connection via an ethernet cable with DHCP
6
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
If you use a static address, you can edit the IP address as shown in Figure 3.
Figure 3: Network settings connection via an ethernet cable using a static address
You can also connect to the home internet network via WiFi as shown in Figure 4.
Figure 4: Network settings connection via WiFi
• If the WiFi or the ethernet cable is correctly configured, a message mentions that the assigned IP address is displayed.
• Otherwise, an error message details the issue that prevented the communication card to connect to the network.
Once the network congurations are completed, press “Next”, and move to the Date & Time Conguration page.
At this stage, the application tests the network connectivity. Therefore, it navigates to the Date & Time page only if the network
is correctly congured.
7
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
Figure 5: Date & Time configuration page
• It is mandatory to set up a date and time conguration. Both manual and automatic setups are available.
• If you use a NTP server, ensure that the internet connection is well established.
• Select the right date and time, then the country, city and time zone where the end-user is located as shown in Figure 5.
• Once the conguration is nalized, press “Next” to move to the Topology step.
3.3 Step 2: Date & Time Configuration
8
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
As an Eaton certied installer, you need to congure the topology of the installation at the end user’s home in order to nalize the
commissioning process. You can nd the details of this procedure in the xStorage Home installation manual and power meters
manual available on eaton.com/xstorage. Depending on the installation at the end user’s home, you may need to congure the
following:
• Power meter 1. Please select the meter from the drop-down menu;
• Power meter 2. Please select the meter from the drop-down menu;
• Photovoltaic panels.
In the example shown in Figure 6, the power meter Sfere DDS1946-DS is set at both Power meter 1 and Power meter 2 and
photovoltaic panels are installed and connected to xStorage Home.
3.4 Step 3: Topology
Figure 6: Example of a topology configuration with xStorage Home
For the power meter Eastron SDM 120CT-Modbus, the procedure starts from Power meter 2 as indicated in the xStorage Home
Power Meters manual that you can download on eaton.com/xstorage.
9
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
3.5 Step 4: Finish
Figure 7: Final page
1. Once you’ve completed the final stage of the setup process detailed in the xStorage Home installation manual, choose
between connecting the unit to the Cloud or continue to use it in local mode.
2. As the Eaton certified installer, go to the Home page of the xStorage Home portal and insert the end-user name and email
address so that the end-user takes ownership of the unit as shown in Figure 7. The end-user is now ready to claim the
ownership of the unit.
3. Below is the procedure for the end user to claim the ownership of the unit.
• The end-user needs to go to the log-in page on https://xstoragehome.com/ and sign-up with the end-user email address
already registered by the installer
• Once the sign-up is completed, an email is sent to the end user mailbox to finalize the account creation and claim ownership
of the xStorage Home system. Ensure that the end-user registers the address noreply@xstoragehome.com in his/her
contacts as the email may end up in the end-user spam box otherwise.
• The email contains a link that enables the end-user to finalize the claim process.
• At this stage, the xStorage Home system is onboarded, and the end-user can access it via https://xstoragehome.com/.
10
XSTORAGE HOME USER INTERFACE MANUAL July 2019 www.eaton.com
3.6 Recommissioning the xStorage Home unit
An Eaton certied installer can always reinstall the xStorage Home system. From the local UI click on “Reinstall unit” in the
menu, then click on the ‘Reinstall xStorage unit’ button as shown in Figure 8. In this case the commissioning process will start
from the beginning and the Eaton certied installer will be redirected to the Network settings page. This option is only available
for Eaton customer support representatives and Eaton certied installers.
Figure 8: Reinstall the xStorage Home system
Andere Handbücher für xStorage Home
1
Inhaltsverzeichnis
Andere Eaton Steuerungssystem Handbücher
Eaton
Eaton COOPER POWER SERIES Bedienungsanleitung
Eaton
Eaton Rapid Link RAMO5 Bedienungsanleitung
Eaton
Eaton COOPER POWER SERIES Bedienungsanleitung
Eaton
Eaton FLX Lighting Console Bedienungsanleitung
Eaton
Eaton iLumin Plus Benutzerhandbuch
Eaton
Eaton SVS/12 Bedienungsanleitung
Eaton
Eaton Crouse-Hinds GHG 61 R Series Bedienungsanleitung
Eaton
Eaton CCS 5 Bedienungsanleitung
Eaton
Eaton Vickers FG-3 10 Series Bedienungsanleitung
Eaton
Eaton SC200 Betriebsanleitung
