Eaton A201 Handbuch

INSTRUCTION LEAFLET IL17053

Effective MAY 2011

Supersedes JUNE 1989

Instructions for A201, A211, A251

Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

THE CONTACTOR

A201 contactors are designed for the control of inductive or non-

inductive loads at voltages between 120 and 600, AC. The units are

suitable for mounting on either steel or insulated panels. All parts are

front removable.Contactors should be protected against short circuits by

branch circuit protective devices selected in accordance with the National

Electrical Code (NEC).

This motor controller is suitable for use on a circuit capable of delivering

not more than the current (rms symmetrical amperes) shown below in

circuits rated not more than the voltage shown in Table I.

INSTALLATION

This industrial type control is designed to be installed, operated, and

maintained by adequately trained workmen. These instructions do not

cover all details, variations, or combinations of the equipment, its storage,

delivery, installation, check out, safe operation, or maintenance. Care

must be exercised to comply with local, state, and national regulations,

as well as safety practices, for this type of equipment. See page 5 for

mounting dimensions and terminal information.

Mount the contactor on a vertical surface with the line terminals above

the load terminals. Once installed, the assembly should be checked

to ensure proper operation of the basic contactor mechanism and

accessory devices before power is applied.

The following list and the MAINTENANCE

instructions should be used as a guide:

a) The crossbar and springs must operate freely.

b) Auxiliary contacts and mechanical interlocks

must be properly installed and adjusted.

c) The proper operating coil must be installed and

properly connected.

d) The crossbar must be in position. The contactor

will not operate if the crossbar is rotated forward,

out of position.

e) The arc box must be in place. The contactor

must never be operated in a power circuit unless

the arc box is securely bolted in place.

f) The main contacts must have overtraveI and

spring force and move freely.

2EATON CORPORATION www.eaton.com

INSTRUCTION LEAFLET IL170053

Effective May 2011

Instructions for A201, A211, A251 Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

INSTRUCTION LEAFLET IL17053

Effective May 2011

EATON CORPORATION www.eaton.com

Instructions for A201, A211, A251 Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

4EATON CORPORATION www.eaton.com

INSTRUCTION LEAFLET IL170053

Effective May 2011

Instructions for A201, A211, A251 Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

INSTRUCTION LEAFLET IL17053

Effective May 2011

EATON CORPORATION www.eaton.com

Instructions for A201, A211, A251 Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL17053/ 001

May 2011

Eaton is a registered trademark of Eaton

Corporation.

All other trademarks are property of their

respective owners.

INSTRUCTION LEAFLET IL17053

Effective May 2011

Instructions for A201, A211, A251 Size 6, 2 and 3 Pole Contactors,

Nonreversing or Reversing

Dieses Handbuch passt für folgende Modelle

Andere Eaton Controller Handbücher

Eaton

Eaton SC100 Bedienungsanleitung

Eaton

Eaton CGLine+ Web-Controller Bedienungsanleitung

Eaton

Eaton Cutler-Hammer FD100 Bedienungsanleitung

Eaton

Eaton EMS2 SWD Series Bedienungsanleitung

Eaton

Eaton DILMT40 Handbuch

Eaton

Eaton DS7 Series Bedienungsanleitung

Eaton

Eaton ELC-CODNET Bedienungsanleitung

Eaton

Eaton ELC2 Series Bedienungsanleitung

Eaton

Eaton ELCM Series Bedienungsanleitung

Eaton

Eaton CDAE-01/04 Bedienungsanleitung

Eaton

Eaton RTC-100 Bedienungsanleitung

Eaton

Eaton CDAU-01/04 Bedienungsanleitung

Eaton

Eaton Cutler-Hammer W200 Bedienungsanleitung

Eaton

Eaton xComfort Room Controller Touch Bedienungsanleitung

Eaton

Eaton Vickers SMC20 Bedienungsanleitung

Eaton

Eaton ATC-600 Programmierhandbuch

Eaton

Eaton Cutler-Hammer Pow-R-Command JCI-100 Handbuch

Eaton

Eaton Cutler-Hammer S701X25N3BP Handbuch

Eaton

Eaton Cutler-Hammer LMR Bedienungsanleitung

Eaton

Eaton MVX9000 Series Bedienungsanleitung

Eaton

Eaton S811 Bedienungsanleitung

Eaton

Eaton XV-102 Series Bedienungsanleitung

Eaton

Eaton HFX Series Bedienungsanleitung

Eaton

Eaton ELCM Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch