Eaton ELCB Series Bedienungsanleitung

Eaton Logic Controller

ELCB Controllers

INSTRUCTION SHEET

[Applicable Controllers]

ELCB-PB10NNDR/T

ELCB-PB14NNDR/T

ELCB-PB20NNDR/T

ELCB-PB30NNDR/T

ELCB-PB40NNDR/T

2010-12-10

5011699201-PBB1

IL05001005E

002-1310020-02

- 1 -

Thank you for choosing this Eaton Logic Controller (ELC) series has

controllers with 10 to 40 embedded I/O points. To ensure proper installation,

operation and maintenance, please read this instruction sheet carefully

before installing ELCB-PB.

This instruction sheet provides only information on the electrical

specification, general functions, installation and wiring. It should be read

and understood before attempting to install or use the unit.

Further information can be found in the ELC series Programming

Manual.

These are OPEN TYPE controllers and therefore should be installed in

an enclosure free of airborne dust, humidity, electric shock and vibration.

Your application may require that the enclosure be locked to prevent

non-maintenance staff from operating the controller (e.g. key or specific

tools that are required for opening the enclosure) in cases where danger

and damage to equipment or personnel may occur.

DO NOT connect AC power to any of the DC I/O terminals; serious

damage may occur. Check all wiring before switching on power.

Ensure that the ground terminal is correctly grounded in order to

prevent electromagnetic interference.

This manual is subject to change without notice.

Product Profile

+24V24 G S/S X0 X1 X2 X3 X4 X5 X6 X7

LNC0 Y0 Y1 Y2 Y3 C1 Y4 Y5

Panel mounting

hole

I/O terminal

numbers

DC sensor

power supply

output I/O point

indicators

COM1 Comm.

(RS-232C)port

DIN rail mounting

slot (35mm)

Panel mounting

hole

I/O terminals

DIN rail clip

POWER, RUN & ERROR

indicators

I/O terminal

numbers

AC power

supply input

COM2 Comm.

(RS-485)port

D+ D- SG

Y6 Y7

Module name

CO M2

CO M1

X1 0 X11 X12

Note1: The above figure is the layout of ELCB-PB20NNDR.

Dimension

ELCB-

PB10

NNDR/T

PB14

NNDR/T

PB20

NNDR/T

PB30

NNDR/T

PB40

NNDR/T

150

164

141

155

- 2 -

48.5

107.6

Unit: mm

Electrical Specifications

ELCB-

Item

PB10

NNDR/T

PB14

NNDR/T

PB20

NNDR/T

PB30

NNDR/T

PB40

NNDR/T

Power supply

voltage

100 ~ 240VAC (-15% ~ 10%), 50/60Hz 5%

Operation

ELCB-PB starts to run when the power supply rises to 95 ~ 100VAC

and stops when the power supply drops to 70VAC. It continues to

run for 10ms after the power supply is cut off.

Power supply

fuse

2A/250VAC

Power

consumption

12VA

15.6VA

DC24V current

output

200mA

300mA

Power supply

protection

DC24V output short circuit protection

Voltage

withstand

1,500VAC (Primary-secondary), 1,500VAC (Primary-PE), 500VAC

(Secondary-PE)

Insulation

resistance

> 5MΩat 500VDC (between all I/O points and earth)

Noise immunity

ESD: 8KV Air Discharge

EFT: Power Line: 2KV, Digital I/O: 1KV,Analog & Communication

I/O: 250V

RS: 26MHz ~ 1GHz, 10V/m

Grounding

The diameter of grounding wire shall not be less than that of L, N

terminal of the power supply. Make sure every ELCB in your system

is properly grounded.

Operation/

storage

Operation: 0°C~55°C (temperature), 50~95% (humidity), pollution

degree 2

Storage: -25°C~70°C (temperature), 5~95% (humidity)

Vibration/shock

resistance

IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC 68-2-27

(TEST Ea)

Weight (R/T)

192g

180g

202g

185g

255g

230g

280g

245g

340g

300g

- 3 -

Input Points

Input No.

X0, X1

X2 ~ #1

Input point type

Digital input

Input type

DC (SINK or SOURCE)

Input current

24VDC, 5mA

Action level

Off → On

> 15VDC

On → Off

< 5VDC

Response

time

Off → On

25us

50us

On → Off

10us

20us

Filter time

Adjustable within 0 ~ 20ms in D1020 (Default: 10ms)

Output Points

Output point type

Relay-R

Transistor-T

Voltage specification

< 240VAC, 30VDC

5 ~ 30VDC #2

Maximum

load

Resistive

2A/1 point (5A/COM)

0.5A/1 point (2A/COM)

Inductive

12W (24VDC)

Lamp

20WDC/100WAC

2W(24VDC)

Response

time

Off → On

Approx. 10 ms

30us

On → Off

350us

#1: Please refer to “I/O Terminal Layout”for the maximum number of in puts and outputs

on each controller.

#2: UP, ZP must work with external auxiliary power supply 24VDC (-15% ~ +20%), rated

consumption approx. 1mA/point.

#3: See life curves (below)

Contact

Current(A)

0.5

0.1 0.2

0.3 0.7 1 2

200

300

500

100

1000

2000

3000

Operation(X10 )

120VAC Resistive

30VDC Inductive(t=7ms)

240VAC Inductive(cos 0.4)ψ=

120VAC Inductive(cos =0.4)ψ

30VDC

Inductive

(t=40ms)

Installation

Please install your controller in an enclosure with sufficient space around it

to allow proper ventilation, as shown in the figure.

DIN Rail Mounting: When mounting the

ELCB to 35mm DIN rail, be sure to use the

retaining clip to stop any side-to-side

movement of the ELCB and reduce the

chance of wires becoming loose. The

retaining clip is at the bottom of the ELCB.

- 4 -

To secure your controller to the DIN rail, pull the clip down, place it onto

the rail and gently push the clip up. To remove the ELCB, pull the

retaining clip down with a flat screwdriver and gently remove the ELCB

from DIN rail.

Wiring

1. Use 12-24 AWG single-core bare wire or multi-core (stranded) wire for

the I/O wiring. The ELCB terminal screws should be tightened to 3.80

kg-cm (3.30 in-lbs) using 60/75°C copper conductor only.

2. DO NOT wire empty terminals. DO NOT place input signal wires and

power wires in the same wiring circuit.

3. DO NOT drop tiny metallic conductors into the ELCB while installing the

controller or other equipment.

Power Supply

The input power supply for the ELCB-PB controller isAC. When operating

ELCB-PB, please note the following points:

1. The range of the input voltage should be 100 ~ 240VAC. The power

supply should be connected to L and N terminals. Please note: wiring

110VAC or 220VAC to a +24V output terminal or to digital inputs will

result in serious damage to the ELCB.

2. Use 1.6mm wire (or larger) for the grounding ELCB.

3. Apower loss for less than 10ms will not affect the operation of the ELCB.

However, longer power loss or a sustained drop of power supply voltage

will stop the running of the ELCB, and all outputs will turn “OFF”. When

proper power is restored, the ELCB will resume operation. (Please keep

this in mind when you use latched auxiliary relays and registers in your

ELCB program.)

4. Please refer to the electrical specification table for the maximum output

of the +24V power supply output terminal for each controller. DO NOT

connect other external power supplies to this terminal. Every input point

requires 5 to 7mA to drive when powered by rated voltage 24V to 30V

(i.e. 16 input points will require 80 to 112mA to drive). The +24V input on

ELCB-PB is only for digital input points; other external loads are not

supported.

Safety Wiring

In an ELCB control system, many devices are controlled at the same time,

and actions of any device could influence another device, i.e. breakdown of

any device may cause the breakdown of the entire control system.

Therefore, we suggest you wire a protection circuit at the power supply

input terminal. See the figure below.

- 5 -

○

AC power supply:100 ~ 240VAC, 50/60Hz

○

Breaker

○

Emergency stop: This button cuts off the system power supply when accidental

emergency takes place.

○

Power indicator

○

AC power supply load

○

Power supply circuit protection fuse (2A)

○

ELCB (main processing unit)

○

DC power supply output: 24VDC

I/O Point Wiring

There are 2 types of DC inputs, SINK and SOURCE. (See the example

below. For detailed wiring configuration, please refer to the specification of

each controller.)

DC Signal IN –SINK mode

Input point loop equivalent circuit

DC Signal IN –SOURCE mode

Input point loop equivalent circuit

24G

+24V

S/S

+24V

24G

S/S

Relay (R) output circuit wiring

- 6 -

○

DC power supply

○

Emergency stop: Use an external switch

○

Fuse: Use 5 to 10A fuse at the shared terminal of output contacts to protect the

output circuit

○

Transient voltage suppressor: To extend the life span of relay contacts.

1.Diode suppression of DC loads: Used for smaller loads.

2.Diode + Zener suppression of DC load: Used with larger loads, and for rapidly

switching applications.

○

Incandescent light (resistive load)

○

AC power supply

○

Mutually exclusive output: For example, Y4 and Y5 control the forward running and

reverse running of the motor, forming an interlock for the external circuit, together

with the ELCB internal program, to ensure safe operation in case of any unexpected

errors.

○

Neon indicator

○

Suppressor: To reduce the interference on AC load (Figure 10)

Transistor (T) output circuit wiring

- 7 -

○

DC power supply

○

Emergency stop

○

Circuit protection fuse

○

The output of the transistor module is “open collector”. If Y0/Y1 is set to pulse

output, the output current has to be 0.05 ~ 0.5A to ensure normal operation of the

output.

1. Diode suppression: Used with smaller loads.

2. Diode + Zener suppression: Used with larger loads, and for rapidly switching

applications.

○

Mutually exclusive output: For example, Y3 and Y4 control the forward running and

reverse running of the motor, forming an interlock for the external circuit, together

with the ELCB internal program, to ensure safe operation in case of any unexpected

errors.

RS-485 Wiring

D+ D- SG D+ D- SG SG D+ D-

1 2 2

○

Master node

○

Slave node

○

Terminal resistor

○

Shielded cable

Note: 1. Terminal resistors are suggested to be connected to the master, and the last

slave, with resistor value of 120.

2. To ensure communication quality, please wire using double shielded twisted

pair cable (20AWG).

3. When voltage drop occurs between the internal ground references of two

systems, connect the systems with Signal Ground point (SG) for achieving

equal potential between systems so that a stable communication can be

obtained.

- 8 -

I/O terminal layout

ELCB-PB10NNDR/T

Y3Y2Y1Y0C0

X5X4X3X2X1X0

24G+24V

ELCB-PB10NNDR (6DI-DC/4DO-R)

S/S D+ SGD-

Y2Y1Y0ZPUP

X5X4X3X2X1X0

24G+24V

ELCB-PB10NNDT (6DI-DC/4DO-T)

S/S

D+ SGD-

ELCB-PB14NNDR/T

Y3Y2Y1Y0C0

X5X4X3X2X1X0

24G+24V

ELCB-PB14NNDR (8DI-DC/6DO-R)

S/S

X7X6

Y5Y4

D+ SGD-

Y2Y1Y0ZPUP

X5X4X3X2X1X0

24G+24V

ELCB-PB14NNDT (8DI-DC/6DO-T)

S/S

X7X6

Y5Y4

D+ SGD-

ELCB-PB20NNDR

Y3Y2Y1Y0C0

X5X4X3X2X1X0

24G+24V

ELCB-PB20NNDR (12DI-DC/8DO-R)

S/S

X7X6

Y5Y4

X11X10 X12

Y6 Y7

D+X13 SGD-

Y2Y1Y0ZP0UP0

X5X4X3X2X1X0

24G+24V

ELCB-PB20NNDT (12DI-DC/8DO-T)

S/S

X7X6

Y5Y4

X11X10 X12

Y6 Y7

D+X13 SGD-

ELCB-PB30NNDR

Y3Y2Y1Y0C0

X5X4X3X2X1X0

24G+24V

ELCB-PB30NNDR (18DI-DC/12DO-R)

S/S

X7X6

Y5Y4

X11X10 X12

Y6 Y7

X14X13 X16X15

C2 Y10 Y12Y11 Y13

X17

D-D+ SG

X20 X21

Y2Y1Y0ZP0UP0

X5X4X3

X2X1

24G+24V

ELCB-PB30NNDT (18DI-DC/12DO-T)

S/S

X7X6

Y5Y4

X11

X10 X12

Y6 Y7

X14

X13 X16X15

UP1 ZP1 Y11Y10 Y12

X17

D-D+ SG

Y13

X20 X21

ELCB-PB40NNDR/T

Y2Y1

X5X4X3X2X1X0

24G+24V

ELCB-PB40NNDR (24DI-DC/16DO-R)

S/S

X7X6

X11X10 X12

Y6 Y7

X14X13 X16X15

C2 Y10 Y12Y11 Y13

X17

D-D+ SGC3 Y14 Y15 Y17

Y16

X21X20 X22 X24X23 X26X25 X27

Y2Y1Y0ZP0UP0

X5X4X3X2X1X0

24G+24V

ELCB-PB40NNDT (24DI-DC/16DO-T)

S/S

X7X6

X11X10 X12

Y6 Y7

X14X13 X16X15

UP1 ZP1 Y11Y10 Y12

X17

D-D+ SGY13 Y14 Y15 Y17Y16

X21X20 X22 X24

X23 X26X25 X27

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Eaton Controller Handbücher

Eaton

Eaton Cutler-Hammer ELC Series Installationsanleitung

Eaton

Eaton CGLine+ Bedienungs- und Wartungsanleitung

Eaton

Eaton xComfort CHVZ-01/04 Bedienungsanleitung

Eaton

Eaton S801+ Series Bedienungsanleitung

Eaton

Eaton ELCM Series Bedienungsanleitung

Eaton

Eaton S811 Bedienungsanleitung

Eaton

Eaton ELC-PA10AADR Bedienungsanleitung

Eaton

Eaton COOPER POWER SERIES Service-Handbuch

Eaton

Eaton xComfort CSAU-01/03 Bedienungsanleitung

Eaton

Eaton AK-2-25-LV-VSR-425A Bedienungsanleitung

Eaton

Eaton PKZM01 Series Handbuch

Eaton

Eaton EMS 2,4 Series Bedienungsanleitung

Eaton

Eaton easyControl EC4-200 Bedienungsanleitung

Eaton

Eaton DS7 Series Handbuch

Eaton

Eaton SC100 Bedienungsanleitung

Eaton

Eaton ELC-PC12NNAR Bedienungsanleitung

Eaton

Eaton AMPGARD RVSS Bedienungs- und Wartungshandbuch

Eaton

Eaton ATC-900 Bedienungsanleitung

Eaton

Eaton CDAE-01/04 Bedienungsanleitung

Eaton

Eaton XV-102 Series Bedienungsanleitung

Eaton

Eaton HFX Series Bedienungsanleitung

Eaton

Eaton Crouse-hinds series Bedienungsanleitung

Eaton

Eaton ADS8 Series Handbuch

Eaton

Eaton CGLine+ Touchscreen Controller Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch