Eaton Cutler-Hammer Jockey Bedienungsanleitung

IM05805004K

Effective January 2003

Instructions for Cutler-Hammer

Jockey Pump Controllers

IM05805004K

Effective January 2003

TABLE OF CONTENTS

1. INSTALLATION AND MOUNTING OF THE CONTROLLER ............................................... 1

2. SYSTEM PRESSURE CONNECTIONS ............................................................................... 1

3. ELECTRICAL CONNECTIONS......................................................................................... 1

3.1 ELECTRICAL CHECKOUT INSTRUCTIONS ........................................................................................... 2

3.1.1 Motor Rotation Check............................................................................................................. 2

3.1.2 Pressure Switch Set Point ....................................................................................................... 2

3.1.3 Starting and Stopping ............................................................................................................. 2

3.1.4 Overload Relay Trip Setting ................................................................................................... 2

3.1.5 Running Period Timer (Optional)........................................................................................... 2

3.2 PRESSURE SWITCH SETTING INSTRUCTIONS...................................................................................... 3

4. FIGURE 1: TYPICAL SCHEMATIC .................................................................................. 4

5. FIGURE 2: DIMENSIONAL DRAWING ............................................................................ 5

6. FIGURE 3: OVERLOAD RELAY SELECTION CHART....................................................... 6

e i

IM05805004K Page 1

Effective January 2003

INSTALLATION & MAINTENANCE

MANUAL FOR THE JOCKEY

PUMP CONTROLLER

In order to familiarize yourself with the Jockey Pump Controller, please read the instruction manual thoroughly and

carefully. Retain the manual for future reference.

1. Installation and Mounting of the

Controller

Carefully unpack the controller and inspect

thoroughly.

It is recommended that the controller is located as

close as is practical to the motor it controls

The controller is not free standing and must be bolted

securely to a wall. For dimensional and weight data

please refer to the respective data sheets for the

Jockey Pump Controller.

2. System Pressure Connection

The Jockey Pump Controller is equipped with a

Pressure Switch. The controller is provided with a

¼” NPT female system pressure connection located

on the bottom, external side of the enclosure. The

connection should be installed as per NFPA,

pamphlet No. 20.

NOTE: Water lines to the pressure switch must be

free from dirt and contamination.

The pressure should not exceed what the pressure

switch is rated for.

3. Electrical Connections

All electrical connections should meet national

and local electrical codes and standards.

The controller should be located or so protected that

they will not be damaged by water escaping from

pumps or pump connections. Current carrying parts

of controllers shall be a minimum of 12 inches (305

mm) above the floor level.

•Prior to starting verify all data on the nameplate

such as, catalog number, AC line voltage and

horsepower.

•Inspect all electrical connections, components

and wiring for any visible damage and correct as

necessary. Ensure that all electrical connections

are tightened before energization.

•Install necessary conduit using proper methods

and tools.

•Incoming AC line voltage is clearly marked L1,

L2, L3 and ground, located at the top of the

breaker.

IM05805004K

Effective January 2003

3.1 Electrical Checkout Instructions

WARNING: The following procedures should be carried out by a qualified electrician familiar with the electrical

safety procedures associated with this product and its associated equipment..

3.1.1 Motor Rotation Check: With the controller energized, move the H.O.A. selector switch to "HAND" then back to

“OFF” immediately to check the direction of the motor and pump rotation. If rotation direction is not correct,

open the breaker and reverse the phase sequence of the load terminals of the contactor T1, T2, T3 or at the motor

terminals.

3.1.2 Set up pressure switch set point as described on page 3 in these instructions. These instructions check out

automatic starting and stopping.

3.1.3 Starting and Stopping: Energize the controller. With the H.O.A. selector switch set to “AUTO”, if the system

water pressure is lower than the pressure switch set-point pressure, the pump will start. The pump will stop when

pressure is restored. If the optional running period timer is included, the pump will run for the set time and then

reset provided pressure has been restored. For manual operation, set the H.O.A. selector switch to “HAND’ to

start the pump and “OFF” to stop.

3.1.4 Overload Relay Trip Setting: The trip setting must be set as indicated on the drawing inside the starter door or

according to the chart at the back of this manual.

3.1.5 Running Period Timer: (Optional) The RPT timer must be set for a minimum of 10 minutes. A calibrated dial is

provided on the front of the timer.

Page 3

Page 2

IM05805004K

Effective January 2003

3.2 Pressure Switch Setting Instructions

Before attempting to set the pressure switch, de-energize the jockey pump controller by opening the Circuit Breaker. This

is done for safety, and so that the jockey pump will not start and interfere with the adjustment procedure.

1. Set the differential adjustment on the pressure switch to minimum by turning the Differential Adjusting Screw fully

counter clockwise. Set the operating pressure to well below the required pump starting pressure. Turn the Range

Adjusting Screw clockwise to reduce the pressure and observe the scale on the switch.

2. Bleed the fire protection water system until the pressure is reduced to the required pump starting pressure. Hold this

pressure by closing the drain valve.

3. Slowly rotate the Range Adjusting Screw counter clockwise until a click is heard from the pressure switch. The

switch is now set to the required pump starting pressure.

4. If it is necessary to re-adjust the differential, the operating pressure of the switch will also be changed and should be

reset.

NOTE: The cut-in (start point) pressure is the cut-out (range adjusting setting) pressure minus the differential setting.

IM05805004K

Effective January 2003

Page 4

IGURE # 1

IM05805004K

Effective January 2003

FIGURE # 2

Page 5

IM05805004K

Effective January 2003

FIGURE #3

Page 6

Inhaltsverzeichnis

Andere Eaton Controller Handbücher

Eaton

Eaton CGLine+ CGVision Series Bedienungs- und Wartungsanleitung

Eaton

Eaton Ampgard 720A Programmierhandbuch

Eaton

Eaton HFX Series Bedienungsanleitung

Eaton

Eaton xComfort CSAP-01/XX Bedienungsanleitung

Eaton

Eaton FP-25-LV-VSR Bedienungsanleitung

Eaton

Eaton JOCKEY Touch Technisches Datenblatt

Eaton

Eaton WaveLinx series Bedienungsanleitung

Eaton

Eaton COOPER POWER SERIES Bedienungsanleitung

Eaton

Eaton DCF 800 TWIN Bedienungsanleitung

Eaton

Eaton xComfort CRCA-00/10 Gebrauchsanweisung

Eaton

Eaton EMS-SWD Series Bedienungsanleitung

Eaton

Eaton SV9000 Bedienungsanleitung

Eaton

Eaton S811+N37 series Bedienungsanleitung

Eaton

Eaton PKE-SWD-32 Handbuch

Eaton

Eaton FC6 Bedienungsanleitung

Eaton

Eaton DILM12-XPBC Handbuch

Eaton

Eaton Jockey lite Bedienungsanleitung

Eaton

Eaton OPTE9 Bedienungsanleitung

Eaton

Eaton DS7 Series Handbuch

Eaton

Eaton S701 Handbuch

Eaton

Eaton PowerXL DE1 series Bedienungsanleitung

Eaton

Eaton CGLine+ Web Controller Bedienungsanleitung

Eaton

Eaton AK-2-25-LV-VSR-425A Bedienungsanleitung

Eaton

Eaton RTC-100 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch