Eaton S611 Handbuch

Installation Leaet IL03901007E Effective June 2011

S611 User Interface Remote Mounting

Installation Leaﬂet

Disconnect power in accordance with federal, state, and local codes and remove the S611 from the enclo-

sure or mounting panel.

NOTE: Servicing the S611 while installed in an enclosure or mounted vertically on a panel is not recom-

mended.

Place the unit on a clean work surface.

Cover Removal

1. Disconnect all control wiring and tie wraps securing any wiring to the cover assembly.

2. Remove cover screws with nuts. 6 each on Frames A – D, 4 each on Frames E - F.

NOTE: Cover screw nuts are prevented from rotating but are not retained in place by the pole

supports. Do not allow hardware to fall into the soft starter.

3. Lift top of cover approximately 6” to gain access to the BYPASS VOLTAGE contactor

connector mounted on the Printed Circuit Board (PCB). See Figure 1.

4. Press locking tab on BYPASS VOLTAGE contactor connector and disconnect from the PCB.

5. Carefully rotate cover to rest onto work surface as shown. See Figure 2.

Figure 1 - Contactor Connector Figure 2 - Cover Position

Mounting The Remote Display

If necessary, remove the User Interface from the cover using a 30mm pilot device tool (E22CW recom-

mended).

1. Drill or punch two 30mm pilot holes on 1.75-inch centers a minimum of 1.60 inches (40.6 mm)

from every door gasket (see Figure 3).

2. Insert remote display through the door and add two gaskets provided behind the door

(see Figure 4).

Installation Leaet IL03901007E

Effective June 2011

S611 Soft Starters

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Publication No. IL03901007E

June 2011 Rev.001

PowerChain Management is a registered

trademark of Eaton Corporation.

All other trademarks are property of their

respective owners.

Figure 3 - Pilot Device Holes - Inch[mm]

Minimum to all

gaskets ordoor

mounteddevices

1.60

[40.6]

1.75

[44.5]

Gaskets

E22CW

Tighten

Figure 4 - Door Cut Away For Clarity

3. Orient strain relief bracket with respect to your chosen cable routing.

4. Add two jam nuts provided and tighten 30mm pilot device tool until the strain relief bracket is

flush with the enclosure door, tighten an additional ½ of a turn.

Connecting the Remote Display

1. Route cable from User Interface to PCB (see Figures 5 & 6).

2. Secure cable to the strain relief bracket using any suitable tie wrap.

3. Reinstall cover assembly.

Figure 5 - Interconnecting Cable - PCB Figure 6 - Interconnecting Cable - User Interface

Cover Reinstallation

1. As the cover is placed onto the supports, carefully guide wiring into place.

2. Ensure that the BYPASS VOLTAGE contactor connector is properly connected prior to installing

the cover screws.

3. Install and torque all cover assembly screws to 22 – 27 lb-in.

4. Reinstall control wiring.

Andere Handbücher für S611

Inhaltsverzeichnis

Andere Eaton Controller Handbücher

Eaton

Eaton A200 Handbuch

Eaton

Eaton S611 Bedienungsanleitung

Eaton

Eaton CGLine+ Touchscreen Controller Bedienungsanleitung

Eaton

Eaton S611 Bedienungsanleitung

Eaton

Eaton Ampgard 400 Bedienungsanleitung

Eaton

Eaton LS Series Handbuch

Eaton

Eaton Cutler-Hammer S801TR Bedienungsanleitung

Eaton

Eaton Vikers V200 Series Bedienungsanleitung

Eaton

Eaton xComfort CDAE-01/01 Bedienungsanleitung

Eaton

Eaton Cutler-Hammer ELC Series Installationsanleitung

Eaton

Eaton Cutler-Hammer ATC-300 Bedienungsanleitung

Eaton

Eaton SV9000 Bedienungsanleitung

Eaton

Eaton ELC-PC12NNAR Bedienungsanleitung

Eaton

Eaton Cutler-Hammer Easy-Start ES Series Bedienungsanleitung

Eaton

Eaton Digitrip RMS Handbuch

Eaton

Eaton C22- P Series Handbuch

Eaton

Eaton S811 Bedienungsanleitung

Eaton

Eaton LMR PLUS Bedienungsanleitung

Eaton

Eaton xComfort CSAU-01/01 Handbuch

Eaton

Eaton DILM12-XPBC Handbuch

Eaton

Eaton xComfort CAAE Series Handbuch

Eaton

Eaton CDAE-01/05-I Bedienungsanleitung

Eaton

Eaton Cutler-Hammer W200 Bedienungsanleitung

Eaton

Eaton DE1-121D4 Series Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung