Eaton AGSVX9000 Bedienungsanleitung

AGSVX9000 Drives

Quick Setup Guide

Effective May 2013

New Information

CONTENT

STEP 1 — Keypad Operation Overview

STEP 2 — Standard Wiring Diagrams and Connections

STEP 3 — Start-Up Wizard

STEP 4 — Operating and Programming Menu

Navigation

STEP 5 — Faults and Warning Indication

STEP 6 — Monitoring Menu

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 1

Keypad Operation Overview

Keypad and Display

LCD Status Indicators

LED Status Indicators

Indicator Description

Run

Indicates that the AGSVX9000 is running and controlling the load.

Blinks when a stop command has been given but the AGSVX9000

is still ramping down.

Counterclockwise Operation

The output phase rotation is BAC, corresponding to counterclockwise

rotation of most motors.

Clockwise Operation

The output phase rotation is ABC, corresponding to clockwise rotation

of most motors.

Stop

Indicates that the AGSVX9000 is stopped and not controlling the load.

Ready

Indicates that the AGSVX9000 is ready to be started.

Alarm

Indicates that there is one or more active drive alarm(s).

Fault

Indicates that there is one or more active drive fault(s).

I/O Terminal

Indicates that the I/O terminals have been chosen for control.

Keypad

Indicates that the keypad has been chosen for control.

Bus/Communications

Indicates that the communications bus control has been chosen for

control.

Indicator Description

local Local — Steady Illumination

Indicates that the AGSVX9000 is ready to be started and operated

from the Local mode.

Local — Flashing

Indicates that the AGSVX9000 is ready for operating command

to select Local or Remote operation.

remote Remote

Indicates that the AGSVX9000 is operating and controlling the load

remotely.

Remote — Flashing

Indicates that the AGSVX9000 is ready for operating command

to select Local or Remote operation.

fault Fault

Indicates that there is one or more active drive fault(s).

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 1 (Continued)

Navigation Buttons

Menu Navigation

Navigation Tips

To navigate within one level of a menu, use the up and down arrows.

To move deeper into the menu structure and back out, use the right

and left arrows.

To edit a parameter, navigate to show that parameter’s value, and press

the right arrow button to enter the edit mode. In edit mode, the

parameter value will ﬂash.

Button Description

Start

This button operates as the START button for normal operation when

the “Keypad” is selected as the active control.

Enter

This button is used in the parameter edit mode to save the parameter

setting and move to the next parameter …

•

to reset the Fault History if pressed while in the “Fault History”

menu.

•

to conﬁrm the acceptance of a change.

•

to change a virtual button status while in the “Button” menu.

•

to conﬁrm the start-up list at the end of the Start-Up Wizard.

•

when the “Operate” menu is active, to exit the “Operate” submenu.

Stop

This button has two integrated operations. The button operates as

STOP button during normal operation …

•

motor STOP from the keypad, which is always active unless

disabled by the “StopButtonActive” parameter.

•

used to reset the active faults.

Reset

Resets the active faults.

Local / Remote

Switches between LOCAL and REMOTE control for start, speed

reference and reverse functions. The control locations corresponding

to local and remote can be selected within an application.

Left Arrow

•

navigation button, movement to left.

•

in parameter edit mode, exits mode, backs up one step.

•

cancels edited parameter (exit from a parameter edit mode).

•

When in “Operate” menu will move backward through menu.

•

At end of “Start-Up Wizard”, repeats the “Start-Up Wizard”

setup menu.

Right Arrow

•

navigation button, movement to right.

•

enter parameter group mode.

•

enter parameter mode from group mode.

•

When in “Operate” menu will move forward through menu.

Up and Down Arrows

•

move either up or down a menu list to select the desired menu item.

•

editing a parameter/password, while the active digit/character is

scrolled.

•

increase/decrease the reference value of the selected parameter.

•

in the “Operate” menu, will cause the display of the active reference

source and value and allow its change if the keypad is the active

reference source. Used to set the password (if deﬁned) when

leaving the “Operate” menu.

•

scroll through the “Active Faults” menu when the AGSVX9000

is stopped.

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 1 (Continued)

When in edit mode, the parameter value can be changed by pressing

the up or down arrow keys.

When in edit mode, pressing the right arrow a second time will allow

you to edit the parameter value digit by digit.

To conﬁrm the parameter change you must press the ENTER button.

The value will not change unless the ENTER button is pushed.

Some parameters can not be changed while the AGSVX9000 is running.

The screen will display LOCKED if you attempt to edit these parameters

while the drive is running. Stop the drive to edit these parameters.

See the AGSVX9000 Application Manual for identiﬁcation of these

parameters speciﬁc to your chosen application.

Main Menu

The data on the control keypad are arranged in menus and submenus. The

ﬁrst menu level consists of M1 to M8 and is called the Main Menu. The Main

Menu is illustrated on Page 7. Some of the submenus will vary for each

application choice.

STEP 2

Standard Wiring Diagrams and Terminal Locations

Power and Motor Wiring Terminal Schematic for AGSVX9000 Drives

AGSVX9000 Power and Motor Wiring for Low Horsepower Drives (1 – 30 hp)

UVW

B+

L1 L2 L3

L1 L2 L3 B- R- T1T2T3

External

RFI-Filter

(Optional)

External

Filter

(Optional)

Power

Board

230V 1 – 15 hp

480V 1-1/2 – 30 hp

Control

Board

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 2 (Continued)

AGSVX9000 Power and Motor Wiring for

Large Horsepower Drives (20 – 250 hp)

B+

L1 L2 L3

L1 L2 L3 B- R-

External

RFI-Filter

(Optional)

External

Filter

(Optional)

Power

Board

230V 20 – 30 hp

480V 40 – 250 hp

Control

Board

UVW

T1T2T3

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 2 (Continued)

Standard Application Default I/O Configuration

Note: For more information on jumper selections, see the

9000X AF Drives User Manual, Chapter 4.

110

11 2

A2-

Lout-

D01

RELAY OUTPUT 1

RELAY OUTPUT 2

FAULT

RUN

DIGITAL OUTPUT READY

ANALOG OUTPUT

OPTA2

ACCEL./DECEL.TIME SELECT

CONTROL VOLTAGE OUTPUT

MULTI-PURPOSE APPLICATION

CONTROL VOLTAGE OUTPUT

GND

DIN6

CMB

Lout+

DIN5

DIN4

CMA

24Vout

DIN1

DIN2

DIN3

I/O GROUND

DIN4-DIN6 COMMON

EXTERNAL FAULT

RUN ENABLE

OUTPUT FREQUENCY

DIN1-DIN3 COMMON

START PULSE

STOP PULSE

FAULT RESET

Vin+

24Vout

Lin-

GND

Lin+

GND

A9-

+10V

ANALOG INPUT VOLTAGE

I/O GROUND

ANALOG INPUT CURRENT

(RANGE 4-20mA)

(RANGE 0-10 VDC)

I/O GROUND

REFERENCE OUTPUT

OPTA9

X6 A

TOWER

FAULT

METER

CONTACT

TBA-14

TBA-12

(3) (4)

(2)

(1)

START

STOP

PB2

PB1

TBA-14A

14A

CMB connected to GND

CMA connected to GND

CMB isolated from GND

CMA isolated from GND

CMB and CMA internally connected

together, isolated from GND

= Factory default.

Jumper Block X3:

CMA and CMB Grounding

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

Notes

1Total motor nameplate amps x nameplate service factor.

2Set according to motor nameplate.

Continue to make changes to the following parameters.

Parameter Number Parameter Name Desired Setting

P1.2.1.1 Start Mode Start P–Stop P

P1.2.7.2 Start 2 DigIn:A.2

P1.2.7.3 Run Enable DigIn:A.3

P1.2.7.10 Fault Reset DigIn:0.1

P1.3.3.2 Run DigOut:B.1

P5.7.2 Fan Control Calc Temp

STEP 3

Start-Up Wizard

If the wizard is not enabled at power-up, press the STOP button for 5 secs.

to enable it.

Accel. Time 1

“30” s

Decel Time 1

“30” s

Current Limit

Nameplate Volt

“460” V “60.00” Hz

Power Factor Loc. Ctrl. Place

“Keypad”

Input Phase Supv

“0 – No Response”

Repeat Setup?

Rem. Ctrl. Place

“I/O Terminal”

Local Reference

“Keypad”

Remote Reference

“Keypad”

Startup Wizard

“Press Enter”

Language

“English”

Application

“Multipurpose”

3–5 Seconds Wait

Setup Starts

“Press Enter”

Min. Freq

“0.00” Hz

Max. Freq

“60.00” Hz

Setup Done

Press Enter

Copy Parameters

Up to Keypad

Up to Keypad

Wait

Output Frequency

“0.00” Hz

P1.1.1 P1.1.2

P1.1.3 P1.1.4 P1.1.5

P1.1.6 P1.1.7 P1.1.8

P1.1.9 P1.1.10 P1.1.11

P1.1.12 P1.1.13 P1.1.14

P1.7.4

Motor Nameplate Freq

Motor Nameplate Speed

Motor

Nameplate Current

Motor

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 4

Operating & Programming Menu Navigation

Main Menu

The data on the control keypad are arranged in menus and submenus. The

first menu level consists of M1 to M8 and is called the Main Menu. The

structure of these menus and their submenus is illustrated below. Some of

the submenus will vary for each application choice.

Main Menu Navigation

Note: Enter Key — Holding the “Enter” key for more than 3 seconds will

allow you to go directly to the programming mode.

M1 Parameters

M2 Keypad Control

M3 Active Faults

M6 Expander Boards

M7 Monitor

M8 Operate Mode

G1.1

. . .

R2.1 Keypad Reference

P2.2 Keypad Direction

P2.x Stop Button Active

A3.1 Active Fault 1

T3.1.1 Operation Days

. . .

T3.1.13 Zero Speed

A3.x Active Fault x

V7.1 Output Frequency–0.00 Hz

V7.2 Frequency Reference–0.00 Hz

. . .

G1.x

G6.1 Slot A Board

. . .

G6.5 Slot E Board

O1 Output Frequency–0.0 Hz

O2 Freq Reference–0.0 Hz

. . .

Ox . . .

M7.1x Multimonitor

Menu Navigation:

Up Arrow — The up arrow

advances to the next

menu item.

For example, pressing the

up arrow once will

advance from M1 to M2.

Down Arrow — The down

Right Arrow — The right

Left Arrow — The left

arrow backs up to the

previous menu item.

arrow will advance to the

next level in the menu.

arrow will back up one

level in the menu

structure.

For example, pressing the

down arrow once will back

up from M2 to M1.

For example, pressing the

right arrow once will

advance from M2 to R2.1.

For example, pressing the

left arrow once will back

up from R2.1 to M2.

M5 System Menu

S5.1 Language

S5.2 Application

S5.3 Copy Parameters

S5.4 Compare Parameters

S5.5 Security

S5.6 Keypad Settings

S5.7 Hardware Settings

S5.8 System Information

. . .

M4 Fault History

H4.1 Most Recent Fault

T4.1.1 Operation Days

. . .

T4.1.13 Zero Speed

N7.1x.1

H4.1.x Oldest Saved Fault

. . .

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 4 (Continued)

Operate Menu — M8

The Operate Menu provides a easy to use method of viewing key numerical

Monitoring Menu items. Some applications also support the setting of

reference values in this menu. The items displayed vary by application. The

table below is an example for the Standard application.

Operate Menu Items — Standard Application Example

The menu is navigated by using the left and right arrow buttons. If a

reference level is available for setting, the up and down arrow buttons adjust

the value. To exit the Operate Menu to access the other menus, depress the

ENTER button for 2 seconds. While in the other menus, if there is no keypad

activity, the display will return to the Operate Menu after 30 seconds.

Code Signal Name Unit Description

O.1 Output Frequency Hz Output frequency

O.2 FreqReference Hz Frequency reference

O.3 Motor Speed rpm Calculated motor speed

O.4 Motor Current A Measured motor current

O.5 Motor Torque % Calculated torque based on nominal motor

torque

O.6 Motor Power % Calculated power based on nominal motor

power

O.7 Motor Voltage V Calculated motor voltage

O.8 DC-Bus Voltage V Measured DC-bus voltage

O.9 Unit Temperature °C Heatsink temperature

O.10 MotorTemperature % Calculated motor temperature based on the

motor nameplate information and the

calculated motor load

R1 Keypad Reference Hz Keypad frequency reference setting

AGSVX9000 Drives

MN040001EN—May 2013 www.eaton.com

STEP 4 (Continued)

Parameters—M1

Standard Parameters—M1

1. If Startup Wizard is not present on the keypad when performing the

startup, the Startup Wizard can be forced by:

a. With power on, hold the keypad stop button for 5 seconds.

b. When “Wizard activated—Yes” appears, release the button.

c. De-energize the VFD until the keypad display goes away.

d. Energize the VFD.

2. When using the Startup Wizard, be sure that the Multipurpose

Application is selected (second question in the wizard, after selecting

language).

3. Once the Wizard has been completed, the following parameters need

to be verified or adjusted as necessary to properly set up the software

for the application.

Parameter Number Parameter Name Desired Setting

P1.1.1 Min Frequency 0 Hz

P1.1.2 Max Frequency 60 Hz

P1.1.3 Accel Time 1 30 Seconds

P1.1.4 Decel Time 1 30 Seconds

P1.1.5 Current Limit Total Motor Nameplate

Amps x Service Factor

P1.1.6 thru P1.1.10 Motor Nameplate Values Set according to Motor

Nameplate

P1.1.11 Local Control Place Keypad

P1.1.12 Remote Control Place I/O Terminal

P1.1.13 Local Reference Keypad

P1.1.14 Remote Reference Keypad

P1.2.1.1 Start Mode Start P–Stop P

P1.2.7.2 Start 2 DigIn:A.2

P1.2.7.3 Run Enable DigIn:A.3

P1.2.7.10 Fault Reset DigIn:0.1

P1.3.3.2 Run DigOut:B.1

P5.7.2 Fan Control Calc Temp

Inhaltsverzeichnis

Andere Eaton Gleichstromantrieb Handbücher

Eaton

Eaton DC1-1D Series Handbuch

Eaton

Eaton PowerXL DH1 Gebrauchsanweisung

Eaton

Eaton PowerXL DM1 Series Bedienungsanleitung

Eaton

Eaton Crouse-hinds series Einrichtungshandbuch

Eaton

Eaton Cutler Hammer PowerXL DC1 E1 Series Bedienungsanleitung

Eaton

Eaton PowerXL DM1 Series Handbuch

Eaton

Eaton M-Max series Bedienungsanleitung

Eaton

Eaton PowerXL DH1 Handbuch

Eaton

Eaton PowerXL DG1-323D7FB-C21C Bedienungsanleitung

Eaton

Eaton DA- -A20 Series Handbuch

Eaton

Eaton DC1-S2 Series Handbuch

Eaton

Eaton PowerXL DM1 Series Handbuch

Eaton

Eaton PowerXL DC1 Bedienungsanleitung

Eaton

Eaton PowerXL DG1 Bedienungsanleitung

Eaton

Eaton PowerXL DG1 Series VFD Bedienungsanleitung

Eaton

Eaton PowerXL DA1 Gebrauchs- und Pflegehandbuch

Eaton

Eaton BACnet MS/TP OPTCJ Bedienungsanleitung

Eaton

Eaton PowerXL DC1 Bedienungsanleitung

Eaton

Eaton PowerXL DB1 Bedienungsanleitung

Eaton

Eaton M-Max series Bedienungsanleitung

Eaton

Eaton H-Max Series Bedienungsanleitung

Eaton

Eaton M-Max series Bedienungsanleitung

Eaton

Eaton PowerXL DM1 Series Bedienungsanleitung

Eaton

Eaton SV9000 Gebrauchsanweisung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung