Eaton I-on Compact Bedienungsanleitung

i-on Compact Security System

User Guide

Figure 1. i-on Compact

About this guide

This guide provides an

introduction to i-on Compact

alarm systems for users. It

describes the main components

of the alarm system, the key

features and how to carry out

typical day-to-day tasks.

If you need additional

information, including details of

the options in the User menu,

please refer to the i-on Compact

Administration and User Manual.

All manuals referred to are

available from our web site.

Contents

About this guide ............. 1

About i-on Compact .......... 2

System components .......... 2

Control unit.......................... 2

Detectors............................ 2

External sirens ....................... 2

Network cameras ..................... 3

Remote controls ..................... 3

HUA transmitters ..................... 3

Internal radio sounders ................ 3

Output devices ....................... 3

Key features ................. 3

Comprehensive set/unset flexibility ...... 3

Alarm communication ................. 3

Proximity tags........................ 4

Eaton SecureConnect™................ 4

System control using SMS texts ........ 4

Users and user types .................. 4

Wide range of peripherals.............. 4

Camera integration ................... 4

Control of external devices (outputs)..... 4

HUA/panic alarms .................... 4

Installer remote access ................ 4

Wide range of user options............. 5

Ability to omit zones .................. 5

Full logging.......................... 5

Jamming and tamper monitoring ....... 5

Comprehensive test options ............ 5

Using i-on Compact .......... 5

Control unit keypad ................... 5

About the standby screen .............. 6

Setting the system .................... 6

Unsetting the system.................. 6

Managing alarms ..................... 6

Accessing the User menu .............. 7

Omitting zones ....................... 7

Using SecureConnect ......... 8

Installing the app ..................... 8

Pairing the app ....................... 8

Using the app ........................ 8

Cybersecurity ........................ 9

i-on Compact

10:43 03/06/2017 LCD display

Keypad

Proximity

tag reader

Page 2

About i-on Compact

Thank you for choosing i-on Compact –

one of the most advanced and trusted

means available today to protect people

and property. The i-on Compact is a high-

reliability radio alarm system for up to

20 zones, intended for use in small to

medium-sized domestic applications.

Your i-on Compact is future-flexible: as

Eaton develop new features, your alarm

system can be updated remotely or locally

with the latest software.

i-on Compact alarm systems provide a

comprehensive range of communication

options, configuration settings and

peripheral devices, which provide the

flexibility needed to customise the system

to match the requirements of the most

demanding applications.

System components

This section outlines typical components

that your alarm system may include. Other

components may be used, depending on

your requirements.

Control unit

This is the main processing unit of the

alarm system. From a user’s view, its main

features are as follows (Figure 1):

•LCD display –This shows messages,

prompts and options that guide you

through the user interface.

•Keypad – This allows you to set or

unset the system, access user options

and acknowledge alarms. You can

identify yourself to the system by

entering your unique access code at

the keypad.

•Proximity tag reader – Each user

can have a unique proximity tag.

Presenting your tag accesses the

system in the same way as if you had

entered your access code.

Detectors

Detectors are devices that detect alarm

conditions. Below are some popular

examples, all of which can connect

wirelessly (via radio) to the control unit.

Note: Many other detectors are available,

including flood, shock and glass-break

sensors – please contact your installer for

details.

Passive Infra-Red (PIR)

movement detector.

Pet-tolerant versions are

available.

Smoke detector.

Door contact – to detect

when doors are opened.

Perimeter PIR detector – to

monitor external areas

such as gardens. Dual-

sensor technology and

pet-tolerant mode ensure

reliable outside operation.

Note: A zone is the lowest-level item

that you can set or unset. Since there is

normally only one detector per zone, the

terms “zone” and “detector” are often

used interchangeably.

External sirens

These are mounted

externally, high up in

a visible location for

deterrence. They include

a powerful sounder and

strobes. Up to 2 external

radio sounders can be

used.

Page 3

Network cameras

Internal and external

network cameras are

available.

These allow the

control unit to record

and optionally email

images when an alarm

occurs.

Remote controls

Each user can have a

portable remote control

to set or unset the system

or operate output devices

from a distance.

HUA transmitters

Small portable

Hold-Up Alarm (HUA)

transmitters, also

known as Panic Alarms

(PAs), allow you to

start alarms remotely.

Internal radio sounders

These are intended for use

in areas that are out of

audio range of the control

unit but where users need

to hear alarms, entry

tones, exit tones and other

sounds.

Output devices

The installer can configure the system to

control externals devices, which you can

switch on or off from the control unit or

a remote control, or which can operate

automatically when, for example, an alarm

occurs.

The system supports up to 20 radio

outputs.

Key features

This section provides an overview of the

key features, from a user’s perspective, of

i-on Compact alarm systems.

Note: Some features described in this

guide may not be available, depending on

configuration. Please ask your installer if

you would like them to be available.

Comprehensive set/unset flexibility

There are many options available to

the installer to configure the setting/

unsetting process to match your specific

requirements.

If at any time, your requirements change,

please contact your installer, who may

be able to adjust the set/unset procedure

without making any physical changes.

The control unit can set in one of four

ways: either full set or one of three part

sets (part set B, C or D).

When the system is full set, all zones are

set. When the system is part set, only

the zones that belong to the part set are

set. A part set may, for example, set the

downstairs areas, leaving the upstairs

unset (e.g. for use during the night).

Alarm communication

When the system detects an alarm, it starts

the external sounder/strobe units and

operates internal sounders, including the

sounder in the control unit.

If you wish, your installer can also

configure the control unit to communicate

alarms externally to:

•An Alarm Receiving Centre (ARC), via

the internet or a fixed-line telephone

network.

•An email address.

•A mobile phone using a text message.

Note: Communications via the internet

is provided as standard. Connecting the

control unit to a mobile (GSM) or fixed-

line (PSTN) phone network requires the

installer to fit a plug-on module.

Page 4

Proximity tags

Each user can have a unique

proximity tag. When presented to

the control unit, the tag performs

the same action as entering your

access code.

Proximity tags make it easier for you to set

or unset the system, and there is no need

to remember an access code.

Eaton SecureConnect™

The Eaton SecureConnect app

allows you to monitor and

control your alarm system

over the internet from your

phone or tablet.

Please refer to page 8 for

details of how to install and

use the app.

System control using SMS texts

i-on Compact

10:43 03/06/2017

You can use SMS

text messages sent

from a mobile

phone or other

messaging device

to set/unset the

system, activate/deactivate outputs, omit/

un-omit zones or query the current status

of the system.

For further information, please refer to the

SMS Command Messaging User’s Guide.

Users and user types

i-on Compact gives you the ability to

define many different users, each of which

has a unique access code, proximity tag,

remote control and HUA transmitter.

You can also use “master” and “normal”

user types to specify the access each user

has to the system.

Wide range of peripherals

i-on Compact supports a wide range of

peripheral devices (see from page 2),

which gives the system flexibility to match

current requirements and adapt to meet

future requirements.

Camera integration

The control unit can record

images from network

cameras when an alarm

occurs, and associate those

images with the event.

If required, the system can send the

images to an email address when an alarm

occurs.

Control of external devices (outputs)

Your installer can set up your alarm system

to switch external devices, such as lights or

heating systems, on or off.

Devices can switch on or off automatically,

such as when the system is set.

Alternatively, you can switch them on or

off manually from the control unit or using

a remote control.

HUA/panic alarms

You can generate Hold-Up

Alarm (HUA), otherwise known

as a panic alarm, from the control unit, a

remote control, hand-held HUA transmitter

or using a separate panic button.

Installer remote access

The installer has a separate Installer

menu, which contains the options needed

to configure your system. The menu can

be accessed through the keypad on the

control unit.

An alternative is to allow the installer

to access your system remotely over

the internet, which may provide service

benefits.

Page 5

You have the ability to enable or disable

remote access as required through the

User menu.

Wide range of user options

Authorised users can access a User menu

from the control unit. The menu contains

options to add users, omit zones, view log

information, test the system, configure the

system and switch devices (outputs) on or

off.

You can find full details of the user options

in the i-on Compact Administration and

User Manual.

Ability to omit zones

You can omit a zone before setting the

system (see page 7). Omitting a zone

temporarily excludes it from setting.

You may want to omit a zone to prevent

false alarms if, for example, the area

it protects is going to be temporarily

occupied while the rest of the system is

set.

Full logging

The control unit logs all actions, alarms

and alerts. You can review the logged

events through the User menu.

Jamming and tamper monitoring

i-on Compact uses advanced techniques

to monitor your system continuously for

possible jamming or tamper attacks.

Comprehensive test options

The User menu contains a comprehensive

set of options that you can use to test the

system or to determine the owner of a

device such as a proximity tag or remote

control.

Using i-on Compact

This section describes typical tasks that

you may need to carry out from time to

time once the system is set up.

Note: For further information about these

and other tasks, please refer to the i-on

Compact Administration and User Manual.

Control unit keypad

Figure 2. Control unit keypad

The keys have the following functions:

Navigation key:

Scrolls up, or moves the

cursor left.

Scrolls down, or moves the

cursor right.

Changes the value, displays

further information, or inserts

a space.

Changes the value, or

deletes the character to the

left.

The key glows red or green to

indicate system status (green

= normal; red = alarm/fault).

This key exits an option or

cancels a change.

Confirms an action, such

as selection of an option or

acknowledgement of an alarm.

Pressing this key gives you

access to the user menu

when the standby screen is

displayed (see page 7).

Page 6

Carries out a full system set*.

Sets part set B, C or D*.

A Hold Up Alarm (HUA) is

started when both of these

keys are pressed (if enabled

by the installer).

*This is the default action; the installer can

configure these keys to operate outputs.

About the standby screen

When the system is idle (either while set

or unset), the display shows the “standby

screen”. For example:

i-on Compact

10:43 03/06/2017

Setting the system

Readying the system to start an alarm if

someone moves into a protected area is

called “setting” the system.

You can set your system using a variety of

different methods, depending on system

configuration. The following explains a

typical method using the control unit.

Note: Please refer to the Administration

and User Manual for full details.

1. Enter your access code or present your

proximity tag at the control unit. If you

enter your access code, the display

shows a * for each completed digit:

Enter Access Code:

(* )

2. If setting options are displayed, you

can press or followed by to

choose the option you require:

Setting Options

Full Set

•

Full Set

: To set the whole system.

Alternatively, press the A key*.

•

Part Set B\C\D

: To set part set B, C or

D only. Alternatively, press the B, C

or D key*.

*Your installer may have configured

the system to allow you to quick set

using A, B, C or D without entering an

access code or presenting a proximity

tag first.

3. You will hear a continuous exit tone

(unless the system is configured for

silent or instant setting).

The system sets when one of the

following occurs, depending on how

the system is configured:

•Immediately.

•After a period of time.

•When you exit the premises.

The A (full set), or B, C or D (part set)

key illuminates to indicate the set

status (unless disabled by the installer).

Unsetting the system

Disarming the system so that people

can move freely is called “unsetting” the

system.

To unset the system from the control unit:

1. Enter through the designated entry

route. Do not stray from this route –

you may cause an alarm.

2. If you hear a tone, go directly to the

control unit, since you will have limited

time to unset the system before it

generates an alarm.

3. Enter your access code or present your

proximity tag.

Managing alarms

If there is an alarm, you will need to

silence the sirens and sounders (if they are

still running), acknowledge the cause of the

alarm and reset the system.

Note: Please refer to the Administration

and User Manual for full details.

Page 7

To silence, acknowledge and reset an

alarm:

1. Make sure that it is safe to enter the

premises.

2. Enter your access code or present your

proximity tag in the normal way. This

silences the alarm (if the sirens and

sounders are still operating).

3. The navigation key glows red and the

display shows, for example:

Press tick to reset

Zone 000

The display alternates between

showing the zone number (e.g. “Zone

000”) and alarm type.

4. If you see “reset” in the message (see

above):

•Press − this acknowledges the

alarm and resets the system. The

system returns to standby and is

ready to set again.The navigation

key returns to its normal (green)

state.

If you see “Call Installer” or “Call ARC”

at the top of the screen:

•Press − this acknowledges the

alarm, but you will need to call the

installer or ARC to reset the system.

Although the system is not reset, you

will still be able to set and unset the

system normally. The navigation key

and applicable set/unset icons stay

red until the alarm is reset.

If you see “RESET FAULTS”, call your

installer.

Accessing the User menu

The User menu gives access to user

options such as to omit zones, view log

information and add new users. The range

of options available to you depends on

your user type (privileges).

To access the User menu:

1. Make sure the display shows the

standby screen.

2. Press .

3. Enter your user code:

Enter Access Code:

(* )

The first option is displayed:

Omit Zones >

Press or to scroll through the

options, followed by to select the

option you require. The options are

fully documented in the Administration

and User Manual.

4. To leave the menu and return to the

standby screen, press (if necessary

several times).

Omitting zones

Omitting a zone prevents it from

generating an alarm if the zone is triggered

while the system is set. You may, for

example, want to omit a zone that protects

a garage to enable access without causing

an alarm while the system is set.

Note: The zone returns to normal operation

when the system is unset.

Note: You can omit only those zones that

the installer has specified can be omitted.

To omit zones:

1. Access the User menu, as described in

the previous section.

2. Select the

Omit Zones

option. The first

zone you can omit is displayed. For

example:

OMIT ZONES

Zone 000 I

An “O” is displayed at the end of the

line if the zone is Omitted. An “I” is

displayed if the zone is Included.

3. Press or to display the zone you

wish to omit, then to mark it for

omission. Press again if you made

Page 8

a mistake and want the zone to be

included.

Repeat this step for any other zones

you wish to omit (or change to be

included).

4. Press to store changes.

Using SecureConnect

The SecureConnect app allows you to

monitor and control your alarm system

over the internet from your Android™ or

Apple® iOS™ phone or tablet.

Figure 3. SecureConnect app (Status

screen)

Using the app, you can:

•View the status of your system.

•Receive notifications of alarms or set/

unset actions (even when the app is

not open).

•View camera images generated by an

alarm or other event.

•Set and unset the system.

•Switch outputs on or off.

Installing the app

You can install the app from the Google

Play™ store or Apple App Store® in the

normal way.

When prompted, register as a new user of

SecureConnect or tap

Already registered

(for example, if you have used the app on

a different phone).

Pairing the app

The first time you open the app, you are

prompted to enter a pairing code.

To generate the pairing code, display the

User menu at the panel keypad (using

your own user code) and select the

Pair

App

option. The pairing code is valid for 15

minutes.

The pairing code uniquely pairs your

app with your panel and user code. This

ensures that any actions you carry out

using the app will affect only your panel,

and are logged against your user code.

You can unpair or re-pair the app using the

menu.

Using the app

The app has Status, View Log and Outputs

pages, which you can access using the

icons at the bottom of the screen.

Using the Status page

The Status page (Figure 1) is

displayed when you open the app.

The page shows the current status

of your system and allows you to

set or unset the system.

To full set the system: tap .

To full unset the system: tap .

To set a part-set: swipe it from left to right.

Viewing log messages

Tap this button to view the panel’s

log messages. Please contact

your installer for details about the

messages.

Page 9

Viewing camera images

The icon is displayed next to any

log message that has associated camera

images. Tap the icon to display a list of the

images. Tap any image to view it.

Please contact your installer for details of

adding cameras to your system.

To zoom in or out: slide your thumb and

pointer finger together or away.

To download the image to your device:

tap .

To print or share the image: tap .

Switching outputs on or off

Tap this button to list outputs

configured by the installer as

“User Defined”.

Tap to switch the output on

or off. (Note: Outputs defined as “pulsed”

switch off automatically after a set period.)

Accessing menu options

Tapping displays menu options. For

example, to sign out or un-pair the app.

Viewing notifications

Your device receives a notification when

there is a set, unset or alarm at your panel.

Open the notification in the normal way.

Note: notifications are normally reliable,

but are dependent on third parties such as

Apple and Google and therefore delivery

cannot be guaranteed.

Signing out

For security reasons, the app signs you out

automatically after a period of inactivity or

if you use a different app. You can sign out

manually from the menu.

For further assistance, please contact your

installation engineer.

Cybersecurity

Make sure you take proper precautions to

protect your network from cyber threats.

For guidance, please refer to:

https:www.us-cert.gov/ncas/tips/ST15-002

Page 10

NOTES:

Andere Handbücher für i-on Compact

Inhaltsverzeichnis

Andere Eaton Sicherheitssystem Handbücher

Eaton

Eaton EVT-300 Installations- und Betriebshandbuch

Eaton

Eaton menvier300 Bedienungsanleitung

Eaton

Eaton 403-AP Handbuch

Eaton

Eaton i-on Series Bedienungsanleitung

Eaton

Eaton i-on1000EX Bedienungsanleitung

Eaton

Eaton DFDAP-M Bedienungsanleitung

Eaton

Eaton i-on50EX Bedienungsanleitung

Eaton

Eaton 415-TF Handbuch

Eaton

Eaton PH1 Bedienungsanleitung

Eaton

Eaton SDR-WEXT Bedienungsanleitung

Eaton

Eaton XB11 Bedienungsanleitung

Eaton

Eaton i-on Series Bedienungsanleitung

Eaton

Eaton CU1 Series Bedienungsanleitung

Eaton

Eaton i-on160EX Bedienungsanleitung

Eaton

Eaton menvier40 Bedienungsanleitung

Eaton

Eaton Activeline GH5 Bedienungsanleitung

Eaton

Eaton i-on30R+ Bedienungsanleitung

Eaton

Eaton SM87BG Bedienungsanleitung

Eaton

Eaton i-on Style Bedienungsanleitung

Eaton

Eaton Symphoni LX Base Bedienungsanleitung

Eaton

Eaton i-on40H+ Bedienungsanleitung

Eaton

Eaton Crouse-hinds series Benutzerhandbuch

Eaton

Eaton 423-TF Handbuch

Eaton

Eaton Crouse-hinds series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

Eaton i-on Compact Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken