Eaton 9PX 5000i RT3U Netpack Bedienungsanleitung

ИБП Eaton 9PX 5000i RT3U Netpack (9PX5KiRTN) - Eaton 9PX ModularEasy - Пользовательский мануал по установке (Русский)

Постоянная ссылка на страницу: https://eaton-power.ru/catalog/eaton-9px/eaton-9px-5000i-rt3u-netpack/

9PXMEZ6Ki

9PXMEZ11Ki

Installation

and user manual

English - Français

Deutsch - Español

Русский

ENGLISH

ModularEasy

9PXMEZ6Ki

9PXMEZ11Ki

Installation

and user manual

Service and support:

Call your local service representative

614-09354-01_EN

Page 2 614-09354-01_EN

Special symbols

The following are examples of symbols used on the ModularEasy to alert you to important information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

Important instructions that must always be followed.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)

in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Information, advice, help.

SAVETHESE INSTRUCTIONS.This manual contains important instructions

that should be followed during installation and maintenance of the ModularEasy and UPS.

The ModularEasy models that are covered in this manual are intended for installation in an environment

within 0 to 40°C, free of conductive contaminant.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

Certication standards (in use with UPS)

• Safety: IEC/EN 62040-1 / Ed.1: 2008.

• EMC: IEC/EN 62040-2 / Ed.2: 2006.

• Performance: IEC/EN 62040-3 / Ed.2.0: 2011.

• IEC 61000-4-2 (ESD): level 3.

• IEC61000-4-3(Radiatedeld):level3.

• IEC 61000-4-4 (EFT): level 4.

• IEC 61000-4-5 (Fast transients): level 4.

• IEC61000-4-6(Electromagneticeld):level3.

• IEC61000-4-8(Conductedmagneticeld):level4.

SAFETY INSTRUCTIONS

Page 3

614-09354-01_EN

ENGLISH

Safety of persons

• The system has its own power source when connected to the UPS (UPS battery). Consequently,

the power outlets may be energized even if the system is disconnected from the AC power source.

Dangerous voltage levels are present within the system.

Itshouldbeopenedexclusivelybyqualiedservicepersonnel.

• Theproductmustbeproperlygrounded,alwaysconnecttheearthwirerst

Product safety

• The ModularEasy connection instructions and operation described in the manual must be followed

in the indicated order. Disconnection and overcurrent protection devices shall be provided by others

for AC in/out circuits.

• CAUTION-Toreducetheriskofre,theunitconnectsonlytoacircuitprovidedwithbranchcircuit

overcurrent protection (please refer to the UPS User Manual for current rating).

The upstream circuit breaker must be easily accessible.

The unit can be disconnected from AC power source by opening this circuit breaker, and if still

connected to UPS, by previously shutting down the UPS (refer to the UPS User Manual)

• Check that the indications on the rating plate correspond to your AC powered system and to the

actual electrical consumption of all the equipment to be connected to the system.

• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be

easily accessible

• Never install the system near liquids or in an excessively damp environment.

• Never let a foreign body penetrate inside the system.

• Never expose the system to direct sunlight or source of heat.

• If the system must be stored prior to installation, storage must be in a dry place.

• The admissible storage temperature range is -15ºC to +60ºC.

Special precautions

• The ModularEasy is designed to work with approved EATON UPS (contact your Eaton reseller for

more information).

• All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.

• There are NO USER SERVICEABLE PARTS inside the ModularEasy.

SAFETY INSTRUCTIONS

Page 4 614-09354-01_EN

1. Introduction....................................................................................... 5

1.1 Environmental protection...................................................................................................5

2. Presentation...................................................................................... 6

2.1 Standard installation ..........................................................................................................6

2.2 Description / Panels...........................................................................................................7

2.3 Firmware upgrade .............................................................................................................8

2.4 Parallel UPS screen ...........................................................................................................8

2.5 Parallel setting ...................................................................................................................8

3. Installation ........................................................................................ 9

3.1 Inspecting the equipment..................................................................................................9

3.2 Unpacking the ModularEasy..............................................................................................9

3.3 Checking the accessory kit................................................................................................9

3.4 Tower installation ............................................................................................................. 10

3.5 Rack installation with non-included optional Rail Kit: 9RK ............................................... 10

3.6 Example of rack 19" setup with optional EBM 9PX EBM 240V....................................... 11

3.7 Example of battery integration system with non-included optional

Trollet Frame: BINTSYS.................................................................................................... 11

3.8 Installation requirements.................................................................................................12

4. Power cables connection ............................................................... 14

4.1 9PXMEZ6Ki......................................................................................................................14

4.2 9PXMEZ11Ki - with common Normal and Bypass AC source .......................................16

4.3 9PXMEZ11Ki - with separate Normal and Bypass AC source........................................18

5. Operations....................................................................................... 20

5.1 UPS parallel system start-up ...........................................................................................20

5.2 UPS maintenance with ModularEasy ..............................................................................21

5.3 UPS replacement with ModularEasy...............................................................................22

6.Troubleshooting .............................................................................. 24

7. Specications .................................................................................. 24

Contents

Page 5

614-09354-01_EN

ENGLISH

1. Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

The ModularEasy range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features

of your ModularEasy.

BeforeinstallingyourModularEasywithyourUPS,pleasereadrstthesafetyinstructions.

Then follow the indications in this manual, which completes the UPS Installation and User Manual.

To discover the entire range of EATON products, we invite you to visit our web site at

www.eaton.com/powerquality or contact your EATON representative.

1.1 Environmental protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

• The cardboard we use comprises over 50% of recycled cardboard.

• Sacks and bags are made of polyethylene.

• Packingmaterialsarerecyclableandbeartheappropriateidenticationsymbol

Materials Abbreviations Number in

the symbols

Polyethylene terephthalat PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations.

EATON works with companies in charge of collecting and eliminating our products at the end of their

service life.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing center for electrical and

electronic waste.

Page 6 614-09354-01_EN

2. Presentation

The Eaton® ModularEasy is an essential part of your Parallel system. It allows the connection of 2 UPS

together, moreover, it possible to service or even replace the UPS without affecting the connected loads.

You can safely eliminate the effects of UPS maintenance and guard the integrity of your equipment.

Providingoutstandingreliability,theEatonModularEasyuniquebenetsinclude:

• easy and fast connection to UPS due to Input/Output and signal "all in one" patented connector

(ModularEasy 5/6kVA range)

• "make before break" feature to allow full servicing (electrical power continuity) when switching from

UPS position to Bypass (and vice versa)

• communication feature with UPS: detection of ModularEasy connection and switch position

(Normal or Bypass)

• load connection by both terminal blocks and IEC outlets (16A C19).

2.1 Standard installation

Rack installation Tower installation

Description Weight

(lb/kg)

Overall Dimensions (inch/mm)

D x W x H

Rack Dimensions (inch/mm)

d x W x H

9PXMEZ6Ki 22.8 / 10.3 27 x 17 x 5 / 690 x 440 x 130 21.3 x 17 x 5 / 540 x 440 x 130

9PXMEZ11Ki 32.6 / 15 27 x 17 x 5 / 690 x 440 x 130 21.3 x 17 x 5 / 540 x 440 / 130

Page 7

614-09354-01_EN

ENGLISH

2. Presentation

2.2 Description / Panels

The ModularEasy has a manual Bypass rotary switch with three positions:

1UPS: the load is supplied by the UPS.

2Test: the load is supplied directly by the AC power source,

the two UPS are still supplied but their outputs are disconnected from

the load.

3Bypass: the load is supplied directly by the AC power source,

the two UPS are disconnected from the AC power source.

Lights indicate the ModularEasy power status:

4"UPS supply" green light is active when at least one UPS output is

available.

5"Bypass mode" red light is active when the manual Bypass switch

of the ModularEasy is onTEST or BYPASS position. The load is not

protected.

On 9PXMEZ11Ki, it is possible to Bypass the load on a separate Bypass AC source

(see "4.3 9PXMEZ11Ki - with separate Normal and Bypass AC source", page 18 for more details).

9PXMEZ6Ki

1Input/Output terminal blocks

2UPS output switch

3Input/Output cables for

connection to UPS1 and UPS2

416A outlets

5Outlets circuit breaker

6"Bypass" source input UPS1 and

UPS2

7Signal cable for 9PXMEZ

detection to the UPS

9PXMEZ11Ki

UPS output switch 2allows to disconnect the output power of the UPS, for UPS maintenance / replacing.

See "5. Operations", page 20.

ModularEasy status detection 7:

A RJ11 signal cable allows to display the following statuses on the UPS display panel:

• ModularEasyconnectiontoUPS

• Bypassswitchposition.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Eaton UPS Handbücher

Eaton

Eaton 9155 N Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton 93PR Series Handbuch

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton Power Xpert 9395P 250 kVA Handbuch

Eaton

Eaton EX RT 7 Bedienungsanleitung

Eaton

Eaton 9E15Ki Gebrauchsanweisung

Eaton

Eaton Eaton series Bedienungsanleitung

Eaton

Eaton MX Frame 15000 RT Bedienungsanleitung

Eaton

Eaton 9315 Bedienungsanleitung

Eaton

Eaton Evolution 650/650 Rack 1UEvolution 850 Bedienungsanleitung

Eaton

Eaton Powerware 5125 Bedienungs- und Sicherheitshinweise

Eaton

Eaton Power Xpert 9395 Bedienungsanleitung

Eaton

Eaton Powerware 9395 Bedienungs- und Wartungshandbuch

Eaton

Eaton Powerware 9125 Bedienungsanleitung

Eaton

Eaton 700VA Betriebsanleitung

Eaton

Eaton 9PXM Bedienungsanleitung

Eaton

Eaton 93E Bedienungsanleitung

Eaton

Eaton 9125 Two-in-One UPS 2500 Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton BladeUPS none Bedienungsanleitung

Eaton

Eaton Powerware 9155 Bedienungsanleitung

Eaton

Eaton TRIPP LITE Series Montageanleitung

Eaton

Eaton Powerware 9910-E64 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung