Eaton Powerware 9125 Bedienungsanleitung
Powerware 9125 (9910-E30) UPS
Installation Guide for IBM Applications
®
®
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
IBM, pSeries, AIX, xSeries, AS/400, OS/400, and RS/6000 are registered trademarks and iSeries, OpenPower, and
i5/OS are trademarks of International Business Machines Corp.
Eaton, Powerware, X-Slot, and LanSafe are registered trademarks and ConnectUPS is a trademark of Eaton
Corporation or its subsidiaries and affiliates.
Burndy is a registered trademark of Framatone Connectors International.
ECopyright 2007 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1 i
Table of Contents
1 Installation 11.........................................................
Parts List 11..........................................................................
UPS Internal Battery Connection 14..........................................................
Setup and Installation 15.................................................................
Tools Required 15....................................................................
Rack-Mount Setup 15.................................................................
Tower Setup 21.....................................................................
EBM Installation 25.....................................................................
PDM Installation 27.....................................................................
UPS Installation 28.....................................................................
Remote Emergency Power-off Installation 28...................................................
Power Connections and Startup 30..........................................................
Typical Power Connections 34..............................................................
Load Segments 39......................................................................
2 Operation 41..........................................................
Turning the UPS On 41...................................................................
Starting the UPS on Battery 41.............................................................
Turning the UPS Off 42...................................................................
Initiating the Self-Test 42.................................................................
Operating Modes 43....................................................................
Normal Mode 44....................................................................
Battery Mode 45....................................................................
Bypass Mode 46.....................................................................
Standby Mode 46....................................................................
Configuration Mode 47...................................................................
3 Communication 51.....................................................
Single-Port Card 51.....................................................................
Communication Options 54................................................................
i5, iSeries, or AS/400 and Serial Server Interface Overview 55....................................
Serial (TTY) Interface Overview 57...........................................................
p5 or pSeries with Logical Partitions Interface Overview 58.........................................
4 Service and Support 59.................................................
TABLE OF CONTENTS
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1
ii
This page intentionally left blank.
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1 1
Chapter 1 Installation
IBM part numbers are subject to change without notice.
Parts List
Table 1. E30 Base Configuration (42R8069)
Quantity IBM MN IBM FC IBM PN Eaton®PN Description
1E30 —42R8069 103002728-3992 E30 UPS 3000 VA, 2100W (in shipping carton or
factory-installed in rack)*
05145993-3 UPS Front Cover*
164201570 Read Me First Card
103004084-3991 (2) Rack Mounting Bracket Kits*:
S(2) Mounting Brackets (157606331-003)
S(4) Mounting Bracket Screws (M4×8) (180500136-202)
S(2) Mounting Handles (130500110-001)
S(4) Mounting Handle Screws (#8-32×1/2”) (180500200-002)
103006173 Left Rail Assembly*
103006172 Right Rail Assembly*
1 — — 42R8070 103004081-3992 E30 Accessory Kit
* If the UPS is factory-installed in an IBM rack, these items are pre-assembled.
Table 2. E30 Application Matrix
IBM
MN
IBM
FC
IBM
PN Eaton PN Description
i5/
iSeriest
Tower
IEC
i5/
iSeries
Tower
NEMA
p5/
pSeries®
Tower
IEC
p5/
pSeries
Tower
NEMA
p5/
pSeries
Rack
WW
i5/
iSeries
Rack
WW
—6570 42R4320 103003920-3991 NEMA
PowerPass®
Distribution
Module (PDM)
— 1 — 1 — —
—2939* 42R4332 103004741-5591 Relay-Serial
Card and Cable
Kit (DB-9,
1.8m/6 ft; DB-25,
9.1m/30 ft)
1 1 — — — 1
* Maximum: One FC 2934 or 2939 per E30 UPS.
NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide
INSTALLATION
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1
2
Table 3. E30 Options Matrix
IBM
MN
IBM
FC
IBM
PN
Eaton
PN Description
i5/
iSeries
Tower
IEC
i5/
iSeries
Tower
NEMA
p5/
pSeries
Tower
IEC
p5/
pSeries
Tower
NEMA
p5/
pSeries
Rack
WW
i5/
iSeries
Rack
WW
—2934* 39J4824 116750221-001 ConnectUPSt-X
Web/SNMP Card
— — Min: 0, Max: 1 —
—6644 42R8071 103002837-3992 Extended Battery
Module (EBM)
Min: 0, Max: 4
— — 42R8072 103004082-3992 EBM Accessory
Kit
1 per FC 6644
* Maximum: One FC 2934 or 2939 per E30 UPS.
NOTE IEC: IEC Countries (e.g., UK, Italy, etc.); NEMA: NEMA Countries (e.g. U.S. and Canada); WW: Worldwide
Table 4. E30 Accessory Kit (42R8070)
Quantity Eaton PN Description
1164201374 Powerware 9125 Two-in-One UPS (2500/3000 VA) User’s Guide
1164201696 Powerware 9125 (9910-E30) Installation Guide for IBM Applications
4152601942-001 IEC 320-C13 to C14, 10A Equipment Power Cords (2m/6.6 ft)
1152601971-001 IEC 320-C19 to C20, 16A Equipment Power Cord (4.5m/14.8 ft)
1103004870 Software Suite CD
1124102044-001 Serial Cable (DB-9 to DB-9, 1.8m/6 ft)
1116750226-001 Serial Cable (RJ-45 to DB-9, 1.8m/6 ft)
2130500110-001 Mounting Handles
4180500200-002 Mounting Handle Screws (#8-32×1/2”)
405147635-3 Pedestals
4180500137-003 Pedestal Mounting Screws (M4×10 mm)
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
INSTALLATION
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1 3
Table 5. E30 6644 EBM Components (42R8071)
Quantity IBM MN IBM FC IBM PN Eaton PN Description
1 — 6644 42R8071 103002837-3992 E30 6644 EBM 2U High (in shipping carton or factory-installed in
rack)*
05145993-3 EBM Front Cover*
157606331-003 (2) Mounting Brackets*
180500136-202 (4) Mounting Bracket Screws (M4×8)*
103006173 Left Rail Assembly*
103006172 Right Rail Assembly*
1 — — 42R8072 103004082-3992 EBM Accessory Kit
* If the EBM is factory-installed in an IBM rack, these items are pre-assembled.
Table 6. E30 6644 EBM Accessory Kit (42R8072)
Quantity Eaton PN Description
1164201375 Powerware 9125 Two-in-One EBM (2500/3000 VA) User’s Guide
2130500110-001 Mounting Handles
4180500200-002 Mounting Handle Screws (#8-32×1/2”)
2157605902-003 Joining Brackets
4180500153-306 Joining Bracket Screws (M4×10 mm)
1157606358-001 EBM Fixed Cover Plate
1180500153-104 Pan-Head Screws (M3×6 mm)
1103002843-3992 Rail Hardware Kit (metric):
S(8) M5×12 Pan-Head Screws
S(8) M5×10 Flat-Head Screws
S(4) M5×16 Hex-Head Screws
S(4) M5 Clip Nuts
S(2) Square-Hole Adapter Plates
INSTALLATION
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1
4
Table 7. FC 6570 PDM (42R4320)
Quantity Eaton PN Description
1103003920-3991 FC 6570 PDM
1164201392 Powerware 9125 PDM (2500/3000 VA) User’s Guide
1103005260 Accessory Kit:
S(1) 2.5m (8 ft) IEC 320-C19 to IEC 320-C20 Jumper Cable (152601948-001)
S(2) Joining Brackets (157605902-003)
S(4) Joining Bracket Screws (M4×10 mm) (180500153-306)
UPS Internal Battery Connection
NOTE Check the battery recharge date on the shipping carton label. If the date has expired
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
To ensure proper battery operation before installing the UPS:
1. Verify that the UPS is off and unplugged.
2. Remove the UPS front cover (see Figure 1).
Figure 1. Removing the Front Cover
3. Connect the internal battery connector (see Figure 2).
Figure 2. Connecting the Internal Battery Connector
INSTALLATION
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1 5
4. Reinstall the UPS front cover (see Figure 3).
Figure 3. Reinstalling the Front Cover
Setup and Installation
The E30 UPS is designed for flexible configurations and can be installed
in a rack, as a standalone cabinet, or in a tower configuration.
NOTE For UPS rack installations: If the UPS is pre-installed in an IBM rack, continue
to “UPS Installation” on page 18. If you are installing the UPS in an IBM iSeries (0550, 0551,
0554, or 0555 types) or pSeries (7014 type) rack, continue to the following section, “Tools
Required.” If you have another type of rack, contact your service representative (see page 49).
NOTE For UPS standalone cabinet or tower installations: Continue to “Tower
Setup” on page 11 to begin the UPS setup.
Tools Required
To assemble the components, the following tools may be needed:
SMedium flat-bladed screwdriver
S#2 Phillips screwdriver
S7and8mmwrenchorsocket
Rack-Mount Setup
The rail kit can be installed in 48-cm (19-inch) racks and needs only 2U of
valuable rack space.
NOTE Mounting rails are required for each individual cabinet and are located in the UPS
and EBM cartons. All hardware is supplied.
NOTE The UPS and any optional cabinets MUST be installed at the bottom of the rack. If
placed in a rack with existing equipment, the rack must be reconfigured to allow the UPS
installation at the bottom of the rack.
INSTALLATION
EATON Powerware®9125 (9910-E30) UPS Installation Guide for IBM®Applications S164201696 Rev 1
6
Each rail kit requires one (1) of each item in the following list:
SLeft rail assembly (located in the UPS and EBM cartons)
SRight rail assembly (located in the UPS and EBM cartons)
SRack mounting bracket kit (located in the UPS and EBM cartons)
SRail hardware kit (located in the E30 UPS and EBM accessory kits)
To install the rail kit(s):
1. Loosen the assembly wing nuts on both rail assemblies and adjust
the rail size for the depth of your rack (see Figure 4).
Assembly Wing Nuts
Front
Rear
Rear Hold-Down Bracket
Figure 4. Adjusting the Rail Depth
2. Select the proper holes in the rail for positioning the UPS and any
optional cabinets in the rack.
3. Secure the rail to the front of the rack with two pan-head screws
and one adapter plate. Insert the screws through positions 3 and 4
oftherail(seeFigure5).
NOTE Do not tighten the screws until the UPS or EBM is installed.
Andere Handbücher für Powerware 9125
9
Inhaltsverzeichnis
Andere Eaton UPS Handbücher
Eaton
Eaton 93PM-L IAC-B Bedienungsanleitung
Eaton
Eaton 9E Bedienungsanleitung
Eaton
Eaton 93PM IBC-LW Bedienungsanleitung
Eaton
Eaton 500 Bedienungsanleitung
Eaton
Eaton Powerware 9390 Bedienungsanleitung
Eaton
Eaton Powerware 9390 Bedienungsanleitung
Eaton
Eaton Powerware 9395 550 kVA MBM Bedienungsanleitung
Eaton
Eaton Powerware 9125 Bedienungsanleitung
Eaton
Eaton DIN24240DC Bedienungsanleitung
Eaton
Eaton 93PM UPS Bedienungsanleitung
Eaton
Eaton 5S 1000 Bedienungsanleitung
Eaton
Eaton 91PS UPS 8-40 kW Handbuch
Eaton
Eaton TRIPP LITE Series Montageanleitung
Eaton
Eaton Powerware 9355 Bedienungsanleitung
Eaton
Eaton 9PX6KIRTN-L Bedienungsanleitung
Eaton
Eaton UPS 20 Bedienungsanleitung
Eaton
Eaton MBP6Ki Bedienungsanleitung
Eaton
Eaton 9PXM8S4K Bedienungsanleitung
Eaton
Eaton Powerware 9355 Bedienungsanleitung
Eaton
Eaton Power Xpert 9395P-1200 Bedienungsanleitung
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
Block
Block PC-0524-400-0 Bedienungsanleitung
CyberPower
CyberPower CP585LCD Bedienungsanleitung
CyberPower
CyberPower Office Tower Series UPS 1000 Bedienungsanleitung
CyberPower
CyberPower BM100 Bedienungsanleitung
Best Power
Best Power 610 Bedienungsanleitung
Best Power
Best Power Unity/I UT3K Bedienungsanleitung
