Eaton Powerware 9120 Bedienungsanleitung

POWERWARE®9120

User’s Guide

6000VA

www.powerware.com

POWERWARE 9120

6000VA

User Guide

Important Notice

The UPS ground (earth) conductor carries leakage current from the loads in addition to

any leakage current generated by the UPS. This UPS generates no more than 1 mA of

current. To limit the total leakage current to 3.5 mA, the load leakage must be limited to

2.5 mA. The UPS must have a good (low-impedance) ground (protective earth) connec-

tion to provide a safe path for leakage current.

OMM91206kRev1.qxd

If You Have a Question

Customer Support

If you have a question or problem, Table 10, Troubleshooting, may help. If you need

more help, please have your UPS model number and serial number (on the back

label) nearby, and call the Eaton Power Quality office nearest you (see the Eaton

Power Quality offices section). Eaton Power Quality’s service technicians have in-

depth knowledge of the UPS and power problems.

Eaton Power Quality may tell you the UPS must be returned. If this happens, we will

give you a Return Authorisation (RA) number. When you return a Powerware 9120 to

the factory for any reason, please use the original packing material in which your

unit was shipped to you. You may be responsible for repair charges for damaged

units which are not packed in Eaton Power Quality packing material. If you have

discarded the original packing material, please call the nearest Powerware office so that

we can ship new packing material to you. If you have any questions, please feel free to

call or fax the nearest Eaton Power Quality office. Please do not return your Powerware

9120 without calling Eaton Power Quality first. Eaton Power Quality will advise you

where to ship your Powerware 9120.

Powerware reserves the right to change specifications without prior notice.

Where the brand name “Powerware” is used,

the term refers to Eaton’s Powerware Division, trading in Australia

as Eaton Power Quality Pty Ltd

Table of Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1.0 UPS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.1 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.2 Rear Panel View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.3 Connections to Mains and Load . . . . . . . . . . . . . . . . . . . . . . . . . .6

3.0 Quick Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.1 UPS Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4.2 Turning the UPS On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.3 Turning the UPS Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.4 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4.5 Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

5.0 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6.0 Additional UPS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

6.1 Inverter Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

6.2 Communication Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

6.3 Comunication Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

6.4 SNMP/Web Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

6.5 Relay Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7.0 Installing Lansafe Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

8.0 Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

8.1 How to Replace Internal Batteries . . . . . . . . . . . . . . . . . . . . . . . .19

8.2 Recyling the Used Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

9.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

10.0 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

11.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Powerware Australia/New Zealand Offices . . . . . . . . . . . . . . . . . . . .31

Trademarks

Windows is a registered trademark of Microsoft Corporation.

All other brand and product names are trademarks or registered trademarks of their

respective holders.

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS!

This User Guide contains important instructions for your Powerware 9120 that must be followed

during installation and maintenance of the UPS and batteries.

The installation and use of this product must comply with all national, federal, state, municipal, or

local codes that apply. For assistance, call Powerware Service or your local Powerware office.

If the Powerware 9120 has been damaged during shipment, call your vendor immediately.

If the Powerware 9120 is stored, the batteries should be recharged every 6 months. If stored

above 25°Celsius, recharge the batteries more often.

CAUTION!

Whenever the Powerware 9120 is “On,” there may be dangerous voltage present at the unit’s

outlet terminals. This is because the unit’s battery supplies power even if the unit is not con-

nected to supply. The unit contains dangerous voltages.

To reduce the risk of electric shock, install in a temperature-controlled and humidity-

controlled indoor area free of conductive contaminants.

With the exception of the user-replaceable batteries, all servicing of this equipment must be

performed by qualified service personnel.

Before maintenance or repair, all connections must be removed. Before maintenance, repair,

or shipment, the unit must be completely switched off and unplugged or disconnected.

1.0 UPS Features

The Powerware 9120 provides protection against power problems, including power outages,

brownouts, and sudden increases in power. It also provides spike suppression and line noise fil-

tering to protect your equipment. Front panel LEDs and an audible alarm keep you aware of the

unit’s status. Use the drawings on this and the following pages to identify features of the unit.

Fig 1. Powerware 9120 6kVA Controls and Indicators

2.0 Installation

2.1 Environment

1. The UPS should be installed in a controlled environment. A controlled environment is one

that is indoor, temperature controlled, free from conductive contaminants, dust, fumes and

moisture.

The UPS is intended for indoor use only.

Provide adequate ventilation, 100 mm clearance at the rear of the UPS and 50 mm on the

sides of the UPS.

The unit must have unrestricted airflow.

To maximise the battery life, an ambient temperature of 15oC to 25oC is recommended.

2. Environmental Specifications

Ambient Operating Temperature < 1500m 0oC to 40oC

1500m - 3000m 10oC to 35oC

Recommended Temperature 15oC to 25oC

Storage Temperature -15oC to +50oC

Cooling Type Forced Air

Humidity 0.95% non-

condensing

2.2 Rear Panel View

Fig 2. Powerware 9120 6kVA Rear Panel

2.3 Connections to Mains and Load

The installation, wiring and connection must be carried out by qualified personnel only. The

installation must comply with all current Wiring Rules and Regulations, Local, State and Federal

statutes, Legislation and Regulations.

CAUTION !

The UPS contains high voltage and current levels which could injure or kill personnel

and damage equipment.

2.3.1 Installing the UPS

1. Ensure that the UPS protective device and the cabling are sized to accomodate the

ratings as listed in Figs 3 & 4.

2. Install UPS wiring system in accordance with Fig 5, for a Single Supply Input, or

Fig 6 for a Dual Supply Input. A Dual Supply is normally to provide additional system

validating in the event of a feeder failing.

Fig 3. Single Supply Wiring

Note: 1. Max Cable Size into Terminals is 10sq. mm. Stranded Cable

2. For Wiring Diagram refer to Fig 5

Fig 5. Single Supply Wiring

Note: For Terminal Connection refer to Fig 3

Fig 4. AC Supply with Separate Bypass Supply

Note: 1. Max Cable Size into Terminals is 10sq. mm. Stranded Cable

2. Currents quoted are for 240V AC units

3. For Wiring Diagram refer to Fig 6

Fig 6. AC Supply with Separate Bypass Supply

Note: For Terminal Connection refer to Fig 4

Andere Handbücher für Powerware 9120

Inhaltsverzeichnis

Andere Eaton UPS Handbücher

Eaton

Eaton 5S Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Konfigurationshandbuch

Eaton

Eaton Ellipse PRO 1600 DIN Bedienungsanleitung

Eaton

Eaton SPM Series Bedienungsanleitung

Eaton

Eaton 5000 VA Bedienungsanleitung

Eaton

Eaton 9PX Montageanleitung

Eaton

Eaton 93PM 150 kW SIAC-B Three-Wire Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton 9E-IN 1K Bedienungsanleitung

Eaton

Eaton Powerware 9170+ Bedienungsanleitung

Eaton

Eaton 9315 Bedienungsanleitung

Eaton

Eaton BladeUPS none Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton EX 700 Bedienungsanleitung

Eaton

Eaton Ellipse PRO 650 Bedienungsanleitung

Eaton

Eaton 9E1000i Bedienungsanleitung

Eaton

Eaton 9315 Bedienungsanleitung

Eaton

Eaton Powerware 9390 Bedienungsanleitung

Eaton

Eaton Power Xpert Plus 1 Bedienungsanleitung

Eaton

Eaton 5E650iUSB-AU Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Bedienungsanleitung

Eaton

Eaton 93PM IBC-L Handbuch

Eaton

Eaton Power Xpert 9395 Betriebsanleitung

Eaton

Eaton Powerware 9130 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung