EAW MKC Series Bedienungsanleitung

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 1

MKC Series Large Ceiling Bracket Instructions

Original Instructions

These instructions are for dening acceptable MKC Large Ceiling Bracket installations to a

mounting surface and for installing an MKC Series Loudspeaker to an MKC Series Ceiling Bracket

& Metal Pan & Tilt Bracket.

IMPORTANT SAFETY INSTRUCTIONS – READ THIS FIRST

Safety Instructions

Read and heed all warnings and safety instructions in this manual before using this product.

Failure to follow these precautions may result in damage, injury, or death.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Clean only with a dry cloth.

6) Install loudspeaker in accordance with the manufacturer's instructions.

7) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus that produce heat.

8) Only use attachments/accessories specied by the manufacturer.

9) Refer all servicing to qualied service personnel. Servicing is required when the apparatus

has been damaged in any way, does not operate normally, or has been dropped.

10) Use personal protective equipment not limited to gloves, safety goggles, ear protection,

and lifting supports.

Suspension Warnings

WARNING: Suspending anything, especially overhead of people, should be done with extreme

caution. Always engage the services of a certied professional who is qualied to determine

the requirements for and to implement overhead rigging. Only persons with the knowledge

of proper hardware and safe rigging techniques should attempt to suspend loudspeakers

overhead. Failure to follow these precautions may result in damage, injury, or death.

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 2

MKC Series Large Ceiling Bracket Instructions

Avertissements de suspension

AVERTISSEMENT: Suspendre quoi que ce soit, en particulier les frais généraux de personnes,

doit être fait avec une extrême prudence. Toujours engager les services d'un professionnel

certié qui est qualié pour déterminer les conditions requises et à mettre en œuvre le

gréement en tête. Seules les personnes ayant la connaissance du matériel approprié et les

techniques sécuritaires de gréage devraient tenter de suspendre les haut-parleurs audessus. Le

non-respect de ces précautions peut entraîner des dommages, des blessures ou la mort.

Avvertenze sospensione

AVVERTENZA: Sospendere nulla, soprattutto sovraccarico di persone, deve essere fatto con

estrema cautela. Inserire sempre i servizi di un professionista certicato che si è qualicato

per determinare i requisiti di e ad attuare manovre in testa. Solo le persone con la conoscenza

di tecniche di assemblaggio di sicurezza hardware e dovrebbero tentare di sospendere gli

altoparlanti in testa. La mancata osservanza di queste precauzioni può provocare danni, lesioni

o morte.

Advertencias de suspension

ADVERTENCIA: La suspensión de cualquier cosa, especialmente por encima de las personas, se

debe hacer con mucho cuidado. Siempre contratar los servicios de un profesional certicado

que está calicado para determinar los requisitos para implementar y para las maniobras de

elevación. Sólo las personas con el conocimiento de las técnicas de aparejo de seguridad de

hardware adecuada y deben intentar suspender altavoces por encima. El incumplimiento de

estas precauciones puede resultar en daños, lesiones o muerte.

Suspension Warnungen

WARNUNG: Schwebend alles, vor allem Aufwand von Menschen, sollte mit äußerster Vorsicht

erfolgen. Immer engagieren, die Dienste eines zertizierten Pro, der qualiziert ist, die

Anforderungen zu bestimmen und Überkopfmontage zu implementieren. Nur Personen mit

der Kenntnis der richtigen Hardware und sichere Rigging Techniken sollten Lautsprecher Kopf

auszusetzen versuchen. Die Nichtbeachtung dieser Vorsichtsmaßnahmen kann zu Schäden,

Verletzungen oder zum Tod führen.

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 3

MKC Series Large Ceiling Bracket Instructions

3. Pass unterminated cable ends through the knockout on the input cover and wire loudspeaker (skip if no

connections).

4. Attach input cover to loudspeaker using (9) M5 x 18 screws.

1. Inventory your kit

**Tools Needed: (2)13mm wrench, 2.5mm & 6mm Allen wrench**

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 4

MKC Series Large Ceiling Bracket Instructions

2. MKC Series Large Ceiling Bracket limits

of use

a. The MKC Series Large Ceiling

Brackets are designed to mount MKC

Series loudspeakers only. No other

EAW Product Series may be used with

this bracket.

b. The MKC Series Large Ceiling

Brackets is designed to mount only

one loudspeaker per bracket.

c. Any geometric or structural modications to the MKC Large Ceiling Bracket or

hardware are not EAW-approved will void the warranty and may result in damage, injury,

or death.

d. WARNING: Take care when lifting larger MKC Series products to avoid harm or

damage to product.

Exploded view of ceiling bracket

kit with plastic Pan & Tilt Mount

MKC80 utilizing Ceiling Bracket with

Pan & Tilt Bracket

3. Installation of the MKC Series Metal Pan & Tilt Bracket

to a Ceiling Bracket

a. Test t an MKC Series Ceiling Bracket (A)/Metal Pan

& Tilt Bracket (E) on an MKC Series Loudspeaker to

conrm the correct angle, loudspeaker and bracket

orientation before installing the wall bracket

to the mounting surface. Also verify desired

conguration and mounting procedure will

allow for easy tool access.

b. Congurations - Depending on mounting option

used, MKC Series products may be installed in a

vertical or horizontal orientation with the ability to

pan and tilt depending on mounting position of the

wall bracket.

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 5

MKC Series Large Ceiling Bracket Instructions

c. Mounting options

NOTE: It i s recommended that you consult a building professional for the proper mounting

hardware before mounting the bracket. Due to various construction methods and materials, the

hardware for securing the bracket to the mounting surface is not supplied. It is required that the

use of hardware locking methods, not limited to lock washers, thread-locker, or nylon-retention

feature, be applied when securing the pan and tilt wall bracket to the mounting surface or

structure.

Each MKC Series Metal Pan & Tilt wall bracket (E) holes will need to mount to Ceiling Bracket (A)

i. All four mounting holes will need to mount to ceiling bracket utilizing

4x M6x20 bolts (D), 4x Lock Washers (C), and 4x Flat Washers (B).

ii. Consider orientation of loudspeaker (horizontal or vertical) before securing bracket

to the wall.

4. Installation of an Ceiling Bracket (A) to

structure

a. Once the wall bracket is secured to

ceiling bracket, mount the ceiling bracket

to a permanent structure using available

mounting holes on back and top of the

ceiling bracket

i. Note if loudspeaker will need to pan

or tilt, or perform a combination of

both options.

ii. Consider orientation of

loudspeaker (horizontal or veritical)

before securing speaker bracket.

iii. To connect bracket to the speaker,

remove hardware from rear of MKC

loudspeaker, place speaker bracket

over mounting pattern, and secure

with previously removed hardware.

Cable Pass Thru Only

Ceiling Bracket Only

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 6

MKC Series Large Ceiling Bracket Instructions

b. Connecting Speaker Bracket to Wall Bracket

i. Line up the two exposed speaker bracket

holes with opening in pivot block

ii. Slide

Button Head Hex Drive Screw

connect brackets together

iii. Tighten with lock and oversized

washers using 6mm allen wrench.

Connecting the Pan & Tilt Wall and

Speaker Brackets

5. Installation of an MKC Series Loudspeaker

to the Metal Pan & Tilt Bracket.

a. Choosing an MKC Series

Loudspeaker conguration

i. Note if loudspeaker will need to pan

or tilt, or perform a combination of

both options.

ii. Consider orientation of loudspeaker

(horizontal or vertical) before

securing speaker bracket.

iii. To connect bracket to the

speaker, remove hardware from

rear of MKC Series, place

speaker bracket over mounting

pattern, and secure with previously

removed hardware.

Each mounting hole will correspond to

mounting hole on an MKC Series product

c. Conguring Pan & Tilt angles

NOTE: Not all angles will be achievable due to

the physical restraints of loudspeakers used with

bracket.

NOTE: Depending on orientation of the wall

bracket pan and tilt hardware conguration will

vary

Tel 800 992 5013 / +1 508 234 6158

www.eaw.com 7

MKC Series Large Ceiling Bracket Instructions

6. Review the MKC Series Loudspeaker installation

a. Conrm the loudspeaker is level or plumb depending on the conguration.

b. Conrm the aim angle is as expected.

c. Conrm all hardware is tight.

7. Maintenance of an MKC Series Brackets installation

a. WARNING: Not following Maintenance instructions could result in equipment

damage, serious injury or death.

b. Maintenance should only be performed by an experienced technician.

c. As with any professional loudspeaker system, routine maintenance must be conducted in

order to ensure the longevity and safe, consistent performance.

d. Inspect the MKC Series Brackets for damage. Brackets with visible damage should be

replaced and discarded.

e. Inspect hardware securing the bracket to the mounting surface for corrosion or

looseness. Tighten loose hardware and consider installing hardware locking methods.

Replace and discard corroded hardware.

f. Inspect hardware mounting the MKC Series loudspeaker to the brackets for corrosion or

looseness. Tighten loose hardware. Replace and discard corroded hardware.

g. Clean the MKC Series Brackets and MKC Series loudspeakers with a dry cloth.

i. Loosen bolt and nut locking the current angle

on the Pivot Block in place using (2) 10mm

wrenches (see image on previous page)

ii. The lock pin will work in increments of 5

degrees (See left image). Set desired

rotate or tilt angle for pivot block.

iii. Loosen

Button Head Hex Drive Screw

connecting wall and cabinet bracket using a

6mm allen wrench

iv. Once desired pan or tilt angle is achieved,

fully tighten the bolt.

10°,25°10°,25°

20°,15°,30°20°,15°,30°

5°,20°5°,20°

Andere Handbücher für MKC Series

Dieses Handbuch passt für folgende Modelle

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung