Ecler TRAILSB6T Bedienungsanleitung

TRAILSB6T

LOUDSPEAKERS

Concealable Subwoofer

USER MANUAL

INDEX

1. IMPORTANT REMARK.................................................................................... 3

2. IMPORTANT SAFETY INSTRUCTIONS .............................................................. 4

3. IMPORTANT NOTE.........................................................................................6

4. INTRODUCTION ............................................................................................. 6

5. MAIN SPECIFICATIONS................................................................................... 6

6. CONNECTION ................................................................................................ 7

7. LOCATION AND INSTALLATION ......................................................................8

6.1 Procedure for installation in a suspended ceiling ........................................... 9

6.2 Flat surface installation procedure ............................................................... 10

6.3 Procedure for installation behind a partition wall........................................ 11

8. TECHNICAL SPECIFICATIONS ........................................................................ 12

9. CONTENTS OF PACKAGING .......................................................................... 12

1. IMPORTANT REMARK

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert

the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or

moisture.

WARNING: An apparatus with Class I construction shall be connected to a mains

socket-outlet with a protective earthing connection.

2. IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or pinched particularly at the

plugs, convenience receptacles, and at the point where they exit from the

apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug the apparatus during lightening sorts or when unused for long

periods of time.

13. Refer all servicing to qualified personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

14. Disconnecting from mains: Switching off the POWER switch all the

functions and light indicators of the amplifier will be stopped, but fully

disconnecting the device from mains is done unplugging the power cord

from the mains input socket. For this reason, it always shall remain readily

operable.

15. Equipment is connected to a socket-outlet with earthing connection by

means of a power cord.

16. The marking information is located at the bottom of apparatus.

17. The apparatus shall not be exposed to dripping or splashing and that no

objects filled with liquids, such as vases, shall be placed on apparatus.

NOTE: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

WARNING: This product must not be discarded, under any

circumstance, as unsorted urban waste. Take to the nearest electrical

and electronic waste treatment centre.

NEEC AUDIO BARCELONA, S.L. accepts no liability for any damage that may be

caused to people, animal or objects due to failure to comply with the warnings

above.

3. IMPORTANT NOTE

Congratulations. You now possess the result of careful design and meticulous

manufacturing. We are very grateful for your trust in purchasing our TRAILSB6T

concealable subwoofer.

In order to obtain maximum effectiveness and performance, it is VERY

IMPORTANT, prior to connection, to carefully read and to take into account the

instructions given in this manual. To guarantee optimum operation, we

recommend that all maintenance be carried out by our authorised Technical

Services.

4. INTRODUCTION

TRAILSB6T is intended as a bass reinforcement and is constructed of wood, with a

very compact design. It incorporates a 6.5-inch, 60 Wrms, 8 Ω driver, a transformer

with four selectable powers for use in 70/100 V lines and an internal low-pass

filter.

It has been specially designed to meet the requirements of a permanent

installation, in which low visual impact and integration with its surroundings are

essential: concealed in suspended ceilings and on surfaces, etc. Installation

accessories are included. Available in black

5. MAIN SPECIFICATIONS

Small-format, sub-bass woofer enclosure made of wood, for strengthening

TRAIL 103 type or other loudspeaker in ceilings or other small-format boxes

Externally-selectable low-pass filter: 150 Hz / OFF

Suitable for 70/100 V and low-impedance lines

Power selector 60/30/15/7.5 W and 8 Ohms

Euroblock input connector

Can be installed in suspended ceilings, partition walls or on walls, etc.

Support for suspended ceilings and grille included

Installation system included

Available in black

6. CONNECTION

The TRAILSB6T operates into high or low impedance. For this reason, it has a rear

panel fitted with a 5-position switch for operating-mode selection. The first four

positions enable the system to operate into high impedance mode, and the fifth is

for low impedance.

The four positions of the power selector for the 70/100 V line allow the maximum-

power configuration at which each unit operates. Therefore, the lower positions

are used in areas requiring low SPL (7.5 W or 15 W) and the upper positions are

for areas requiring higher levels (30 W or 60 W).

Note: if the loudspeaker is used in 70V installations, the corresponding powers for

the 100V position will be reduced to half those indicated on the switch. To one

quarter for 50V installations.

The fifth position corresponds to low-impedance operation (8 Ω) and a maximum

power of 60 W. If this setup is adopted, consideration must be given to amplifier

limits when several loudspeakers are connected to its output, especially if the

overall impedance is below 4 Ω. Furthermore, it is important that the cable

connecting the amplifier outputs to the loudspeakers is of good quality and as

short as possible; this is of special significance when long distances have to be

covered and loudspeaker impedance is low.

Note: The loudspeaker distribution along a 70/100V line historically arises from

the technical requirement to mix loudspeakers of different impedances and/or

powers on the same amplification line or channel, but without any need to worry

about the total impedance of the full assembly. Moreover, this solution enables

long cable runs with significantly smaller sections that those usually employed in

low-impedance installations, but with minimum power losses.

WARNING! If the system is accidentally connected with the switch in the 100 V/60

W position to a low-impedance amplifier, no damage will be caused to the

loudspeaker, but its performance will be well below its specifications. If the

loudspeaker is accidentally connected to a 70 V/100 V network, in the 8 Ωposition,

it will be seriously damaged.

7. LOCATION AND INSTALLATION

TRAILSB6T provides various installation systems. The packaging contains all the

accessories required for the various options. Installation in suspended ceiling, on a

flat surface (wall or ceiling) and behind partition walls.

In general, the following rules will be followed:

The unit must always be installed on firm, solid surfaces when the

installation is on a flat surface (wall or ceiling).

Suspended ceiling installation: TRAILSB6T can be installed in suspended

ceilings with 60 cm wide profiles.

For good sound reproduction, there must not be any obstacles between the

loudspeaker and the audience.

The sound-pressure levels must be adapted to the reproduction needs.

Despite its reduced size, TRAILSB6T provides a much higher performance

than domestic loudspeakers.

Note: the TRAILSB6T loudspeaker may be adapted in several ways to your needs

by means of the supplied installation accessories. The procedures described in this

manual are examples, but there are other installation options that can be executed

by following the instructions in this manual; at corners, walls with angles, on the

floor, concealed in furniture, etc.

49,75

100100

270,25

6.1 Procedure for installation in a suspended ceiling

Before commencing with the securing of the metal fittings, consideration must be

given to the coupling bar because a 68 mm hole must be made in the ceiling for its

installation and that of the trim grille.

1. Screw the metal fittings to the TRAILSB6T using the supplied screws. This

can be executed by using several of the holes in the supports for the

coupling bar installation in the desired position. See figure 1.

2. Execute a 68 mm hole for the coupling bar in the suspended ceiling.

3. Check that the system is stable and then carry out the necessary

connections and adjustments before installing it over the suspended ceiling.

4. Install the loudspeaker with the metal fittings already in place over the

suspended ceiling and leave the system resting on the profiles.

5. Install the coupling bar with the trim grille, passing it through the 68 mm

hole. Push the bar towards the loudspeaker until the grille is flush with the

suspended ceiling.



Figure 1: diagram for suspended ceiling installation

6.2 Flat surface installation procedure

1. Screw the lower metal fitting to the wall at the required height. Remember

that the lower part of the TRAILSB6T will rest on this angle. See figure 2.

2. Check that the system is stable and then carry out the necessary

connections and adjustments before installing the upper support.

3. Screw the upper support to the TRAILSB6T with the supplied screws

(Figure 2) and then screw it to the wall, leaving the loudspeaker resting on

the lower support.

4. Lastly, secure the TRAILSB6T to the lower support using the supplied

screws.

Figure 2: diagram of wall installation

Inhaltsverzeichnis

Andere Ecler Sprecher Handbücher

Ecler

Ecler ARQIS Series Bedienungsanleitung

Ecler

Ecler Philos 10A Bedienungsanleitung

Ecler

Ecler IC6CLASSTR Bedienungsanleitung

Ecler

Ecler eMOTUS8OD Bedienungsanleitung

Ecler

Ecler ARQSB10SATB Benutzerhandbuch

Ecler

Ecler DROP6 Bedienungsanleitung

Ecler

Ecler IW6PLUS Bedienungsanleitung

Ecler

Ecler GIUGIARO DESIGN AUDEO 103 Bedienungsanleitung

Ecler

Ecler eMOTUS5OD Bedienungsanleitung

Ecler

Ecler ARQIS 108BK Bedienungsanleitung

Ecler

Ecler ARQIS105 Bedienungsanleitung

Ecler

Ecler DACORD SB210 Bedienungsanleitung

Ecler

Ecler Audeo 108 Bedienungsanleitung

Ecler

Ecler IW6 Bedienungsanleitung

Ecler

Ecler DACORD SB208 Bedienungsanleitung

Ecler

Ecler NEST106 Bedienungsanleitung

Ecler

Ecler IC6CLASS-54 Bedienungsanleitung

Ecler

Ecler LABI1 Series Bedienungsanleitung

Ecler

Ecler TRAIL103 Bedienungsanleitung

Ecler

Ecler eUC106 Bedienungsanleitung

Ecler

Ecler IG108 Bedienungsanleitung

Ecler

Ecler PhiloS Series Bedienungsanleitung

Ecler

Ecler IC6CLASSTR Bedienungsanleitung

Ecler

Ecler eAMBIT103 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung